Configure ICL Port Mirroring in a Multi-Tenant Architecture

Procedure

  1. Run the following commands to configure access control list applications on Ethernet or port channel and VLAN or virtual Ethernet: 
    efa tenant epg create --name <epg-name> --tenant <tenant-name>

        --type port-profile
        --po <mirror-source-po-list>
        
        --pp-ipv6-acl-in <acl-name>
        --pp-ip-acl-in <acl-name> --pp-ip-acl-out <acl-name>
  2. Run the following commands to configure a mirror session: 
    efa tenant service mirror session create –name <session-name> --tenant <tenant-name>
    --source {<device-ip>,<eth | po | vlan>,<if-name>}
    --type {<source-device-ip>,<eth | po | vlan>,<source-if-name>:<port-based | flow-based>}

    --destination-type {<source-device-ip>,< eth | po | vlan>,<source-if-name>:<span>}
    --destination {<source-device-ip>,<eth | po | vlan>,<source-if-name> : 
			<destination-device-ip>,<eth | po | vlan>,<destination-if-name}
    --direction {<source-device-ip>,< eth | po | vlan>,<source-if-name> : <tx | rx | both>}


(efa:root)root@node-2:~# efa tenant show
+-------+------+------+------+------+------+-------+----------------------------+-------------------+
|Name   | Type | VLAN | L2VNI|L3VNI | VRF  |Enable |           Ports            |  Mirroring Ports  |
|       |      | Range| Range|Range | Count|BD     |                            |                   |
+-------+------+------+------+------+------+-------+----------------------------+-------------------+
|shared |Shared|      |      |      |   0  |false  |10.20.246.15[0/46-47]       |10.20.246.15[0/31] |
|Tenant |      |      |      |      |      |       |10.20.246.16[0/46-47]       |10.20.246.16[0/31] |
|       |      |      |      |      |      |       |10.20.246.21[0/9-10,0/46-48]|10.20.246.21[0/31] |
|       |      |      |      |      |      |       |10.20.246.22[0/9-10,0/46-48]|10.20.246.22[0/31] |
|       |      |      |      |      |      |       |                            |10.20.246.25[0/31] |
|       |      |      |      |      |      |       |                            |10.20.246.26[0/31] |
+-------+-------+------+------+------+------+-------+----------------------------+-------------------+


(efa:root)root@node 2:~# efa tenant po show
+-------+------+--+------+---+-----------+--------+-------+----------------+-----------+------------+-----------+
|  Name |Tenant|ID|Speed |MTU|Negotiation|Min Link| Lacp  |     Ports      |   State   | Dev State  | App State |
|       |      |  |      |   |           |Count   |Timeout|                |           |            |           |
+-------+------+--+------+---+-----------+--------+-------+----------------+-----------+------------+-----------+
|ten1po1|ten1  |64|10Gbps|   |   active  |   1    |  long |10.20.246.15    |po-created |provisioned |cfg-in-sync|
|       |      |  |      |   |           |        |       |[0/46-47]       |           |            |           |
|       |      |  |      |   |           |        |       |10.20.246.16    |           |            |           |
|       |      |  |      |   |           |        |       |[0/46-47]       |           |            |           |
+-------+------+--+------+---+-----------+--------+-------+----------------+-----------+------------+-----------+
|ten2po1|ten2  |64|10Gbps|   |   active  |   1    |  long |10.20.246.21    |po-created |provisioned |cfg-in-sync|
|       |      |  |      |   |           |        |       |0/9-10,0/46-48] |           |            |           |
|       |      |  |      |   |           |        |       |10.20.246.22|   |           |            |           |
|       |      |  |      |   |           |        |       |[0/9-10,0/46-48]|           |            |           |
+-------+------+--+------+---+-----------+--------+-------+----------------+-----------+------------+-----------+
    Example
    efa tenant epg create –name ten1epg1 –tenant ten1 --type port-profile
         --po ten1po1
         --pp-ipv6-acl-in ext-ipv6-permit-any-mirror-acl
    efa tenant service mirror session create –name mirrorsession1 --tenant ten1
              --source 10.20.246.15,po,ten1po1
              --type 10.20.246.15,po,ten1po1:port-based
              --destination 10.20.246.15,po,ten1po1:10.20.246.15,eth,0/31
              --destination-type 10.20.246.15,po,ten1po1:span
              --direction 10.20.246.15,po,ten1po1:tx
    efa tenant service mirror session create –name mirrorsession2 --tenant ten1
              --source 10.20.246.15,po,ten1po1
              --type 10.20.246.15,po,ten1po1:flow-based
              --destination 10.20.246.15,po,ten1po1:10.20.246.15,eth,0/31
              --destination-type 10.20.246.15,po,ten1po1:span
              --direction 10.20.246.15,po,ten1po1:rx

