ExtremeXOS 16.1 User Guide

To enable TRILL data plane forwarding on the switch, use the following command:

enable trill

To disable the TRILL protocol on the switch, use the following command:

disable trill

To administratively add a VLAN tag, or a range of VLAN tags that represent edge (or access) VLANs attached to the TRILL network, use the following command:

configure trill add access tag first_tag {- last_tag}

To administratively delete a VLAN tag, or a range of VLAN tags from the configured access VLAN set, use the following command:

configure trill delete access tag first_tag {- last_tag}

To configure the desired VLAN to use as the designated TRILL VLAN, use the following command:

configure trill designated-vlan desired vlan_name

To configure the TRILL protocol on the specified VLAN, use the following command:

configure trill add network vlan vlan_name

To remove TRILL from the specified network VLAN from the TRILL configuration, use the following command:

configure trill delete network vlan [vlan_name | all]

To allocate a nickname for use by the local RBridge, use the following command:

create trill nickname nickname_id {nickname-priority id_priority} {root-priority root_priority} {name nickname_string}

To delete an RBridge nickname, use the following command:

delete trill nickname [nickname_id | nickname_string | all]

To configure the nickname parameters, use the following command:

configure trill nickname [nickname_id | nickname_string] {new-nicknname new_nickname_id} {nickname-priority nickname_id_priority} {root-priority new_root_priority} {name new_nickname_string}

To enable and disable the TRILL Hello protocol per port, use the following command:

configure trill ports [port_list| all] protocol [enable | disable]

To configure the designated RBridge election priority, use the following command:

configure trill ports [port_list | all] {drb-election priority}

To configure the TRILL interface link type for the specified port, use the following command:

configure trill ports [port_list | all] {link-type [broadcast | point-to-point]}

To configure the TRILL link metric for the specified link, use the following command:

configure trill ports [port_list| all] {metric [metric | automatic]}

To configure the RBridge‘s TRILL System ID, use the following command:

configure trill system-id [switch-mac | system_id]

To configure the TRILL link metric for the specified link, use the following command:

configure trill ports [port_list| all] {metric [metric | automatic]}

To configure the RBridge to represent multiple devices on a shared link as being connected to a TRILL pseudonode, use the following command::

configure trill pseudonode [enable | disable]

To configure the amount of time the RBridge does not forward traffic to end stations after detecting a root RBridge topology change, or under certain conditions when the appointed forwarder status changes, use the following command:

configure trill inhibit-time seconds

To enable and disable the RBridge maintenance mode, use the following command:

configure trill maintenance-mode [enable | disable]

To configure the maximum amount of next-hops calculated to an egress RBridge, use the following command:

configure trill sharing max-next-hops max_next_hops

To configure the TRILL MTU size, use the following command:

configure trill mtu size mtu_size

Note

Jumbo frames must be enabled on TRILL Network ports.

To configure the TRILL MTU probe protocol, use the following command:

configure trill mtu probe [enable | disable]

To configure the MTU probe failure count, use the following command:

configure trill mtu probe fail-count probes_sent

To configure tree pruning for all trees in-use as specified by the use count, use the following command:

configure trill tree prune vlans [enable | disable]

To configure the TRILL Link State Protocol timers, use the following command:

To configure the TRILL SPF restart time and periodic calculation intervals, use the following command:

configure trill timers spf {restart restart_interval} {interval seconds}

To configure the TRILL SPF back-off timer delay, use the following command:

configure trill timers spf backoff-delay {minimum minimum_delay} {maximum maximum_delay}

To configure the TRILL Hello protocol timers, use the following command:

configure trill timers hello {multiplier number} {interval [seconds | minimal]}

To set the minimum time between consecutive complete sequence number packet (CSNP) transmissions on the specified interface, use the following command:

configure trill timers csnp {interval seconds}

To display general configuration information related to TRILL, use the following command:

show trill {detail | counters}

To display status information related to RBridges in the TRILL network, use the following command:

show trill rbridges

To display network information related to TRILL RBridge neighbors, use the following command:

show trill neighbor {nickname nickname | system-id system_id | mac-address mac_address}

To display operational TRILL information associated with the switch ports, use the following command:

show trill ports {port_list} {counters {no-refresh | refresh | detail}}

To display the links state database associated with TRILL network, use the following command:

show trill lsdb {lsp-id lsp_id | detail}

To display the egress RBridge forwarding database for the TRILL network, use the following command:

show trill distribution-tree {[pruning vlan | rpf] {dtree_nickname}}

To clear all protocol and port counters associated with TRILL, use the following command:

clear trill counters

To ping a remote RBridge, use the following command:

ping trill {count count} {interval interval} rbridge_nickname

To perform a traceroute to a remote RBridge, use the following command:

traceroute trill rbridge_nickname

To clear the TRILL configuration and remove the TRILL protocol from all VLANs, use the following command:

unconfigure trill

Configuring TRILL