AP Inventory Reports

To View Reports:

  1. From the top menu, click Reports.
  2. In the Available AP Reports list, click the report you want to view.
    Note

    Note

    All AP Inventory reports open in a new browser window.
    Note

    Note

    If you open only automatically refreshed reports, the Web management session timer will not be updated or reset. Your session will eventually time out.

The following is an example of the Wireless AP Inventory report:

Click to expand in new window
Graphics/wireless_ap_inventory.png

AP Inventory Report Columns lists the column names and abbreviations found in the AP Inventory report:

Click to expand in new window

AP Inventory Report Columns

Column Name Description
Wireless AP (Serial) Includes AP type, AP name, serial number, and role (including role type)
Topology Ethernet port and associated IP address of the interface on the controller through which the AP communicates.
HW Hardware version of the AP.
SW Software version executing on the AP.
Country Country in which the AP is deployed
Antennas Antennas used
Power Status Indicates ports on the AP39xx with low power status. Feature available for AP39xx only.
Sec. Tunnel Secure tunnel mode
Cert. AP certification (enabled or disabled)
SSH SSH access (enabled or disabled)
LBS Location-based service (enabled or disabled)
Mcast Assembly Multicast Assembly (enabled or disabled)
BD Broadcast disassociation (enabled or disabled).
Persistence Enabled or disabled
P/To Poll timeout. If polling is enabled, a numeric value.
P/I Poll interval. If polling is enabled, a numeric value.
Wired MAC The physical address of the AP's wired Ethernet interface.
Description As defined on the AP Properties screen.
Rdo Radios: 1 or 2.
Ra 802.11a radio. The data entry for an AP indicates whether the a radio is on or off.
Rb 802.11b protocol enabled. Possible values are on or off.
Rg 802.11g protocol enabled. Possible values are on or off.
Rn 802.11n protocol enabled. Possible values are on or off.
DP DTIM period
BP Beacon Period
RT RTS Threshold
FT Fragmentation Threshold
Req Ch Last requested channel
Ch / Tx Current channel Tx power level
Aj Auto Tx Power Ctrl Adjust when ATPC is enabled
TxMn Minimum Tx power, in decibels
TxMx Maximum Tx power, in decibels
ATT Attenuation for APs that support professional antenna installation.
Dom RF domain
MnBR Minimum Basic Rate (For more information, see the Wireless AP radio configuration tabs.)
Pmb Preamble (long, short)
PM Protection Mode
PR Protection Rate
PT Protection Type
VNS Name: MAC Also called BSSID, this is the MAC address of a (virtual) wireless interface on which the AP serves a BSS/VNS. There could be 8 per radio.
11n Channel Width 20MHz, 40MHz, or auto
11n Guard Interval If 11n Channel Width is 40MHz, long or short
11n Channel Bonding Enabled only if 11n Channel Width is 40MHz
11n Protection Mode Protects high throughput transmissions on primary channels from non-11n APs and clients. Enabled or disabled.
Failure Maintn. Maintain MU sessions on the Wireless AP when the AP loses the connection to the controller.
Assn Assignment (address assignment method)
IP Address Wireless AP's IP address if statically configured (same as the Static Values button on the AP Static Configuration screen).
Netmask If the AP's IP address is configured statically, the net mask that is statically configured for the AP.
Gateway If the AP's IP address is configured statically, the IP address of the gateway router that the AP will use.
MTU Interface MTU Interface (enabled or disabled)
MTU Tunnel MTU Tunnel value
TLS 802.1x EAP-TLS authentication configuration
PEAP 802.1x PEAP authentication configuration
EWC Search List The list of IP addresses that the AP is configured to try to connect to in the event that the current connection to the controller is lost.