Refer to the following (read only) information to assess logged diagnostic events.
|
Event |
Description |
|---|---|
|
ADOPT-SERVICE SNMP_SUCCESS 6 |
SNMP framework success |
|
ADOPT-SERVICE SNMP_FAILURE 6 |
SNMP framework failure |
|
ADOPT-SERVICETUT_TEMPERATURE_ALARM_RAISED ([str]) |
Temperature alarm raised on sensor |
|
ADOPT-SERVICE TUT_TEMPERATURE_ALARM_CLEARED ([str]) |
Temperature alarm cleared on sensor |
|
ADOPT-SERVICE TUT_TEMPERATURE_ALARM_CLEARED ([str]) |
Temperature alarm cleared on sensor |
|
ADOPT-SERVICE TUT_FAN_ALARM_CLEARED 5 IPX ([str]) |
Fan alarm cleared on ID |
|
ADOPT-SERVICE TUT_PWRCTRL_ALARM_RAISED 5 IPX ([str]) |
Power controller alarm raised |
|
ADOPT-SERVICE TUT_PWRCTRL_ALARM_CLEARED 5 IPX ([str]) |
Power controller alarm cleared |
|
ADOPT-SERVICE TUT_LINE_POWER_ALARM_RAISED 5 IPX ([str]) Line power alarm raised on id [str] |
Line power alarm raised |
|
ADOPT-SERVICE TUT_LINE_POWER_ALARM_CLEARED 5 IPX ([str]) Line power alarm cleared on id [str] |
Line power alarm cleared |
|
ADOPT-SERVICE TUT_WLAN_CLIENT_ASSOC 6 IPX ([str]) Client [str] on interface index [str] associated |
Client associated |
|
ADOPT-SERVICE TUT_WLAN_CLIENT_DISASSOC 6 IPX ([str]) Client [str] on interface index [str] disassociated with status code [str], [str] |
Client disassociated |
|
ADOPT-SERVICE TUT_WLAN_CLIENT_ASSOC_FAILURE 3 IPX ([str]) Association failed for Client [str] on interface index [str] with status code [str], [str] |
Association failed for client on specified interface index |
|
ADOPT-SERVICE TUT_WLAN_CLIENT_AUTH 6 IPX ([str]) |
Client on interface index authenticated |
|
ADOPT-SERVICE TUT_WLAN_CLIENT_DEAUTH 6 IPX ([str]) |
Client on interface index deauthenticated with status code |
|
ADOPT-SERVICE TUT_WLAN_CLIENT_AUTH_FAILURE 3 IPX ([str]) |
Authentication failed for client on interface index with status code |
|
ADOPT-SERVICE TUT_RADIO_ADAPTIVE_POWER_CHANGE 5 IPX ([str]) |
Interface with operational status and power levels |
|
ADOPT-SERVICE TUT_RF_MONITOR_MODE_CHANGE 5 IPX ([str]) |
RF monitor status changed to on interface |
|
ADOPT-SERVICE IPX_EVENT_FAILURE 3 IPX ([str]) |
Failed to raise WiNG event |
|
AP NO_IMAGE_FILE [str] firmware image is not present on controller |
Access Point firmware not on controller |
|
AP IMAGE_PARSE_FAILURE Format of [str] firmware image on controller is invalid |
Invalid Access Point firmware file |
|
AP LEGACY_AUTO_UPDATE Legacy Access Point [str] [mac] being updated |
Legacy Access Point updated |
|
AP AP_ADOPTED [str] [mac] adopted |
Access Point adopted |
|
AP AP_UNADOPTED [str] [mac] un-adopted |
Access Point unadopted |
|
AP AP_RESET_DETECTED 6 [str] [mac] reset itself |
Access Point reset detected |
|
AP AP_RESET_REQUEST 6 [str] [mac] reset request |
Access Point user requested reset |
|
AP AP_TIMEOUT 6 str] [mac] timed out, reset sent to AP |
Access Point timed out |
|
AP ADOPTED Access Point([qstr]/[qstr]/[dev]) at rf-domain:[qstr] adopted and configured. Radios: Count=[str], Bss: [str] |
Access Point adopted and configured |
|
AP UNADOPTED Access Point([qstr]/[qstr]/[dev]) at rf-domain:[qstr] unadopted. Radios: Count=[str], Bss: [str] |
