Extreme SLX-OS Command Reference, 20.7.1 > Commands C - D

Extreme Networks, Inc. March 26, 2025

Search this documentPrint this page

Email this page

View PDF

Previous

Next

Preface
About This Document
- What's New in This Document
- Supported Hardware
Using the SLX-OS CLI
Commands A - B
Commands C - D
Commands E - F
Commands G - J
Commands K - M
Commands N - Q
Commands R - Sh
Show A through Show I
Show J through Show Z
Commands Shu - Z
Commands U - Z

Commands C - D

Section contents:

capability as4-enable
Enables 4-byte autonomous system number (ASN) capability at the BGP global level.
ccm-interval
Sets the time interval between two successive Continuity Check Messages (CCMs) that are sent by Maintenance End Points (MEP) in the specified Maintenance Association (MA).
cee-map
Converged Enhanced Ethernet (CEE) enables you to configure the ETS/CEE parameters including mapping of incoming priorities (traffic with different CoS) to traffic-classes, assigning weights and corresponding bandwidths to those priorities, and scheduling of all occupied traffic-class traffic to egress wire.
certutil import sshkey
Imports an SSH public key for a local SSH user from a remote host using the login credentials and path name.
certutil sshkey
Enters an SSH public key for a specific user by using the command line interface (CLI).
certutil sshx509v3
Configures the SSH user certificate Distinguished Name (DN).
cfm linktrace
Transmits a linktrace message to a Maintenance End Point (MEP) in the domain
cfm loopback
Transmits a loopback message to a specific Maintenance End Point (MEP) or Maintenance Intermediate Point (MIP) in a specified domain.
cfm y1731 domain
Sets the on-demand two-way delay measurement or two-way synthetic loss measurement parameters.
channel-group
Enables link aggregation on an interface.
chassis
Sets the IPv4 or IPv6 address of a device.
cipherset
Configures FIPS-compliant ciphers for the Lightweight Directory Access Protocol (LDAP).
cisco-interoperability
Configures the device to interoperate with some legacy Cisco switches.
class
Creates a class map in a policy map and enters the class map configuration mode.
class-map
Enters class (classification) map configuration mode.
clear arp
Clears some or all Address Resolution Protocol (ARP) entries.
clear bfd neighbors
Clears Bidirectional Forwarding Detection (BFD) neighbors.
clear bgp evpn l2routes
Clears routes from the BGP EVPN Layer 2 route table.
clear bgp evpn local routes
Clears routes from the BGP EVPN local route table.
clear bgp evpn neighbor
Requests a dynamic refresh of BGP EVPN connections or routes from a neighbor, with a variety of options.
clear bgp evpn neighbor dynamic all
Clears all BGP dynamic neighbors in an EVPN address family.
clear bgp evpn routes
Clears routes from the BGP EVPN route table and resets the routes.
clear bgp ip flowspec local
Removes and re-installs local routes for Border Gateway Protocol flow specification (BGP flowspec).
clear bgp ip flowspec neighbor
Removes and re-installs Border Gateway Protocol flow specification (BGP flowspec) information for BGP neighbors.
clear bgp ip flowspec routes
Removes and re-installs Border Gateway Protocol flow specification (BGP flowspec) routes into the hardware.
clear bgp ip neighbor ipv6
Requests a dynamic refresh of Border Gateway Protocol (BGP) connections to IPv4 over IPv6 neighbors.
clear cfm y1731 client-signal-fail statistics
Clears ETH-CSF statistics for all Maintenance Entity Group End Point (MEP) and associated Client interfaces.
clear cfm y1731 statistics
Clears all Y.1731 statistics.
clear cfm y1731 statistics delay-measurement
Clears all Y.1731 statistics for Two-Way ETH-DM.
clear cfm y1731 statistics synthetic-loss-measurement
Clears all Y.1731 statistics for Two-way ETH-SLM.
clear counters
Clears the IP counter statistics on the device.
clear counters access-list
Clears access-control list (ACL) statistical information for a given network protocol and inbound or outbound direction.
clear counters access-list overlay type vxlan
Clears statistics of a specific overlay VXLAN ACL.
clear counters storm-control
Clears all broadcast, unknown unicast, and multicast (BUM) related counters in the system.
clear dot1x statistics
Clears all accumulated dot1x port authentication statistics on the ports.
clear erp statistics
Clears statistics of all Ethernet Ring Protection (ERP) interfaces for all ERP instances, or for a specified instance.
clear erp wtb-time
Clears the Wait to Block (WTB) timer of a specified Ethernet Ring Protection (ERP) protocol instance.
