show mac-address-table
Displays MAC address table information.
Syntax
show mac-address-table
bridge-domain
[
id
]
show mac-address-table
cluster
cluster-ID
[
{
bridge-domain
[
bd-ID
]
}
|
[client
client-ID
]
|
client-pw|
local
|
remote
|
[vlan
vlan-ID
]
]
show mac-address-table
count
[
bridge-domain
id
]
show mac-address-table
[
address
mac-address
]
[
aging-time]
|
[dynamic
[address
mac-address
] | [ interface
ethernet
slot/port |
port-channel interface number] |
vlan vlan id]
]
|
[interface
{ethernet
slot/port |
port-channel number} |
tunnel tunnel id]
|
[
mdb [ mac-address] |
client
<client-name> |
vlan
<vlan-id>]]
|
[static [address mac-address] |
[interface
{
ethernet slot/port |
port-channel number
}
]
|
[vlanvlan id]
|
[vlanvlan id]
show
mac-address-table
mac-move
[shut-list
]
Parameters
- bridge-domain
id
- Specifies the displaying of MAC addresses learned under a bridge domain. When a bridge domain identifier is not specified, information is displayed about MAC addresses learned under all bridge domains.
- cluster
cluster-ID
- Displays the MAC addresses learned under the
specified MCT cluster ID.
- bridge-domain
id
- Displays the MAC
addresses learned for the bridge domain of the MCT cluster. When
a bridge domain identifier is not specified, information is
displayed about MAC addresses learned under all bridge domains.
- client
client-ID
- Displays the MAC
addresses learned for the client ID of the MCT cluster.
- client-pw
- Specifies the PW client to display all
the MAC addresses learned from other VPLS PE nodes over MCT
bridge domains. (SLX 9640 and SLX 9540 devices only)
- local
- Displays the
local MAC addresses for the cluster or the specified client ID.
- remote
- Displays the
remote MAC addresses for the cluster or the specified client ID.
- vlan
vlan-ID
- Displays the MAC
addresses for the client VLAN ID of the MCT cluster.
- address
MAC-address
- Displays forwarding information for a 48-bit MAC address. The valid format is
H.H.H (available in Privileged EXEC mode only).
- aging-time
- Displays aging-time.
- dynamic
address
MAC-address
- Specifies the dynamic MAC addresses for an
Ethernet interface, port-channel, or VLAN. The valid format is H.H.H (available in
Privileged EXEC mode only).
- interface ethernet
slot/port
- Specifies the Ethernet interface with a valid
slot number/port number.
- port-channel
number
- Specifies the port channel interface
number.
- vlan
vlan id
- Specifies the VLAN interface. The VLAN ID range is from 1 - 4090.
- tunnel
tunnel id
- Specifies the tunnel interface. The tunnel ID range is from 1 - 100000.
- mdb
MAC-address
- Specifies the MDB information for the cluster client specific macs. The valid format is
H.H.H (available in Privileged EXEC mode only).
- client
client-name
- Displays the client instance. Specify the client name with a maximum of 64 characters.
- static
address mac-address
- Specifies the static MAC address for an
Ethernet interface, port-channel, or VLAN. The valid format is H.H.H (available in
Privileged EXEC mode only).
- mac-move
- Displays all mac-move-detect configuration.
- shut-list
- Displays the interfaces in the shutdown list.
Modes
Privileged EXEC mode.
Usage Guidelines
The MAC Type for an MCT cluster displays the following information:
- On the SLX 9640 and SLX 9540 devices:
- The MAC address over the
CEP AC endpoints or VPLS PW are learned and treated as EVPN local MAC
addresses over a singled-homed edge node. These local addresses are
learned as EVPN and displayed as Dynamic. Corresponding MAC addresses
synchronized to the remote MCT node are displayed as EVPN. The EVPN MAC
addresses are programmed pointing to the MCT PW.
- The VPLS MCT MAC on active PWs
are learned as Dynamic and the corresponding MAC addresses are learned
as EVPN on remote MCT node.
- For the client MAC behavior, MAC addresses are learned as CCL on the local MCT node and CCR on the remote MCT node pointing to the CCEP interface.
- Static MAC addresses configured on CEP AC end points are learned as Static. The corresponding remote MAC addresses are learned as EVPN-Sticky in the remote node.
- For static MAC addresses over client interfaces, Static-CCL and CCR are displayed.
Examples
The following example shows how to display MAC table information for all bridge domains.
device# show mac-address-table bridge-domain
VlanId/BD-Id Mac-address Type State Ports/LIF/peer-ip
629(B) 0011.2222.5555 Dynamic Active eth 1/3.100
629(B) 0011.2222.6666 Dynamic Inactive eth 1/1.500
629(B) 0011.2222.1122 Dynamic Active 10.12.12.12
629(B) 0011.2222.3333 static Inactive po 5.700
629(B) 0011.0101.5555 Dynamic Active eth 1/2.400
Total MAC addresses : 5
The following example shows the number of forwarding entries in the MAC address table for bridge domain 1.
device# show mac-address-table count bridge-domain 1
Total MAC addresses : 5
Example
The following example shows how to display the MAC address table aging time.
device# show mac-address-table aging-time
MAC Aging-time : 300 seconds
Example
The following example shows how to display the MAC address table for an MCT cluster.
device# show mac-address-table cluster 1
Vlan/BD'Id Mac-address Type State Ports
100(V) 0010.a111.aaaa CCL Active ETH3/1
100(V) 0010.a111.aa22 Static-CCL Active ETH3/1
100(V) 0010.a111.bbbb CCR Active ETH3/1
200(V) 003d.a111.1111 Dynamic Active Eth 1/1
200(V) 003d.a111.1122 Static Active Eth 1/1
200(V) 003d.a111.3333 EVPN Active 10.2.2.2
200(V) 003d.a111.3322 EVPN-Static Active 10.2.2.2
Example
The following example shows the mac-address-table information for BGP EVPN Multi-homed
devices.
device# show mac-address-table
Type Code - CCL:Cluster Client Local MAC
CCR:Cluster Client Remote MAC
CR:Cluster Remote MAC
ES:Ethernet Segment
VlanId/BDId Mac-address Type State Ports/LIF/PW/T
30 (V) 0010.9400.0102 EVPN Active Tu 32771 (1.1.1.1)
Tu 32772 (2.2.2.2)
30 (V) 0010.9400.0202 EVPN Active Tu 32771 (1.1.1.1)
30 (V) 0010.9400.0302 EVPN Active Tu 32771 (1.1.1.1)
