show mpls rsvp-te lsp ingress

show mpls rsvp-te lsp [ingress {fast-reroute} | ingress_lsp_name | ingress ingress_lsp_name | ingress [destination | origin] ipaddress] {[all-paths | detail] | summary | down-paths {detail}}

Description

Displays information for the specified ingress RSVP-TE LSP.

Syntax Description

fast-reroute Limits the display to only those LSPs with fast reroute protection.
ingress_lsp_name Identifies the ingress LSP for which you want to display information.
destination Displays only those LSPs that terminate at the specified IP address.
origin Displays only those LSPs that originate at the specified IP address.
ipaddress Specifies an IP address for an LSP origin or destination.
all-paths Specifies that the display include all redundant paths.
detail Displays the LSP information in verbose format.
summary Displays only the LSP summary statistics section of the normal display.
down-paths Specifies that the display include only those paths that are operationally down.

Default

N/A.

Usage Guidelines

You can limit the display to egress or transit LSPs with the following command:

show mpls rsvp-te lsp [egress | transit] {fast-reroute} {{lsp_name} {[destination | origin]ipaddress} {detail} | summary}

You can display information for all LSPs with the following command:

show mpls rsvp-te lsp {{[destination | origin] ipaddress} {fast-reroute} {detail} | summary}

When label recording is enabled for an LSP, labels are displayed only for the ingress node (the egress label from the previous node always matches the ingress node label).

Example

Use the following command to display information about a specific LSP:

# show mpls rsvp-te lsp jefflsp1
Ingress LSP Name Path Name        Destination     Next Hop I/F     UpTm Flags
---------------- ---------------- --------------- ---------------- ---- --------
jefflsp1         jeffpath1        11.100.100.204  n/a                 0 --PR--IV
Flags: (U) Up, (E) Enabled, (P) Primary LSP, (S) Secondary LSP,
(F) FRR Primary LSP  (R) Redundant Paths, (B) Bandwidth Requested,
(O) ERO Specified,   (I) IP Traffic Allowed, (V) VPN Traffic Allowed,
(v) VPN Assigned Traffic Allowed
Summary of Ingress RSVP-TE LSPs named jefflsp1
Ingress LSPs (Enabled/Disabled)       : 1 (0/1)
Ingress LSPs with no configured path  : 0
Ingress LSP Paths (Up/Down)           : 2 (0/2)

Use the following command to display detailed information about a specific ingress LSP:

# show mpls rsvp-te lsp ingress "lsp598" detail
Ingress LSP Name: lsp598
Destination  : 11.100.100.8           Admin Status : Enabled
IP Traffic   : Allow                  #VPLS Cfgd   : 0
VPN Traffic  : Allow                  #VPLS In-Use : 0
Path Name: path598
Profile Name : prof598
Tunnel ID    : 1                  Ext Tunnel ID  : 11.100.100.20
LSP ID       : 0                  State Changes  : 5
Oper Status  : Enabled            Bandwidth Cfgd : False
LSP Type     : Primary
Activity     : Active
Failures     : 2                  Retries-since last failure : 0
Retries-Total : 12
Rcv Label    : 0x0052e            UpTime         : 0d:0h:3m:44s
Next Hop     : 11.121.96.5
Tx I/F       : 11.121.96.20 - vlan1
Record Route : Indx  IP Address
:    1  11.121.96.5
:    2  11.95.96.9
:    3  11.98.96.8

Use the following command to display detailed information about all paths for an LSP:

# show mpls rsvp-te lsp jefflsp1 all-paths
Ingress LSP Name Path Name        Destination     Transmit I/F     UpTm Flags
---------------- ---------------- --------------- ---------------- ---- --------
jefflsp1         jeffpath0        11.100.100.204  n/a                 0 --SR--IV
jefflsp1         jeffpath1        11.100.100.204  n/a                 0 --PR--IV
Flags: (U) Up, (E) Enabled, (P) Primary LSP, (S) Secondary LSP,
(F) FRR Primary LSP  (R) Redundant Paths, (B) Bandwidth Requested,
(O) ERO Specified,   (I) IP Traffic Allowed, (V) VPN Traffic Allowed,
(v) VPN Assigned Traffic Allowed
Summary of Ingress RSVP-TE LSPs named jefflsp1
Ingress LSPs (Enabled/Disabled)       : 1 (0/1)
Ingress LSPs with no configured path  : 0
Ingress LSP Paths (Up/Down)           : 2 (0/2)

Use the following command to display information about all ingress down paths:

# show mpls rsvp-te lsp ingress down-paths
Ingress LSP Name Path Name        Destination     Transmit I/F     UpTm Flags
---------------- ---------------- --------------- ---------------- ---- --------
jefflsp1         jeffpath0        11.100.100.204  n/a                 0 --SR--IV
jefflsp1         jeffpath1        11.100.100.204  n/a                 0 --PR--IV
jefflsp2         jeffpath2        11.100.100.203  n/a                 0 -EPR-OIV
Flags: (U) Up, (E) Enabled, (P) Primary LSP, (S) Secondary LSP,
(F) FRR Primary LSP  (R) Redundant Paths, (B) Bandwidth Requested,
(O) ERO Specified,   (I) IP Traffic Allowed, (V) VPN Traffic Allowed,
(v) VPN Assigned Traffic Allowed
Summary of Ingress RSVP-TE LSPs
Ingress LSP Paths that are Down       : 3

History

This command was first available in ExtremeXOS 11.6.

This command and its output were modified, and the summary option was added in ExtremeXOS 12.0.

The command output was modified in ExtremeXOS 12.2.2.

Platform Availability

This command is available only on the platforms that support MPLS as described in the Switch Engine 32.3 Feature License Requirements document.