clear erp wtr-time
Clears the Wait to Restore (WTR) timer of a specified Ethernet Ring Protection (ERP) protocol instance.
clear filter-change-update
Clears the filter change update delay period.
clear ip arp inspection statistics
Clears Dynamic ARP Inspection (DAI) statistics for all DAI-enabled VLANs.
clear ip arp suppression-cache
Clears the IPv4 ARP-suppression cache and downloads the current forwarding database from BGP-EVPN. You can also clear the cache for a specified bridge domain or VLAN.
clear ip arp suppression-statistics
Clears ARP suppression statistics. You can also clear statistics for a specified bridge domain or VLAN.
clear ip bgp dampening
Reactivates suppressed BGP4 routes.
clear ip bgp flap-statistics
Clears the dampening statistics for a BGP4 route without changing the dampening status of the route.
clear ip bgp local routes
Clears BGP4 local routes from the IP route table and resets the routes.
clear ip bgp neighbor
Requests a dynamic refresh of BGP4 connections or routes from a neighbor, with a variety of options.
clear ip bgp neighbor dynamic
Clears all dynamic neighbor connections on a device, in a specified VRF, or in a VPNv4 or VPNv5 address family.
clear ip bgp routes
Clears BGP4 routes from the IP route table and resets the routes.
clear ip bgp rpki server
Use this command to stop and restart the RTR library configuration for this particular RPKI server. This command closes the current session and tries to re-establishes connection with the configured RPKI server. The all format of this command closes all sessions and tries to re-establish connections.
clear ip bgp traffic
Clears the BGP4 message counter for all neighbors.
clear ip dhcp relay statistics
Clears IP DHCP Relay statistics.
clear ip dhcp snooping binding
Deletes the specified binding entries from the DHCP snooping binding database.
clear ip flowspec rules statistics
Clears statistics for Border Gateway Protocol flow specification (BGP flowspec) rules.
clear ip igmp groups
Removes the accumulated information about learned groups for a specified VLAN, bridge domain, MCT (Multi-Chassis Trunking) cluster, or CCEP (Cluster Client Edge Port) client.
clear ip igmp statistics
Removes the accumulated IGMP statistics on the specified VLAN or bridge domain.
clear ip multicast snooping mcache
Removes the accumulated information about the multicast forwarding cache for a VLAN or a bridge domain.
clear ip pim mdt
Clears the MDTs maintained by PIM.
clear ip ospf
Clears OSPF data processes, graceful restart, counters, neighbors, or routes.
clear ip route
Clears a specified route or all IP routes in the IP routing tables.
clear ipv6 bgp dampening
Reactivates suppressed BGP4 routes.
clear ipv6 bgp flap-statistics
Clears route-flap statistics for BGP4+ routes.
clear ipv6 bgp local routes
Clears BGP4+ local routes from the IP route table and resets the routes.
clear ipv6 bgp neighbor
Requests a dynamic refresh of BGP4+ connections or routes from a neighbor, with a variety of options.
clear ipv6 bgp neighbor dynamic
Clears all dynamic neighbor connections on a device or all dynamic neighbor connections in a specified VRF.
clear ipv6 bgp routes
Clears BGP4+ routes from the IP route table and resets the routes.
clear ipv6 bgp traffic
Clears the BGP4+ message counter for all neighbors.
clear ipv6 counters
Clears IPv6 counters on all interfaces or on a specified interface.
clear ipv6 dhcp relay delegated-prefixes
Clears IPv6 DHCP delegated prefixes for specific VRF.
clear ipv6 dhcp relay statistics
Clears IPv6 DHCP Relay statistics
clear ipv6 mld groups
Removes the accumulated information about learned groups for a specified bridge domain, VLAN, MCT (Multi-Chassis Trunking) cluster, or CCEP (Cluster Client Edge Port) client.
clear ipv6 mld snooping
Clears the IPv6 multicast snooping database, including entries for MLD snooping and IPv6 PIM snooping, for a VLAN or a bridge domain.
clear ipv6 mld statistics
Removes the accumulated MLD statistics on the specified VLAN or bridge domain.
clear ipv6 multicast snooping mcache
Removes the accumulated information about the multicast forwarding cache for a VLAN or bridge domain.
clear ipv6 nd suppression-cache
Clears the neighbor discovery (ND)-suppression cache. You can also clear the cache for a specified bridge domain or VLAN.
clear ipv6 nd suppression-statistics
Clears suppression statistics for neighbor discovery. You can also clear statistics for a bridge domain or VLAN.
clear ipv6 neighbor
Removes entries from the IPv6 neighbor table.
clear ipv6 ospf
