Configuring CLI Logging

Use CLI logging to track all CLI commands executed and for fault management purposes. The CLI commands are logged to the system log file as CLILOG module.

About this task

Note

Note

The platform logs CLILOG and SNMPLOG as INFO. Normally, if you configure the logging level to WARNING, the system skips all INFO messages. However, if you enable CLILOG and SNMPLOG the system logs CLI Log and SNMP Log information regardless of the logging level you configure. This is not the case for other INFO messages.

Procedure

  1. Enter Global Configuration mode:

    enable

    configure terminal

  2. Enable CLI logging:

    clilog enable

  3. Optional: Disable CLI logging:

    no clilog enable

  4. Ensure that the configuration is correct:

    show clilog

  5. View the CLI log:

    show logging file module clilog

Example

Enable CLI logging, and view the CLI log:

Switch:1>enable
Switch:1#configure terminal
Switch:1(config)#clilog enable
Switch:1(config)#show logging file module clilog
CP1  [02/13/13 17:27:25.956] 0x002c0600 00000000 GlobalRouter CLILOG INFO     1 CONSOLE rwa show snmp-server host
CP1  [02/13/13 17:28:10.100] 0x002c0600 00000000 GlobalRouter CLILOG INFO     2 CONSOLE rwa show snmp-server notif
CP1  [02/13/13 17:28:45.732] 0x002c0600 00000000 GlobalRouter CLILOG INFO     3 CONSOLE rwa snmp-server force-trap
CP1  [02/13/13 17:29:30.628] 0x002c0600 00000000 GlobalRouter CLILOG INFO     4 CONSOLE rwa show logging file modug
CP1  [02/14/13 19:39:11.648] 0x002c0600 00000000 GlobalRouter CLILOG INFO     5 CONSOLE rwa ena
CP1  [02/14/13 19:39:13.420] 0x002c0600 00000000 GlobalRouter CLILOG INFO     6 CONSOLE rwa conf t
CP1  [02/14/13 19:49:21.044] 0x002c0600 00000000 GlobalRouter CLILOG INFO     7 CONSOLE rwa filter acl 2 enable
CP1  [02/14/13 19:50:08.540] 0x002c0600 00000000 GlobalRouter CLILOG INFO     8 CONSOLE rwa filter acl 2 type inpo1
CP1  [02/14/13 19:50:38.444] 0x002c0600 00000000 GlobalRouter CLILOG INFO     9 CONSOLE rwa filter acl 2 type inpoe
CP1  [02/14/13 19:50:52.968] 0x002c0600 00000000 GlobalRouter CLILOG INFO    10 CONSOLE rwa filter acl enable 2
CP1  [02/14/13 19:51:08.908] 0x002c0600 00000000 GlobalRouter CLILOG INFO    11 CONSOLE rwa filter acl 2 enable
CP1  [02/15/13 06:50:25.972] 0x002c0600 00000000 GlobalRouter CLILOG INFO    14 CONSOLE rwa ena
CP1  [02/15/13 06:50:30.288] 0x002c0600 00000000 GlobalRouter CLILOG INFO    15 CONSOLE rwa conf t
CP1  [02/15/13 06:50:39.412] 0x002c0600 00000000 GlobalRouter CLILOG INFO    16 CONSOLE rwa show vlan basic
CP1  [02/15/13 06:51:09.488] 0x002c0600 00000000 GlobalRouter CLILOG INFO    17 CONSOLE rwa show isis spbm
CP1  [02/15/13 06:56:00.992] 0x002c0600 00000000 GlobalRouter CLILOG INFO    19 CONSOLE rwa spbm 23 b-vid 2 primar1
CP1  [02/15/13 06:56:59.092] 0x002c0600 00000000 GlobalRouter CLILOG INFO    20 CONSOLE rwa show isis
CP1  [02/15/13 07:10:54.928] 0x002c0600 00000000 GlobalRouter CLILOG INFO    21 CONSOLE rwa show isis interface
CP1  [02/15/13 07:12:33.404] 0x002c0600 00000000 GlobalRouter CLILOG INFO    22 CONSOLE rwa show isis spbm
CP1  [02/15/13 07:45:28.596] 0x002c0600 00000000 GlobalRouter CLILOG INFO    23 CONSOLE rwa ena
CP1  [02/15/13 07:45:30.236] 0x002c0600 00000000 GlobalRouter CLILOG INFO    24 CONSOLE rwa conf t
CP1  [02/15/13 07:46:29.456] 0x002c0600 00000000 GlobalRouter CLILOG INFO    25 CONSOLE rwa interface gigabitEther0
CP1  [02/15/13 07:47:28.476] 0x002c0600 00000000 GlobalRouter CLILOG INFO    26 CONSOLE rwa encapsulation dot1q

--More-- (q = quit)

Variable Definitions

The following table defines parameters for the clilog command.

Variable

Value

enable

Activates CLI logging. To disable, use the no clilog enable command.
9037469-00 Rev AB