show ipv6 interface

Show IPv6 information for all or specific interfaces.

Syntax

show ipv6 interface gigabitethernet [{slot/port[/sub-port][-slot/port[/sub-port]][,...]}]
show ipv6 interface icmpstatistics
show ipv6 interface icmpstatistics gigabitEthernet [{slot/port[/sub-port][-slot/port[/sub-port]][,...]}]
show ipv6 interface icmpstatistics loopback <1-256>
show ipv6 interface icmpstatistics mgmtEthernet
show ipv6 interface icmpstatistics mgmtEthernet mgmt
show ipv6 interface icmpstatistics tunnel <1-2000>
show ipv6 interface icmpstatistics vlan <1-4059>
show ipv6 interface icmpstatistics vrf WORD<1-16>
show ipv6 interface icmpstatistics vrfids WORD<0-512>
show ipv6 interface loopback <1-256>
show ipv6 interface mgmtEthernet
show ipv6 interface mgmtEthernet mgmt
show ipv6 interface statistics
show ipv6 interface statistics gigabitEthernet [{slot/port[/sub-port][-slot/port[/sub-port]][,...]}]
show ipv6 interface statistics loopback <1-256>
show ipv6 interface statistics mgmtEthernet
show ipv6 interface statistics mgmtEthernet mgmt
show ipv6 interface statistics tunnel <1-2000>
show ipv6 interface statistics vlan <1-4059>
show ipv6 interface statistics vrf WORD<1-16>
show ipv6 interface statistics vrfids WORD<0-512>
show ipv6 interface tunnel <1-2000>
show ipv6 interface tunnel vrf WORD<1-16>
show ipv6 interface tunnel vrfids WORD<0-512>
show ipv6 interface vlan [<1-4059>]
show ipv6 interface vrf WORD<1-16>
show ipv6 interface vrfids WORD<0-512>

Command Parameters

gigabitEthernet {slot/port[/sub-port][-slot/port[/sub-port]][,...]}: Displays IPv6 interface information for gigabitEthernet. {slot/port[/sub-port][-slot/port[/subport]][,...]} identifies the slot and port in one of the following formats: a single slot and port (slot/port), a range of slots and ports (slot/port-slot/port), or a series of slots and ports (slot/port,slot/port,slot/port). If your platform supports channelization and the port is channelized, you must also specify the sub-port in the format slot/port/sub-port.
icmpstatistics [gigabitEthernet | mgmtEthernet | tunnel | vlan]: Shows IPv6 ICMP statistics for the interface as follows: gigabitEthernetdisplays interface gigabitEthernet configurations, mgmtEthernet-displays interface mgmtEthernet configurations, tunnel-displays interface tunnel configurations, vlan -displays vlan interface configurations.
loopback <1-256>: Displays the interface loopback configurations.
loopback <1-256>: Identifies a loopback interface.
mgmtEthernet mgmt: Displays IPv6 interface information for the management port.
statistics [gigabitEthernet | mgmtEthernet | tunnel | vlan]: Shows IPv6 interface statistics as follows: gigabitEthernet- displays interface gigabitEthernet configurations, mgmtEthernet-displays interface mgmtEthernet configurations, tunnel- displays interface tunnel configurations, vlan -displays vlan interface configurations.
tunnel <1-2000>: Displays IPv6 interface information for a tunnel. The tunnel ID is expressed as a value from 1 to 2000.
vlan <1-4059>: Specifies the VLAN ID in the range of 1 to 4059. By default, VLAN IDs 1 to 4059 are configurable and the system reserves VLAN IDs 4060 to 4094 for internal use. On switches that support the vrf-scaling and spbm-config-mode boot configuration flags, if you enable these flags, the system also reserves VLAN IDs 3500 to 3998. VLAN ID 1 is the default VLAN and you cannot create or delete VLAN ID 1.
vrf WORD<1-16>: Specifies a VRF name. The VRF parameter is optional.
vrfids WORD<0-512>: Specifies a VRF by ID. The VRF parameter is optional.

Default

None

Command Mode

User EXEC

Usage Guidelines

The mgmtethernet and mgmtethernet mgmt parameters only applies to VSP 8600 Series.