Clears OSPFv3 data processes, graceful restart, counters, force-spf, neighbors, redistribution, routes, and traffic.
clear ipv6 pim mcache
Clears the IPv6 PIM forwarding cache.
clear ipv6 pim rp-map
Clears the RP-to-group mappings in the static IPv6 PIM forwarding table.
clear ipv6 pim traffic
Clears the IPv6 PIM traffic counters.
clear ipv6 route
Clears IPv6 routes.
clear ipv6 vrrp statistics
Clears IPv6 VRRPv3 session statistics for all virtual groups, for a specified interface, or for a specified virtual group.
clear isis all
Clears all IS-IS information.
clear isis counts
Clears IS-IS error statistics for a device.
clear isis database
Clears IS-IS database entries.
clear isis force-spf
Performs the shortest path first (SPF) calculation without clearing the IS-IS database.
clear isis force-v6spf
Performs the IPv6 shortest path first (SPF) calculation without clearing the IS-IS database.
clear isis ipv6 spf-log
Clears IPv6 IS-IS SPF logs.
clear isis neighbor
Clears IS-IS neighbors.
clear isis route
Clears IS-IS routes.
clear isis spf-log
Clears IPv4 IS-IS SPF logs.
clear isis traffic
Clears IS-IS packet counters.
clear lacp
Clears the Link Aggregation Group Control Protocol (LACP) counters on a specific port-channel.
clear lacp counters
Clears the Link Aggregation Group Control Protocol (LACP) counters on all port-channels.
clear link-oam statistics
Clears the Link OAM statistics.
clear lldp neighbors
Clears the Link Layer Discovery Protocol (LLDP) neighbor information on all or specified ethernet interfaces.
clear lldp statistics
Clears LLDP statistics for all interfaces or a specified Ethernet interface.
clear logging raslog
Clears RASLog messages from the router.
clear loop-detection
Enables ports that were disabled by the loop detection (LD) protocol, and clears LD statistics at the global, interface, or VLAN level.
clear loop-detection bridge-domain
Enables ports associated with the bridge domain (BD) that were disabled as part of loop detection, and also clears the LD statistics per BD.
clear mac-address-table
Removes interface entries from the MAC address table.
clear mpls auto-bandwidth-samples
Deletes the sample-history from the auto-bandwidth LSPs.
clear mpls lsp
Allows the user to reset normal LSPs. The user has the option of supplying the primary or secondary parameter for a normal LSP to reset only the primary or secondary path of the LSP.
clear mpls statistics
Clears the MPLS statistics.
clear mvrp statistics
Clears the MVRP statistics for all Ethernet and port-channel interfaces, or for a specific Ethernet or port-channel interface.
clear overlay-gateway
Clear counters for the specified gateway.
clear policy-map-counters
Clears the policy map counters.
clear qos flowcontrol statistics
Clears flow control statistics for a specific interface, port channel, or all interfaces on the device.
clear spanning-tree counter
Clears all spanning-tree counters on an Ethernet or port-channel interface.
clear spanning-tree detected-protocols
Clears all spanning-tree detected protocols on an Ethernet or port-channel interface.
clear statistics bridge-domain
Clears the statistics for all the logical interfaces on bridge domains.
clear statistics vlan
Clears the statistics for all the ports and port channels on configured VLANs.
clear tm voq-stat ingress-device
Clears the traffic management VOQ statistics on the ingress device for a specified Ethernet port, or for all ports.
clear tm voq-stat slot
Clears the traffic management VOQ (virtual output queuing) statistics for one or all CPU group or one or all egress ports.
clear tunnel statistics
Clears statistics from the tunnel interfaces.
clear udld statistics
Clears UDLD statistics.
clear vrrp statistics
Clears VRRP statistics.
CLI
In a Python shell, runs a device CLI command or series of commands. You can also assign the output of such commands to a Python object.
client
Configures a Multi-Chassis Trunking (MCT) client for a cluster and access cluster client configuration mode.
client-interface
Configures a CEP or CCEP interface to the cluster client instance.
client-interface (Y1731)
Associates either a physical interface or a port-channel interface to a Y1731 Maintenance Entity Group End Point (MEP) as a client interface.
client-interfaces-shutdown
Disables the local client interfaces administratively in the cluster to move all traffic on the device to a remote MCT peer device, resulting in failover of traffic to the peer device.
client-pw
Configures the pseudowire (PW) client for an MCT cluster used with VPLS or VLL and access cluster client PW configuration mode.