Access Point unadopted |
|
AP ADOPTED_TO_CONTROLLER Joined successfully with controller [qstr]([str]) |
Access Point adopted to controller |
|
AP ONLINE Access Point [dev] is now online. Offline Reason is [str]. Offline count is [int] |
Access Point online |
|
AP OFFLINE Access Point [dev] is now offline. Offline Reason is [str]. Offline count is [int] |
Access Point offline |
|
AP OFFLINE Device [dev]([str]) is offline, last seen:[int] minutes ago on switchport [str] |
Adopted device offline |
|
AP RESET Reset Access Point mac [dev], [str] |
Access Point reset |
|
AP ADOPTION_REDIRECTED Access Point([qstr]/[qstr]/[dev]) cdp:[qstr] lldp:[qstr] redirected to the controller host/pair [qstr] - [qstr] |
Access Point redirected |
|
AP AP_AUTOUP_TIMEOUT 4 AUTOUPGRADE: [str] mac [str] Autoupgrade timed out |
Time out while auto upgrading an AP |
|
AP AP_AUTOUP_REBOOT 5 AUTOUPGRADE: [str] mac [str] Autoupgrade rebooting |
Rebooting AP after upgrade |
|
AP AP_AUTOUP_NO_NEED 6 AUTOUPGRADE: [str] mac [str] ver [str] Autoupgrade not required or not available |
Auto upgrade not initiated |
|
AP AP_AUTOUP_NEEDED 6 AUTOUPGRADE: [str] mac [str] ver [str] Autoupgrade will be applied |
Auto upgrade is initiated on AP |
|
AP AP_AUTOUP_DONE 5 AUTOUPGRADE: [str] mac [str] Autoupgrade complete |
Auto upgrade successful |
|
AP AP_AUTOUP_FAIL 4 AUTOUPGRADE: [str] mac [str] Autoupgrade failed |
Failed auto upgrade attempt |
|
AP AP_AUTOUP_VER 6 AUTOUPGRADE: version [str] available for [str] equipment |
Available Access Point firmware versions for auto upgrade |
|
AAA RADIUS_DISCON_MSG Received Radius dynamic authorization Disconnect Message for [qstr] from server [qstr] |
Received RADIUS disconnect request |
|
AAA RADIUS_VLAN_UPDATE6 Assigning Radius server specified vlan [uint] to client [qstr] on wlan [qstr] |
Client VLAN updated by RADIUS |
|
AAA RADIUS_SESSION_NOT_STARTED5 Radius server indicates session time has not started for client [qstr] |
Start time from RADIUS resource not yet valid |
|
AAA RADIUS_SESSION_EXPIRED5 Radius server indicates session has already expired for client [qstr] |
Session time from RADIUS resource already expired |
|
ADV-WIPS ADV-WIPS-EVENT-1 4 Detected DoS Deauthentication attack against [mac] [str] |
DoS Deauthentication attack |
|
ADV-WIPS ADV-WIPS-EVENT-2 4 Detected DoS Disassociation attack against [mac] [str] |
DoS disassociation attack |
|
ADV-WIPS ADV-WIPS-EVENT-3 4 Detected DoS EAP failure spoof attack by [mac] [str] |
EAP failure spoof attack |
|
ADV-WIPS ADV-WIPS-EVENT-10 4 Detected ID-Theft out of sequence attack for [mac] [str] |
ID theft out of sequence attack |
|
ADV-WIPS ADV-WIPS-EVENT-11 4 Detected possible ID-Theft EAPoL Success spoof attack by [mac] [str] |
Possible ID theft EAPoL success spoof attack |
|
ADV-WIPS ADV-WIPS-EVENT-12 4 Detected possible WLAN-Jack attack by [mac] [str] |
Possible WLAN jack attack |
|
ADV-WIPS ADV-WIPS-EVENT-13 4 Detected possible ESSID-Jack attack against [mac] [str] |
Possible ESSID jack attack |
|
ADV-WIPS ADV-WIPS-EVENT-14 4 Detected possible Monkey-Jack attack by [mac] [str] |
