show bgp ip neighbor ipv6

Syntax

show bgp ip neigbor ipv6 { all | last-packet-with-error | routes-summary }

show bgp ip neighbor ipv6 ipv6-addr [ flap-statistics | last-packet-with-error [ decode ] | received prefix-filter ]

show bgp ip neighbor ipv6 ipv6-addr { advertised-routes | received-routes | rib-out-routes } [ detail ]

show bgp ip neighbor ipv6 ipv6-addr routes { best | detail [ best | not-installed-best | unreachable] | not-installed-best | unreachable }

show bgp ip neighbor ipv6 ipv6-addr routes-summary

Parameters

advertised-routes

Specifies the display of information about routes advertised to the BGP4+ neighbor in the current session.

detail: Specifies the display of detailed information.

all

Specifies the display of information about all routes advertised to the BGP4+ neighbor in the current session.

flap-statistics

Specifies the display of route flap statistics for routes received from or sent to a BGP4+ neighbor.

last-packet-with-error

Specifies the display of information about the last packet that contained an error received from any device neighbor.

decode: Specifies decoding the packet.

received-routes

Specifies the display of route information received from BGP4 neighbors in the current session.

detail: Specifies the display of detailed information.

rib-out-routes

Specifies the display of information about BGP4 outbound RIB routes.

detail: Specifies the display of detailed information.

routes

best

Specifies the display of information about routes received from the neighbor that are the best BGP4+ routes to their destination.

detail

Specifies the display of detailed information.

best: Specifies the display of information about routes received from the neighbor that are the best BGP4+ routes to their destination.
not-installed-best: Specifies the display of information about routes received from the BGP4+ neighbor that are the best BGP4+ routes to their destination and that were not installed in the route table because the device received better routes from other sources.
unreachable: Specifies the display of information about routes that are unreachable because the device does not have a valid RIP, OSPF, or static route to the next hop.

Modes

Privileged EXEC mode

Examples

The following example shows configuration information and statistics for an IPv6 neighbor that is configured under an IPv4 address family.

show bgp ip neighbors ipv6 2000::1 

  '+': Data in InQueue '>': Data in OutQueue '-': Clearing 
  '*': Update Policy 'c': Group change 'p': Group change Pending 
  'r': Restarting 's': Stale '^': Up before Restart '<': EOR waiting 

1 IP Address: 2000::1 , AS: 1 (EBGP), RouterID: 10.1.1.1, VRF: default-vrf 
  State: ESTABLISHED, Time: 0h0m50s, KeepAliveTime: 60, HoldTime: 180 
  KeepAliveTimer Expire in 15 seconds, HoldTimer Expire in 144 seconds 
  Minimal Route Advertisement Interval: 0 seconds 
  RefreshCapability: Received 

Messages:  Open  Update KeepAlive  Notification  Refresh-Req 
Sent :       1     1      1          0             0 
Received:    1     1      1          0             0 

Last Update Time: NLRI  Withdraw NLRI Withdraw 
Tx: 0h0m33s  ---  Rx: 0h0m35s  --- 

Last Connection Reset Reason:Unknown 
Notification Sent:     Unspecified 
Notification Received: Unspecified 
Neighbor NLRI Negotiation: 
 Peer Negotiated IPV4 unicast capability 
 Peer configured for IPV4 unicast Routes 
Neighbor ipv6 MPLS Label Capability Negotiation: 
Neighbor AS4 Capability Negotiation: 
Outbound Policy Group: 
 ID: 2, Use Count: 1 
BFD:Disabled 
 Byte Sent: 159, Received: 159 
 Local host: 2000::2, Local Port: 179 
 Remote host: 2000::1 , Remote Port: 8042