client-to-client-reflection
Enables routes from one Route Reflector (RR) client to be reflected to other clients by the host device on which it is configured.
clock set
Sets the local clock time and date.
clock timezone
Sets the device system clock time zone options using either Greenwich Mean time (GMT) or one of the US time zones that uses Universal Time Coordinated (UTC) plus or minus a number of hours.
cluster
Configures a Multi-Chassis Trunking (MCT) cluster and access the cluster configuration mode.
cluster-client auto
Configures a Multi-Chassis Trunking (MCT) client for a cluster in auto mode.
cluster-track
Configures interface to track state of MCT cluster.
commit
Use the commit command to commit modifications done to adaptive parameters of a bypass LSP. This command also applies to LSPs. This is not a configuration persistent command; it is a functional command.
compare-med-empty-aspath
Enables comparison of Multi-Exit Discriminators (MEDs) for internal routes that originate within the local autonomous system (AS) or confederation
compare-routerid
Enables comparison of device IDs, so that the path-comparison algorithm compares the device IDs of neighbors that sent otherwise equal-length paths.
confederation identifier
Configures a BGP confederation identifier.
confederation peers
Configures subautonomous systems to belong to a single confederation.
configure terminal
Enters global configuration mode.
config-drift-track
Disables configuration drift detection for the current session.
connector
Accesses connector configuration mode for the ports that support the breakout feature and the insight port feature.
control-word
Enables control word for a pseudowire (PW) profile.
console
Configures the height and width of the serial console terminal.
copy
Copies configuration data.
core-isolation-disable
Core Isolation feature shuts down ESI interface(s) when all the core interfaces between the Leaf and Spine nodes go down. This feature is enabled by default. Use this command to disable this feature. When disabled, the ESI interface will not be brought down when all the core interfaces between the Leaf and Spine go down.
core-isolation-track
Core Isolation feature shuts down ESI interface(s) when all the core interfaces between the Leaf and Spine nodes go down. During core-isolation, data traffic will be black-holed in the multi-homing nodes if the single homed edge port interfaces are present and the Ethernet VPN Instance VLANs are shared with these interfaces. These single homed edge port interfaces need to be brought up/down along with the ESI client interfaces for better data convergence. This command enables tracking these single homed edge port interfaces to ensure that they are brought up/down along with ESI client interfaces.
cos (MPLS)
Configures the a Class of Service (CoS) priority value for all packets traveling through the LSP.
cos (Y1731)
Configures class of service (CoS).
convergence-time
Configures the convergence time when transitioning out of Maintenance Mode. Convergence time comes into play only when Maintenance Mode is disabled.
crypto ca authenticate
Identifies the root CA certificate, which is used to sign the Certificate Signing Request (CSR) to generate the server certificate.
crypto ca enroll
Enrolls the trustpoint by generating the Certificate Signing Request (CSR) and exporting it to the remote certificate server.
crypto ca import
Imports the Identity Certificate for security configuration.
crypto ca import-pkcs
Imports a TLS certificate and a private key in PKCS12 format.
crypto ca trustpoint
Defines the trust point for HTTPS security configuration.
crypto cert expiry-level
Configures generating notifications for certificate expiry. Depending on the number of days to certificate expiry, notifications with different warnings are generated. Notifications can be RASLog or SNMP or both.
crypto import
Imports the Identity Certificate for security configuration.
crypto key
Generates an RSA, ECDSA, or DSA key pair to sign or encrypt and decrypt the security payload during security protocol exchanges for applications. You must sign and encrypt or decrypt the key pair before you obtain a certificate for your device.
csnp-interval
Configures the Complete Sequence Number PDU (CSNP) interval.
cspf-computation-mode
The path calculation metric implementation allows you to specify the path calculation for a given tunnel.
cspf-interface-constraint
Forces the CSPF calculation to include any specified interface when creating an LSP.