Possible monkey jack attack |
|
ADV-WIPS ADV-WIPS-EVENT-16 4 Detected possible NULL Probe Response attack by [mac] [str] |
Possible NULL probe response attack |
|
ADV-WIPS ADV-WIPS-EVENT-105 4 Sanctioned MU [mac] detected associated with unsanctioned/neighboring AP [str] |
Sanctioned MU detected associated with unsanctioned/neighboring AP |
|
ADV-WIPS ADV-WIPS-EVENT-109 4 Multicast all systems traffic found from [mac] [str] |
Multicast all systems traffic |
|
ADV-WIPS ADV-WIPS-EVENT-110 4 Multicast all routers traffic found from [mac] [str] |
Multicast all routers traffic |
|
ADV-WIPS ADV-WIPS-EVENT-111 4 Multicast OSPF all traffic found from [mac] [str] |
Multicast OSPF all traffic |
|
ADV-WIPS ADV-WIPS-EVENT-112 4 Multicast OSPF Deisgnated Routers traffic found from [mac] [str] |
Multicast OSPF designated routers traffic |
|
ADV-WIPS ADV-WIPS-EVENT-113 4 Multicast RIP-2 Routers traffic found from [mac] [str] |
Multicast RIP 2 routers traffic |
|
ADV-WIPS ADV-WIPS-EVENT-114 4 Multicast IGRP Routers traffic found from [mac] [str] |
Multicast IGRP routers traffic |
|
ADV-WIPS ADV-WIPS-EVENT-115 4 Multicast DHCP Server Relay Agent traffic found from [mac] [str] |
Multicast DHCP server relay agent traffic |
|
ADV-WIPS ADV-WIPS-EVENT-116 4 Multicast VRRP Agent traffic found from [mac] [str] |
Multicast VRRP agent traffic |
|
ADV-WIPS ADV-WIPS-EVENT-117 4 Multicast HSRP Agent traffic found from [mac] [str] |
Multicast HSRP agent traffic |
|
ADV-WIPS ADV-WIPS-EVENT-118 4 Multicast IGMP traffic found from [mac] [str] |
Multicast IGMP traffic |
|
ADV-WIPS ADV-WIPS-EVENT-119 4 Detected NETBIOS traffic from [mac] [str] |
Detected NETBIOS traffic |
|
ADV-WIPS ADV-WIPS-EVENT-120 4 Detected STP traffic from [mac] [str] |
Detected STP traffic |
|
ADV-WIPS ADV-WIPS-EVENT-113 4 Multicast RIP-2 Routers traffic found from [mac] [str] |
Multicast RIP 2 routers traffic |
|
ADV-WIPS ADV-WIPS-EVENT-121 4 Detected IPX traffic from [mac] [str] |
Detected IPX traffic |
|
ADV-WIPS ADV-WIPS-EVENT-142 4 Detected possible Probe Response attack by [mac] [str] |
Possible probe response attack |
|
ADV-WIPS ADV-WIPS-EVENT-221 4 Detected Invalid Management Frames from [mac] [str] |
Invalid management frames |
|
ADV-WIPS ADV-WIPS-EVENT-26 4 Detected DoS RTS flood attack against [mac] [str] |
DoS RTS flood attack |
|
ADV-WIPS ADV-WIPS-EVENT-222 4 Detected Invalid Channel Advertisement for [mac] [str] |
Invalid channel advertisement |
|
ADV-WIPS ADV-WIPS-EVENT-63 4 Detected Windows ZERO Configuration Memory Leak on [mac] [str] |
Windows ZERO configuration memory leak |
|
ADV-WIPS ADV-WIPS-EVENT-220 4 Detected Unauthorized Bridge [mac] [str] |
Unauthorized bridge |
|
AP SW_CONN_LOST 0 Lost connectivity with controller after config update. Rebooting and reverting to older working configuration |
Controller connectivity lost |
|
AAA RADIUS_DISCON_MSG5 Received Radius dynamic authorization Disconnect Message for [qstr] from server [qstr] |
Received RADIUS disconnect request |
|
AAA RADIUS_VLAN_UPDATE6 Assigning Radius server specified vlan [uint] to client [qstr] on wlan [qstr] |
Client VLAN updated by RADIUS resource |
