Configures the T5 controller‘s interfaces
interface [<WORD>|dsl <1-24>|fe <1-24> <1-2>|ge <1-2>|radio <1-24> <1-2>|vlan <1-4094>]
| <WORD> | Configures the interface identified by the <WORD> keyword |
| dsl <1-24> | Configures the specified DSL interface. A T5 controller uses the IPX operating system to manage its connected radio devices, as opposed to the WiNG operating used by controllers and NX service platforms. However, a T5 controller, once enabled as a supported external device, can provide data to WiNG to assist in a T5‘s management within a WiNG supported subnet populated by both types of devices. The CPEs are the T5 controller managed radio devices using the IPX operating system. These CPEs use DSL as their high speed Internet access mechanism using the CPE‘s physical wallplate connection and phone jack.
|
| fe <1-24> <1-2> | Configures the specified FastEthernet interface. The T5 controller has the following FastEthernet port designations: fe1-fe2 (fe1-fe2 are for up to 24 CPE devices managed by a T5 controller).
In the FastEthernet interface configuration mode, specify the interface settings. |
| ge <1-2> | Configures the specified GigabitEthernet interface. T5 controllers have two Ethernet port designations, These are ge1 and ge2. The GE ports can be RJ-45 or fiber ports supporting 10/100/1000Mbps.
In the GigabitEthernet interface configuration mode, specify the interface settings. |
| radio <1-24> <1-2> | Configures the specified radio interface. T5 controller managed CPE device radios can have their radio configurations overridden once their radios have successfully associated and have been provisioned by the adopting controller, service platform, or peer model AP controller access point.
|
| vlan <1-4094> | Configures the specified VLAN interface. Once configured, the VLAN interface provides layer 3 (IP) T5 controller access or provides layer 3 service on a VLAN. The VLAN interface defines which IP address is associated with each VLAN ID a T5 controller is connected to. A VLAN interface is created for the default VLAN (VLAN 1) to enable remote administration. This interface is also used to map VLANs to IP4 and IPv6 formatted IP address ranges. This mapping determines the destination for routing.
In the VLAN configuration mode, specify the interface‘s primary IP address in the A.B.C.D/M format. Optionally specify the secondary IP address. |
rfs7000-37FABE(config-profile-t5Profile)#interface dsl 1
rfs7000-37FABE(config-profile-t5Profile-if-dsl1)#?
Interface configuration commands:
description Port description
ds-interleaver Enable impulse noise protection in the downstream
direction
ds-max-datarate Configure maximum allowed downstream rate for the
interface
ds-min-margin Configure the minimum downstream signal-to-noise(SNR)
ratio margin
ds-target-margin Configure the desired downstream signal-to-noise (SNR)
ratio margin
duplex Set duplex to interface
flowcontrol Set flowcontrol to interface
line-power Use the line-power command to apply power to the interface
no Negate a command or set its defaults
qos QOS settings
shutdown Shutdown the selected interface
speed Configure speed
switchport Set switching mode characteristics
us-interleaver Enable impulse noise protection in the upstream direction
us-max-datarate Configure maximum allowed upstream rate for the interface
us-min-margin Configure the minimum upstream signal-to-noise (SNR) ratio
margin
us-target-margin Configure the desired upstream signal-to-noise (SNR) ratio
margin
clrscr Clears the display screen
commit Commit all changes made in this session
do Run commands from Exec mode
end End current mode and change to EXEC mode
exit End current mode and down to previous mode
help Description of the interactive help system
revert Revert changes
service Service Commands
--More--
rfs7000-37FABE(config-profile-t5Profile-if-dsl1)#
| no | Removes the selected interface configuration on the T5 device |