cspf-group
Configures a CSPF fate-sharing group by assigning a name to the group.
cspf-group-computation
Use the cspf-group-computation mode when setting up a fate-sharing group.
dampening
Sets dampening parameters for the route in BGP address-family mode.
database-overflow-interval (OSPFv2)
Configures frequency for monitoring database overflow.
database-overflow-interval (OSPFv3)
Configures frequency for monitoring database overflow.
debug access-list-log buffer
Configures or clears the ACL buffer.
debug arp packet buffer
Configures or clears the ARP-packet buffer.
debug dhcp packet buffer
Configures a buffer to capture DHCP packets.
debug dot1x packet
Displays processing information related to IEEE 802.1X port-based access control.
debug ip bgp
Displays information related to the processing of BGP4, with a variety of options.
debug ip bgp neighbor
Displays information related to the processing of BGP4 for a specific neighbor.
debug ip igmp
Enables or disables debugging for IGMP information.
debug ip ospf shortcuts
Enables IP OSPF Shortcuts related debugs in the RAS traces.
debug ip pim
Enables debugging for IP Protocol Independent Multicast.
debug ipv6 bgp
Displays debug information related to BGP processing for IPv6 prefix lists.
debug ipv6 bgp neighbor
Displays debug information related to BGP processing for a specified neighbor.
debug ipv6 dhcp pd
Sets the debugging parameters for the DHCP PD feature.
debug ipv6 mld
Enables IPv6 MLD debug flags.
debug ipv6 ospf graceful-restart
Enables or disables graceful restart debugs for all VRFs or the specified VRF.
debug ipv6 pim
Enables IPv6 PIM debug flags.
debug lacp
Enables or disables debugging for the Link Aggregation Control Protocol (LACP).
debug lldp dump
Dumps debugging information for the Link Layer Discovery Protocol (LLDP) to the console.
debug lldp packet
Enables or disables debugging for the Link Layer Discovery Protocol (LLDP).
debug spanning-tree
Enables debugging for the Spanning Tree Protocol (STP).
debug udld packet
Enables debugging for the Unidirectional Link Detection (UDLD) protocol.
default-information-originate (BGP)
Configures the device to originate and advertise a default BGP route.
default-information-originate (IS-IS)
Generates a default route into an Intermediate System-to-Intermediate System (IS-IS) routing domain.
default-information-originate (OSPFv2)
Controls distribution of default information to an OSPFv2 device.
default-information-originate (OSPFv3)
Controls distribution of default information to an OSPFv3 device.
default-ipv6-gateway
Configures the IPv6 address of the default gateway on a VLAN.
default-link-metric
Configures the metric value globally on all active Intermediate System-to-Intermediate System (IS-IS) interfaces for a specified address family.
default-local-preference
Enables setting of a local preference value to indicate a degree of preference for a route relative to that of other routes.
default-metric (BGP)
Changes the default metric used for redistribution.
default-metric (IS-IS)
Sets the default redistribution metric value for the Intermediate System-to-Intermediate System (IS-IS) routing protocol.
default-metric (OSPF)
Sets the default metric value for the OSPFv2 or OSPFv3 routing protocol.
default-passive-interface
Marks all OSPFv2 and OSPFv3 interfaces passive by default.
delay
For an implementation of an event-handler profile, specifies a delay from when a trigger is received until execution of the event-handler action.
delay-link-event
Configures the port transition hold timer to set a delay in the sending of port up or down port events, or both, to Layer 2 protocols.
delete
Deletes a user-generated file from the flash memory.
delete-packet
Configures the logging or monitoring interval for all Traffic Management (TM) deleted packets on the SLX-OS device.
deploy
Deploys the MCT cluster or cluster client.
description (BD)
Specify a string that contains the description for a bridge-domain or multiple bridge-domains.
description (event-handler)
Defines a description for an event-handler profile.
description (interfaces)
Specify a string that contains the description of a specified interface.
description (LLDP)
Specifies a string that contains the LLDP description.
description (STP)
Describes an xSTP configuration.
description (VRRP)
Describes a Virtual Router Redundancy Protocol extended (VRRP-E) interface.
designated-forwarder-hold-time
Configures the time in seconds to wait before electing a designated forwarder.
destination
Configures the destination address for the tunnel interface.