|
AAA RADIUS_SESSION_NOT_STARTED5 Radius server indicates session time has not started for client [qstr] |
Start time from RADIUS resource not yet valid |
|
AAA RADIUS_SESSION_EXPIRED5 Radius server indicates session has already expired for client [qstr] |
Session time from RADIUS resource already expired |
|
CAPTIVE-PORTAL AUTH_SUCCESS6 Captive-portal authentication success for client [mu] ([qstr-ip]) user [qstr] |
Authentication sucess |
|
ADV-WIPS ADV-WIPS-EVENT-26 4 Detected DoS RTS flood attack against [mac] [str] |
DoS RTS flood attack |
|
ADV-WIPS ADV-WIPS-EVENT-222 4 Detected Invalid Channel Advertisement for [mac] [str] |
Invalid channel advertisement |
|
ADV-WIPS ADV-WIPS-EVENT-63 4 Detected Windows ZERO Configuration Memory Leak on [mac] [str] |
Windows ZERO configuration memory leak |
|
ADV-WIPS ADV-WIPS-EVENT-220 4 Detected Unauthorized Bridge [mac] [str] |
Unauthorized bridge |
|
AP SW_CONN_LOST 0 Lost connectivity with controller after config update. Rebooting and reverting to older working configuration |
Controller connectivity lost |
|
AAA RADIUS_DISCON_MSG5 Received Radius dynamic authorization Disconnect Message for [qstr] from server [qstr] |
Received RADIUS resource disconnect request |
|
AAA RADIUS_VLAN_UPDATE6 Assigning Radius server specified vlan [uint] to client [qstr] on wlan [qstr] |
Client VLAN updated by RADIUS |
|
AAA RADIUS_SESSION_NOT_STARTED5 Radius server indicates session time has not started for client [qstr] |
Start time from RADIUS resource not yet valid |
|
AAA RADIUS_SESSION_EXPIRED5 Radius server indicates session has already expired for client [qstr] |
Session time from RADIUS resource already expired |
|
CAPTIVE-PORTAL AUTH_SUCCESS6 Captive-portal authentication success for client [mu] ([qstr-ip]) user [qstr] |
Authentication success |
|
CAPTIVE-PORTAL AUTH_FAILED6 Captive-portal authentication failed for client [mu] ([qstr-ip]) |
Authentication failed |
|
CAPTIVE-PORTAL SESSION_TIMEOUT6 Captive-portal session timed out for client [mu] ([qstr-ip]) |
Session timed out |
|
CAPTIVE-PORTAL CLIENT_DISCONNECT 6 Captive-portal session disconnected for client [mu] ([qstr-ip]) |
Client disconnected |
|
CAPTIVE-PORTAL PURGE_CLIENT6 Captive-portal: Purge client [mu] by new client [mu] for user [qstr] |
Client purged |
|
CAPTIVE-PORTAL FLEX_LOG_ACCESS 6 [qstr]: [qstr] allowed access for client [mu] ([qstr-ip]) |
Flex log access granted for client |
|
CAPTIVE-PORTAL INACTIVITY_TIMEOUT 6 Captive-portal session cleared for client [mu] ([qstr-ip]) after inactivity timeout |
Client timed out due to inactivity |
|
CAPTIVE-PORTAL ALLOW_ACCESS6 Captive-portal allow access for client [mu] ([qstr-ip]) |
Client allowed access |
|
CAPTIVE-PORTAL CLIENT_REMOVED6 Captive-portal session removed for client [mu] ([qstr-ip]) on policy change/admin action |
Client removed due to admin changes |
|
CAPTIVE-PORTAL PAGE_CRE_FAILED3 Page creation failed for policy [qstr], file [qstr], Error [qstr] |
Page creation failure |
|
CAPTIVE-PORTAL DATA_LIMIT_EXCEED6 Data limit exceed, Usage:[int] KBytes, Action:[str], client [mu] ([ip]) |
