Message:interface <InterfaceName> is shut down by loop detection (LD)<VLAN ID>
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that a loop has been detected by the loop detection (LD) protocol on the specified interface. The interface has been shut down.
Recommended Action: Identify and fix the Layer 2 bridging loop and then re-enable the interface using the clear loop-detection command.
Message: interface <InterfaceName> is auto-enabled by loop detection (LD).
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the interface on which a loop was detected has been auto-enabled based on the configured shutdown time.
Recommended Action: No action is required.
Message: Loop detected on interface <InterfaceName> vlan <VLAN ID> and no shut down due to shut-down-disabled by loop detection (LD).
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that a loop has been detected by the loop detection (LD) protocol on the specified interface. The interface is not been shut down due to shut-down-disabled (LD) configured on interface.
Recommended Action: loop has been detected and no interface shutdown performed. Check LD shut-down-disabled command under interface.
Message: Loop detected on MCT vlan <VLAN ID> enable loop detection for the VLAN on the peer cluster node.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that a loop has been detected by the loop detection (LD) for MCT VLAN. The interface is not shut down as its used of MCT peer communication.
Recommended Action: Loop has been detected and no interface shutdown performed. Check LD is enabled on the peer MCT node for this VLAN.
Message: Loop is detected on <InterfaceName> <VLAN ID>, the LIF (logical interface) is shutdown.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that a loop has been detected by the loop detection (LD) protocol on the specified interface.
Recommended Action: loop has been detected and shutdown the LIF.
Message: Loop is detected on <InterfaceName> <VLAN ID>, but shutdown action is not performed due to shutdown action is disabled.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that a loop has been detected by the loop detection (LD) protocol on the specified interface.
Recommended Action: do nothing because LIF LD shutdown is disabled.
Message: Loop detection disabled LIF (Logical interface) on <InterfaceName> <VLAN ID> is <HowTo>-enabled.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the interface on which a loop was detected has been auto-enabled based on the configured shutdown time.
Recommended Action: No action is required.
Message: Loop is detected on VxLAN <InterfaceName> <VNI> <VLAN ID>, the LIF (logical interface) is shutdown.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that a loop has been detected by the loop detection (LD) protocol on the specified interface.
Recommended Action: loop has been detected and shutdown the LIF.
Message: Loop is detected on VxLAN <InterfaceName> <VNI> <VLAN ID>, but shutdown action is not performed due to shutdown action is disabled.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that a loop has been detected by the loop detection (LD) protocol on the specified interface.
Recommended Action: do nothing because LIF LD shutdown is disabled.
Message: Loop detection disabled LIF (Logical interface) on VxLAN <InterfaceName> <VNI> <VLAN ID> is <HowTo>-enabled.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the interface on which a loop was detected has been auto-enabled based on the configured shutdown time.
Recommended Action: No action is required.
Message: VxLAN LIF (logical interface) on VxLAN <InterfaceName> <VNI> <VLAN ID> is shutdown by Loop Detection.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that a loop has been detected by the loop detection (LD) protocol, and the VxLAN LIF is shutdown because of it.
Recommended Action: loop has been detected and shutdown the LIF.