dhcp ztp cancel
The Zero Touch Provisioning (ZTP) session indefinitely retries detecting the DHCP server to establish a network connection for firmware download. Once canceled, the ZTP session stops retrying.
dhcp ztp log
Displays the Zero Touch Provisioning progress log.
dir
Lists the contents of the device flash memory.
disable-adjacency-check
Disables Intermediate System-to-Intermediate System (IS-IS) IPv6 protocol-support consistency checks that are performed prior to forming adjacencies on hello packets.
disable-incremental-spf-opt
Disables incremental full SPF optimizations for Intermediate System-to-Intermediate System (IS-IS).
disable-inc-stct-spf-opt
Disables incremental shortcut LSP SPF optimization.
disable-partial-spf-opt
Disables partial SPF optimizations for Intermediate System-to-Intermediate System (IS-IS).
disallow-oar-ac
Allows multiple attachment circurit (AC) endpoints on a virtual router interface that is configured for a VPLS instance.
discard-packet
Configures the logging or monitoring interval for all Traffic Management (TM) discarded packets on the SLX-OS device.
discard-voq-packet
Configures the logging interval or threshold for all Virtual Output Queue (VOQ) discarded packets.
distance (BGP)
Changes the default administrative distances for eBGP, iBGP, and local BGP.
distance (IS-IS)
Configures an administrative distance value for Intermediate System-to-Intermediate System (IS-IS) routes.
distance (OSPF)
Configures an administrative distance value for OSPFv2 and OSPFv3 routes.
distribute
Enables advertisement of Border Gateway Protocol flow specification (BGP flowspec) rules that are configured under a route map.
distribute-list prefix-list (OSPFv3)
Applies a prefix list to OSPF for IPv6 routing updates. Only routes permitted by the prefix-list can go into the routing table.
distribute-list route-map
Creates a route-map distribution list.
domain-name
Creates a maintenance domain at a specified level and name and enters the maintenance domain mode specified in the command argument.
dot1ag-compliance
Enables IEEE 802.1ag (Dot1ag) compliance configuration mode to configure left and right interfaces, by associating MD name, MA name, MEP ID, and RMEP ID per interface for both ERP left and right interfaces for signal failure and recovery. This allows MDs, MAs, and MEPs to be configured as part of Dot1ag and to be associated with an Ethernet Ring Protection (ERP) instance to achieve faster convergence.
dot1x authentication
Enables 802.1x authentication on a port.
dot1x enable
Enables 802.1X authentication globally.
dot1x filter-strict-security
Enables or disables strict filter security for dot1x authentication on the interface.
dot1x max-req
Configures the retransmission parameter that defines the maximum number of times EAP request/challenge frames are retransmitted when EAP response/identity frame is not received from the client.
dot1x port-control
Controls port-state authorization and configures the port control type to activate authentication on an 802.1X-enabled interface.
dot1x quiet-period
Configures the time interval that the device remains idle between a failed authentication and a reauthentication attempt.
dot1x reauthenticate
Initiates 802.1X reauthentication on a specified interface.
dot1x reauthentication
Configures the device to periodically reauthenticate the clients connected to 802.1X-enabled interfaces at regular intervals.
dot1x reauthMax
Sets the maximum number of times that a port attempts 802.1x reauthentication before the port changes to the unauthorized state.
dot1x test eapol-capable
Executes the 802.1x readiness check on the switch.
dot1x test timeout
Sets the 802.1X readiness test timeout.
dot1x timeout
Configures the timeout parameters that determine the time interval for client reauthentication and EAP retransmissions.
dpod
Manages Dynamic Ports on Demand (POD) assignments.
dscp (QoS)
Defines the DSCP-to-EXP values for an MPLS QoS DSCP-to-EXP mutation map.
dscp (Tunnel)
Configures the tunnel differentiated services code point (DSCP).
dscp-ttl-mode
Configures tunnel differentiated services code point (DSCP) time to live (TTL) mode.
duplicate-mac-timer (EVPN default instance)
Configures a duplicate MAC detection timer for the detection of continuous MAC moves.
dynamic-bypass
The dynamic-bypass command enables dynamic bypass on a MPLS router or on an Ethernet interface.

9039216-00 Rev AA

Search this documentPrint this page

Email this page

View PDF

Previous

Next

© 2024 Extreme Networks.
Legal
Privacy and Cookies Policy