Client data limit exceeded |
|
CAPTIVE-PORTAL VLAN_SWITCH6 Client [mu] ([ip]) switching from vlan [int] to vlan [int] |
Client VLAN switch |
|
CAPTIVE-PORTAL SERVER_MONITOR_STATE_CHANGE6 Captive-portal policy [qstr]: service monitor [str] server status changing from [qstr] to [qstr] |
Captive portal server monitor state changed |
|
CAPTIVE-PORTAL NO_SERVICE_PAGE_SENT6 Captive-portal sent no service page to client [mu] ([ip]) as [str] server is down |
No service page sent to client |
|
CERTMGR RSA_KEY_ACTIONS_SUCCESS 6 [str] of RSA key [str] successful |
Successful completion of RSA key related actions (import, export etc.) |
|
CERTMGR RSA_KEY_ACTIONS_FAILURE 3 [str] of RSA key [str] failed: [str] |
Failure of RSA key related actions (import, export etc.) |
|
CERTMGR CA_CERT_ACTIONS_SUCCESS 6 [str] of CA certificate for trustpoint [str] successful |
Successful completion of CA certificate related actions (import, export etc.) |
|
CERTMGR CA_CERT_ACTIONS_FAILURE 3 [str] of CA certificate for trustpoint [str] failed: [str] |
Failure of CA certificate actions (import, export etc.) |
|
CERTMGR SRV_CERT_ACTIONS_SUCCESS 6 [str] of Server Certificate of trustpoint [str] successful |
Successful completion of server certificate actions (import, export etc.) |
|
CERTMGR SVR_CERT_ACTIONS_FAILURE 3 [str] of Server Certificate of trustpoint [str] failed: [str] |
Failure of server certificate actions (import, export etc.) |
|
CERTMGR CSR_EXPORT_SUCCESS 6 Export of Certificate Signing Request for [str] successful |
Successful export of certificate signing request |
|
CERTMGR CSR_EXPORT_FAILURE 3 Export of Certificate Signing Request for [str] failed: [str] |
Failed to export certificate signing request |
|
CERTMGR CRL_ACTIONS_SUCCESS 6 [str] of CRL for trustpoint [str] successful |
Successful completion of certificate revocation list action |
|
CERTMGR CRL_ACTIONS_FAILURE 3 [str] of CRL for trustpoint [str] failed: [str] |
Certificate revocation list action failure |
|
CERTMGR DELETE_TRUSTPOINT_ACTION 6 Deletion of trustpoint [str] successful |
Deletion of trustpoint |
|
CERTMGR IMPORT_TRUSTPOINT 6 Import of Trustpoint [str] [str] |
Import of trustpoint |
|
CERTMGR EXPORT_TRUSTPOINT 6 Export of Trustpoint [str] [str]// |
Export of trustpoint |
|
CERTMGR CERT_EXPIRY 4 [str] certificate for trustpoint [str] [str] |
Certificate expiration |
|
CERTMGR CA_KEY_ACTIONS_SUCCESS 6 [str] of CA private key for trustpoint [str] successful |
Successful completion of CA private key actions |
|
CERTMGR CA_KEY_ACTIONS_FAILURE 3 [str] of CA private key for trustpoint [str] failed: [str] |
Failure of CA private key actions |
|
CLUSTER CMASTER_CFG_UPDATE_FAIL 3 Cluster master config update to [str] failed, Err: [str] |
Cluster master config update failed |
|
CLUSTER MAX_EXCEEDED 4 Max cluster members ([uint]) exceeded, clustering will not function properly until corrected |
Max cluster count exceeded |
|
CLUSTER STATE_CHANGE 4 Active cluster member changed. Present active [str]. Previous active [str]. |
Active cluster membership change |
|
