show mpls bypass-lsp

Use the show mpls bypass-lsp command for displaying all dynamic bypass LSPs along with static bypass LSPs.

Syntax

show mpls bypass-lsp [ debug | detail | down | dynamic | extensive | name | static | up [ detail | extensive | wide ] | wide ]
show mpls bypass-lsp dynamic [ debug | detail | extensive | interface [ ethernet | ve ] | name | wide ]
show mpls bypass-lsp static [ debug | detail | extensive | interface | name | wide ]

Parameters

debug
Displays the MPLS Bypass LSP extensive debug information.
detail
Displays the MPLS bypass LSP information in detail.
down
Displays the operationally down bypass LSPs information.
extensive
Displays the MPLS bypass LSP information with extensive detailed information.
interface
Displays the MPLS dynamic bypass LSP interface information.
ethernet
Specifies the ethernet interface.
ve
Specifies the VE interface.
name
Displays an MPLS bypass LSP by the specified name.
static
Displays the MPLS static bypass LSP information.
up
Displays the operationally UP bypass LSPs information.
wide
Displays MPLS bypass LSP brief wide information.

Modes

Privileged EXEC mode

Usage Guidelines

MPLS is supported on the Extreme 8820, SLX 9740, SLX 9640, and SLX 9540 devices only.

Examples

The following example displays the output of the show mpls bypass-lsp command.

device# show mpls bypass-lsp
Note: Bypass LSPs marked with + are dynamic bypass LSPs
Bypass LSP           To               Admin Oper  Tunnel   Up/Dn Retry Active      
Name                 Address          State State Intf     Times Num   Path        
my-bypass-lsp        20.20.20.20      UP    UP    tnl3     1     0     path-for-bypass-lsp

The following example displays the output of the show mpls bypass-lsp command with the static wide options

device# show mpls bypass-lsp static wide
Bypass LSP           To               Admin Oper  Tunnel   Up/Dn Retry Active      
Name                 Address          State State Intf     Times Num   Path        
my-bypass-lsp        20.20.20.20      UP    UP    tnl3     1     0     path-for-bypass-lsp                                             

The following example displays the output of the show mpls bypass-lsp command using the extensive option.

device# show mpls bypass-lsp extensive
LSP my-bypass-lsp, to 20.20.20.20
 From: 29.29.29.29, admin: UP, status: UP, tunnel interface(primary path): tnl3
 Times primary LSP goes up since enabled: 1
 Adaptive
 Primary path: path-for-bypass-lsp, up: yes, active: yes
  Maximum retries: None, no. of retries: 0
  ReoptimizeTimer configured 360 
   ReoptimizeTimer next expiration in 93 seconds 
  Setup priority: 7, hold priority: 0, cos: 3
  Max rate: 1000 kbps, mean rate: 1000 kbps, max burst: 5000 bytes
  Tie breaking: random, hop limit: 6
  Exclude any of admin groups: 15 16 17
  Exclude interface(s): Eth 1/3
  CSPF-computation-mode configured: te-metric
  Constraint-based routing enabled: yes
   Path calculated using constraint-based routing: yes
   Path calculated using interface constraint: no
   Path calculated using te-metric
   Path cost: 2
  Explicit path hop count: 1
   18.18.18.18(S)
  Recorded routes:
   Protection codes/Rtr Id flags: P: Local  N: Node  B: Bandwidth  I: InUse R: RtrId    
   18.29.1.18 -> 18.20.1.20
 Bypass Tunnel bandwidth
  Maximum bandwidth: 1000 kbps 
  Reservable bandwidth [priority] kbps:
   [0] 1000 [1] 1000 [2] 1000 [3] 1000
   [4] 1000 [5] 1000 [6] 1000 [7] 1000
  Current signaled rate: 1000 kbps
 Active Path:
  Tunnel interface: tnl3, outbound interface: Eth 1/1
  Tunnel index: 3, Tunnel instance: 1, Out label: 2061
 History:
    0  10-13 22:41:58 : LSP tunnel is Enabled
    1  10-13 22:41:58 : CSPF-Computation successful for Primary path path-for-bypass-lsp. Computed route:
                        ->18.29.1.18->18.20.1.20
    2  10-13 22:41:58 : Primary path path-for-bypass-lsp.  RRO received:
                        ->18.29.1.18->18.20.1.20 
    3  10-13 22:41:58 : Primary path path-for-bypass-lsp setup successful . Instance id 1
    4  10-13 22:41:58 : LSP tunnel is UP with Primary path path-for-bypass-lsp as Active
    5  10-13 22:41:58 : Tunnel added or updated, out-interface: Eth 1/1, out-label 2061 
 Riding Backup Lsps: 1
  Ingress backups: 1, up: 1, active: 0
  Transit backups: 0, up: 0, active: 0
  Ingress backups
   State  From            To              LSPname
   UP     18.29.1.29      20.20.20.20     my-fac-bkup-frr-lsp