RF Domain Overrides

Use RF Domain Overrides to define settings overriding a target device‘s original RF Domain configuration. An RF Domain allows an administrator to assign configuration data to multiple access points (of the same model) deployed in a common coverage area (floor, building or site). In such instances, there are many configuration attributes these devices share as their general client support roles are quite similar. However, device configurations may need periodic refinement from their original RF Domain administered design. Unlike a RFS series controller, an access point supports a single RF domain. An access point RF Domain cannot be used on a different model access point. For example, an AP 6532 RF Domain override can only be applied to another AP 6532 model access point.

Go to Configuration → Devices → Device Overrides.

The Device Overrides screen displays. This screen lists devices within the managed network.
Select an access point.

The selected access point's configuration menu displays, with the Basic configuration screen selected by default.
Select RF Domain Overrides.

The RF Domain configuration overrides screen displays.

Access Point - Device Overrides - RF Domain Overrides

Note

A blue override icon (to the left of a parameter) defines the parameter as having an override applied. To remove a device‘s override, go to the Basic Configuration screen‘s Device Overrides field, and then select the Clear Overrides button.

Refer to the Basic Configuration field to review the basic settings defined for the target device‘s RF Domain configuration, and optionally assign/remove overrides to and from specific parameters.


Location	Set the deployment location for the access point as part of its RF Domain configuration
Contact	Set the administrative contact for the access point. This should reflect the administrator responsible for the access point‘s configuration and wireless network.
Time Zone	Use the drop-down menu to select the geographic time zone supporting its deployment location
Country Code	Use the drop-down menu to select the country code supporting its deployment location

Refer to the SMART Scan field to review the settings defined for SMART RF. Optionally assign/remove overrides to and from specific parameters.


Enable Dynamic Channel	Select this option to enable dynamic channel scan.
2.4 GHz Channels	Use the Select drop-down menu to select channels to scan in the 2.4 GHz band. Selected channels are highlighted with a grey background. Unselected channels are highlighted with a white background. Multiple channels can be selected at the same time
5.0 GHz Channles	Use the Select drop-down menu to select channels to scan in the 5.0 GHz band. Selected channels are highlighted with a grey background. Unselected channels are highlighted with a white background. Multiple channels can be selected at the same time

Use the Licenses drop-down menu to obtain and leverage feature licenses from RF Domain member devices.
Refer to the Client Name Configuration table to view the clients connected to RF Domain member access points adopted by networked controllers or service platforms. Use the table to associate administrator assigned client names to specific connected client MAC addresses for improved client management.

Enter the client‘s factory coded MAC address in the MAC Address field. Assign a name to the RF Domain member access point‘s connected client to assist in its easy recognition in the Name field.
Use the Sensor Policy drop-down menu to either select a sensor policy for sending RSSI information to a dedicated ExtremeLocationing system for device locationing calculations. Different policies can be created with either a default set of scanned channels or with custom channels, widths and weighted scan priorities. Specific channels can also be isolated and locked for specific channel scans.

Note

If a dedicated sensor is utilized with WIPS for rogue detection, any sensor policy selected from the Sensor Policy drop-down menu is discarded and not utilized by the sensor. To avoid this situation, use ADSP channel settings exclusively to configure the sensor and not the WiNG interface.

Select the Create icon to create a new sensor policy to apply to this RF Domain or select the Edit icon to update the configuration of an existing policy before applying it to the RF Domain. For more information, see Sensor Policy.

Within a ExtremeLocation Appliance Configuration, sensors scan for RSSI data on an administrator defined interval and send to a dedicated ExtremeLocationing Server resource, as opposed to an ADSP server. Select the + Add Row button to populate the screen with up to three rows for Locationing server credentials.


Server Id	Use the spinner control to assign a numeric ID for up to three ExtremeLocation servers designated to receive RSSI scan data from a WiNG dedicated server. The server with the lowest defined ID is the first reached. The default ID is 1.
IP Address/Hostname	Provide the numeric (non DNS) IP address or hostname of up to three ExtremeLocation server resources for receiving RSSI scan data. A hostname cannot exceed 64 characters or contain an underscore.
Port	Use the spinner control to specify the port of the ExtremeLocation sensor server resource receiving RSSI scan data from a dedicated sensor. The default port is 443.

In the Tenant Id field, enter the ExtremeLocation tenant's account number. Use this field to configure your ExtremeLocation Tenant account number. ExtremeLocation Tenants, at the time of registration, are communicated (via email) an account number uniquely identifying the Tenant. Configure this account number in the RF Domain context. When configured, RF Domain AP reports, pushed to the ExtremeLocation server, include the Tenant's account number along with the reporting AP's MAC address.
Select the Enable NSight Sensor checkbox to enable the NSight module.
Click OK to save the changes to the sensor configuration.

Click Reset to revert to the last saved configuration.