CLUSTER STATE_CHANGE_INACTIVE 4 Member [str] (load[int]) changing state from Active to Standby. New member [str] standby load [int]. |
Cluster member change from active to standby |
|
CLUSTER STATE_CHANGE_ACTIVE 4 Member [str] (load[int]) changing state from Standby to Active. New member [str] standby load [int] |
Cluster member change from standby to active |
|
CLUSTER STATE_RETAIN_ACTIVE 4 Member [str] (load[int]) retaining Active state. New member [str] standby load [int] |
Cluster member retaining active state |
|
CRM CRITICAL_RESOURCE_UP5 Critical Resource [str] is UP |
Critical resource is up |
|
CRM CRITICAL_RESOURCE_DOWN 5 Critical Resource [str] is DOWN |
Critical resource is down |
|
CERTMGR-LITE INVALIDCACERT 5 CA Certificate imported for the trustpoint [str] is invalid |
CA certificate is invalid |
|
CERTMGR-LITE INVALIDSERVCERT 5 Server Certificate imported for the trustpoint [str] is invalid |
Server certificate is invalid |
|
CERTMGR-LITE INVALIDCERTCRL 5 Certificate Crl Imported for trustpoint [str] is invalid |
CRL is invalid |
|
CERTMGR-LITE CERTEXPIRED 5 [str] Certificate of trustpoint [str] is expired// |
Certificate is expired |
|
CERTMGR-LITE INVALIDCERTKEY 5 Private key imported for trustpoint [str] is not valid |
Private key is invalid |
|
CERTMGR-LITE INVALIDRSAKEY 5 Rsakey imported is not valid [str] is invalid// |
RSA key import operation |
|
CERTMGR-LITE KEYDECRYPTFAILE 4 Rsakey cannot be decrypted with the password provided |
RSA key cannot be decrypted with provided password |
|
CERTMGR-LITE CERTIMPORTED 6 [str] Certificate imported for the trustpoint [str] |
Certificate imported for trustpoint |
|
CERTMGR-LITE CERTKEYIMPORTED 6 Private key imported for the trustpoint [str] |
Private key imported for trustpoint |
|
CERTMGR-LITE RSAKEYIMPORTED 6 Rsakey imported with the name [str] |
RSA key imported |
|
CERTMGR-LITE DELETETRUSTPOINT 6 Trustpoint [str] is deleted |
Trustpoint deleted |
|
CERTMGR-LITE DELETERSAKEY 6 Rsakey [str] is deleted |
RSA Key deleted |
|
CERTMGR-LITE CERTREQUESTGEN 6 Certificate request generated for the trustpoint [str] |
Certificate requested generated |
|
CERTMGR-LITE CERTSELFSIGNEDGEN 6 Selfsigned certificate generated for the trustpoint [str] |
Self signed certificate generated |
|
CERTMGR-LITE RSAKEYGEN 6 Rsa key [str] generated |
RSA key generated |
|
CERTMGR-LITE ERROR 5 [str] |
Certificate manager general error |
|
CERTMGR-LITE CERT_EXPIRY4 [str] certificate for trustpoint [str] [str] |
Certificate about to expire |
|
CERTMGR CERT_RENEW_FAILED1 Certificate renew in field failed reason [str] |
Certificate renew failure reason |
|
DHCPSVR DHCPSVR_STOP 6 DHCP server is stopped |
DHCP server stopped |
|
DIAG WD_RESET_SYS 2 The system has been RESET by the Watchdog |
Log watchdog reset |
|
DIAG CPU_USAGE_TOO_HIGH 4 CPU Usage too high. Limit of [int]*(0.1%) exceeded. Current CPU usage is [int]*(0.1%) |
Log CPU load detected as too high |
|
DIAG CPU_USAGE_TOO_HIGH_RECOVER 4 CPU Usage too high recover. Limit is [int]*(0.1%) |
Current CPU usage is too high |
|
DIAG CPU_LOAD 4 [str] minute average load limit exceeded, value is [str]% limit is [str]% (top processes: [str]) |
