show mpls rsvp

Displays the MPLS RSVP information.

Syntax

show mpls rsvp igp-sync [ link [ detail | ip ipv4 addr ] | lsp [ detail | name name ] ]
show mpls rsvp interface [ detail | ethernet slot/port | port-channel number | ve vlan_id ]
show mpls rsvp neighbor [ detail | ipv4 address ]
show mpls rsvp session [ backup | brief | destination | detail | detour | down | egress | extensive | in-interface | ingress | name | out-interface | transit | up | wide ]
show mpls rsvp statistics

Parameters

igp-sync
Displays the RSVP IGP synchonization information.
link
Displays the RSVP IGP synchonization link brief information.
detail
Displays the RSVP IGP synchonization link detailed information.
ip ipv4 addr
Displays the RSVP IGP synchonization specified link information.
lsp
Displays the RSVP IGP synchonization LSP brief information.
detail
Displays the RSVP IGP synchonization LSP detailed information.
name name
Displays the RSVP IGP synchonization specified LSP information.
interface
Displays RSVP interface information.
detail
Displays RSVP interface information in detail.
ethernet slot/port
Displays the specifed RSVP Ethernet information.
port-channel number
Specifies a port-channel.
ve vlan_id
Displays the specified VE information.
neighbor
Displays the RSVP neighbor information.
detail
Displays the RSVP neighbor information in detail.
session
Displays the RSVP session information. For addition information, see the show mpls rsvp session command page.
statistics
Displays the RSVP control packet statistics information.

Modes

Privileged EXEC mode

Usage Guidelines

MPLS is supported on the Extreme 8820, SLX 9740, SLX 9640, and SLX 9540 devices only.

Examples

The following example shows the command using the interface option in the interface mode. 

device(config-if-e1000-0/8)# show mpls interface e0/7
Admin: Up	Oper: Up
  MTU: 1500 bytes
  Maximum BW: 10000000 kbps, maximum reservable BW: 10000000 kbps
  Admin group: 0x00000000
  Reservable BW [priority] kbps:
    [0] 10000000	[1] 10000000	[2] 10000000	[3] 10000000 
    [4] 10000000	[5] 10000000	[6] 10000000	[7] 10000000
  Last sent reservable BW [priority] kbps:
    [0] 10000000	[1] 10000000	[2] 10000000	[3] 10000000 
    [4] 10000000	[5] 10000000	[6] 10000000	[7] 10000000
  Soft Preemption under provisioned BW [priority] kbps: [0] 0	[1] 0	[2] 0	[3] 0
    [4] 0	[5] 0	[6] 0	[7] 0
  LDP tunnel count: 0

The following example shows the command using the interface detail option in the router mpls mode. 

device(config-router-mpls)# show mpls rsvp interface detail

                                            Num of OutSegs	Num of
Interface State MD5  RelMsg Bundle SRefresh Act/Inact/Resv	Preempts/softPrmpt 
e0/1	     Up	   OFF  OFF	   OFF	   OFF	     1/0/1	         2/2
e0/2	     Up	   OFF  OFF	   OFF	   OFF	     0/0/0	         0/0
e0/10	    Dn	   OFF  OFF	   OFF	   OFF	     0/0/0	         0/0
9038039-00 Rev AA