    efa tenant epg create –name ten1epg2 –tenant ten1 --type port-profile
              --po ten1po2
              --pp-ipv6-acl-in ext-ipv6-permit-any-mirror-acl
    efa tenant service mirror session create –name mirrorsession3 --tenant ten1
               --source 10.20.246.21,po,ten1po2
               --type 10.20.246.21,po,ten1po2:port-based 
               --destination 10.20.246.21,po,ten1po2:10.20.246.21,eth,0/31
               --destination-type 10.20.246.21,po,ten1po2:span
               --direction 10.20.246.21,po,ten1po2:tx
    efa tenant service mirror session create –name mirrorsession4 --tenant ten1
              --source 10.20.246.21,po,ten1po2
              --type 10.20.246.21,po,ten1po2:flow-based
              --destination 10.20.246.21,po,ten1po2:10.20.246.21,eth,0/31
              --destination-type 10.20.246.21,po,ten1po2:span
              --direction 10.20.246.21,po,ten1po2:rx
  3. Verify the switch configuration on the SLX device.
    10.20.246.15
    SLX# show running-config ipv6 access-list
ipv6 access-list extended ext-ipv6-permit-any-mirror-acl
 seq 10 permit ipv6 any any mirror
!
SLX#

SLX# show running-config int po 64
interface Port-channel 64
 mtu 9216
 description MCTPeerInterface
 ip address 10.20.20.3/31
 ipv6 access-group ext-ipv6-permit-any-mirror-acl in
 no shutdown
!
SLX#
    		 10.20.246.16
    SLX# show running-config ipv6 access-list
ipv6 access-list extended ext-ipv6-permit-any-mirror-acl
 seq 10 permit ipv6 any any mirror
!
SLX#

SLX# show running-config int po 64
interface Port-channel 64
 mtu 9216
 description MCTPeerInterface
 ip address 10.20.20.2/31
 ipv6 access-group ext-ipv6-permit-any-mirror-acl in
 no shutdown
!
SLX#
    10.20.246.21
    SLX# show running-config ipv6 access-list
ipv6 access-list extended ext-ipv6-permit-any-mirror-acl
 seq 10 permit ipv6 any any mirror
!
SLX#

SLX# show running-config int po 64
interface Port-channel 64
 mtu 9216
 description MCTPeerInterface
 ip address 10.20.20.3/31
 ipv6 access-group ext-ipv6-permit-any-mirror-acl in
 no shutdown
!
SLX#
    		 10.20.246.22
    SLX# show running-config ipv6 access-list
ipv6 access-list extended ext-ipv6-permit-any-mirror-acl
 seq 10 permit ipv6 any any mirror
!
SLX#

SLX# show running-config int po 64
interface Port-channel 64
 mtu 9216
 description MCTPeerInterface
 ip address 10.20.20.2/31
 ipv6 access-group ext-ipv6-permit-any-mirror-acl in
 no shutdown
!
SLX#
    10.20.246.15
    SLX# show running-config monitor session
monitor session 1
 source port-channel 64 destination ethernet 0/31 direction tx
!
monitor session 2
 source port-channel 64 destination ethernet 0/31 direction rx flow-based
!
SLX# show monitor session 1
Session                : 1
Type                   : SPAN
Description            : [None]
State                  : Enabled
Source Interface       : Po 64 (Up)
Destination Interface  : Eth 0/31 (Down)
Direction              : Tx
Type                   : port-based

SLX# show monitor session 2
Session                : 2
Type                   : SPAN
Description            : [None]
State                  : Enabled
Source Interface       : Po 64 (Up)
Destination Interface  : Eth 0/31 (Down)
Direction              : Rx
Type                   : flow-based
    		 10.20.246.21
    SLX# show running-config monitor session
monitor session 1
 source port-channel 64 destination ethernet 0/31 direction tx
!
monitor session 2
 source port-channel 64 destination ethernet 0/31 direction rx flow-based
!
SLX# show monitor session 1
Session                : 1
Type                   : SPAN
Description            : [None]
State                  : Enabled
Source Interface       : Po 64 (Up)
Destination Interface  : Eth 0/31 (Down)
Direction              : Tx
Type                   : port-based

SLX# show monitor session 2
Session                : 2
Type                   : SPAN
Description            : [None]
State                  : Enabled
Source Interface       : Po 64 (Up)
Destination Interface  : Eth 0/31 (Down)
Direction              : Rx
Type                   : flow-based
9037624-00 RevAA