CPU average load limit exceeded |
|
DIAG RAM_USAGE 6 [str], pid [uint], has exceeded ram usage limit [uint].[uint]%, now using [uint].[uint]% |
Log processor RAM usage has exceeded RAM limit |
|
DIAG MEM_USAGE_TOO_HIGH 6 Memory Usage too high. Current Usage is [int]*(0.1%). Memory Usage Threshold is [int]*(0.1%) |
Memory usage too high |
|
DIAG MEM_USAGE_TOO_HIGH_RECOVER 6 Memory Usage too high recover. Current Usage is [int]*(0.1%). Memory Usage Threshold is [int]*(0.1%) |
Memory usage detected as too high |
|
DIAG BUF_USAGE 6 [uint] byte buffer usage greater than expected, [uint] used, warning level [uint] |
Log buffer usage greater than anticipated |
|
DIAG HEAD_CACHE_USAGE 6 socket buffer head cache usage is greater than expected, usage [uint], warning level [uint] |
Log head cache usage greater than anticipated |
|
DIAG IP_DEST_USAGE 6 IP destination cache usage is greater than expected, usage [uint], warning level [uint] |
Log destination cache usage greater than anticipated |
|
DIAG FREE_RAM 6 Free RAM, [str]% is less than limit [str]%. Top Memory process: [str]/[uint] using [uint].[uint]% , [str]/[uint] using [uint].[uint]% , [str]/[uint] using [uint].[uint]% |
Log RAM space less than limit |
|
DIAG FREE_FLASH_DISK 4 Free [str] file system space, [str]% is less than limit [str]% |
Log free disk space less than limit |
|
DIAG DISK_USAGE 4 Disk usage too high |
Log disk usage too high |
|
"DIAG NEW_LED_STATE 6 LED state message [str] from module [str] |
Log LED message from module |
|
DIAG FREE_FLASH_INODES 4 [uint] Free INodes on [str] file system is less than limit [uint] |
Log INodes less than system limit |
|
DIAG FREE_NVRAM_DISK 4 Free [str] file system space, [str]% is less than limit [str]% |
Log file system space less than limit |
|
DIAG FREE_NVRAM_INODES 4 [uint] Free INodes on [str] file system is less than limit [uint] |
Log free INodes on file system less than limit |
|
DIAG FREE_RAM_DISK 4 Free [str] file system space, [str]% is less than limit [str]% |
Log free file system space less than limit |
|
DIAG FREE_RAM_INODES 4 [uint] Free INodes on [str] file system is less than limit [uint] |
LOG_FREE_VARFS_INODES |
|
DIAG FD_COUNT 4 FD Usage [uint] is over limit [uint] |
HUMM |
|
DIAG DISK_USAGE 4 Disk usage too high |
Log disk utilization usage too high |
|
DIAG NEW_LED_STATE 6 LED state message [str] from module [str] |
Log LED state message from module |
|
DIAG LED_IDENTIFY 6 LED identify sequence [str] |
Log identification sequence |
|
"DHCPSVR RELAY_NO_IFACE 4 Dhcp relay cannot be allowed on interface [str] as it does not exist |
No interface for DHCP relay |
|
DHCPSVR RELAY_IFACE_NO_IP 4 Dhcp relay cannot be allowed on interface [str] as it does not have an IP address |
No IP address on DHCP relay interface |
|
DHCPSVR RELAY_START 6 DHCP relay agent started on [str] |
DHCP relay agent started |
|
DHCPSVR RELAY_STOP 6 DHCP relay agent stopped |
DHCP relay agent stopped |
|
DHCPSVR DHCPSVR_START 6 DHCP server is started |
DHCP server started |
|
DIAG FAN_UNDERSPEED 4 Fan [str] under speed: [uint] RPM is under limit [uint] RPM |
Fan speed under set RPM limit |
|
DIAG ELAPSED_TIME 7 Elapsed time since last diag run appears to be zero |
Log elapsed time since last diagnostic run |
|
DIAG AUTOGEN_TECH_SPRT 6 Auto generated tech-support dump file [str] [str] |
Log generation of tech support dump file |
|
DIAG POE_INIT_FAIL 3 Could not initialize the PoE manager |
Log PoE manager intialization failure |
|
DIAG POE_POWER_LEVEL 4 POE power consumption is [uint]W which exceeds [uint]% of [uint]W power budget |
Log power consumption exceeds power budget limit |
|
DIAG POE_READ_FAIL 3 Could not read from the PoE |
Log PoE read failure |
|
DIAG POE_STATE_CHANGE 4 port [uint] POE state changed to [str] |
Log PoE state change |
|
DIAG RAID_DEGRADED 4 RAID array is degraded |
Log RAID array degraded |
|
DIAG RAID_ERROR 4 RAID array management error [uint] |
Log RAID array management error |
|
DIAG PWRSPLY_FAIL 4 Power supply failure, no longer redundant |
Log power supply failure |
|
DIAG HDD_FAILING 4 HDD is failing |
Log HDD failure |
|
DIAG UNDER_VOLTAGE 4 Voltage [str]V under low limit [str]V |
Log voltage sensor under low limit |
|
DIAG OVER_VOLTAGE 4 Voltage [str]V over high limit [str]V |
Log voltage sensor over high limit |
|
DIAG LOW_TEMP 6 Temp sensor [str] [str]C under low limit [str]C |
Log temperature sensor under low limit |
|
DIAG HIGH_TEMP 4 Temp sensor [str] [str]C over high limit [str]C |
Log temperature sensor over high limit |
|
DIAG OVER_TEMP 0 Temp sensor [str] [str]C over maximum limit [str]C Shutdown switch |
Log temperature sensor over max limit |
|
DIAG WD_STATE_CHANGE 6 Watchdog is now [str] |
Log watchdog state |
|
DOT1X DOT1X_SUCCESS 6 Client [qstr] 802.1x/EAP authentication success on interface [qstr]//802.1x authentication successful |
802.1X authentication successful |
|
DOT1X DOT1X_FAILED 5 Client [qstr] failed 802.1x/EAP authentication on interface [qstr]//802.1x authentication failure |
802.1X authentication failed |
|
DOT11 COUNTRY_CODE 5 Country of operation configured to [str] |
Country of operation configured |
|
DOT11 COUNTRY_CODE_ERROR 1 Error setting country of operation. [str] |
Error setting country of operation |
|
DOT11 CLIENT_ASSOCIATED 6 Client [qstr] associated to wlan [qstr] ssid [qstr] on radio [qstr] |
Client associated event |
|
DOT11 CLIENT_DISASSOCIATED 6 Client [qstr] disassociated from wlan [qstr] radio [qstr]: [str] (reason code:[uint]) |
Client disassociated |
|
DOT11 CLIENT_DENIED_ASSOC 5 Client [qstr] denied association on radio [qstr] [str]: [str] |
Client denied association |
|
DOT11 CLIENT_ASSOC_IGNORED 6 Client [qstr] ignored association on radio [qstr] [str]: [str] |
Client ignored association |
|
DOT11 WPA_WPA2_SUCCESS 6 Client [qstr] completed [str] handshake on wlan [qstr] radio [qstr] |
Client completed WPA/WPA2 handshake |
|
DOT11 WPA_WPA2_FAILED 5 Client [qstr] failed [str] handshake on wlan [qstr] radio [qstr] |
Client failed WPA/WPA2 handshake |
|
DOT11 WPA_WPA2_KEY_ROTN 6 Rotating wpa/wpa2 group keys on wlan [qstr] / |
Rotating WPA/WPA2 group keys on WLAN |
|
DOT11 TKIP_MIC_FAIL_REPORT 5 TKIP message integrity check failure reported by [mac] on wlan [qstr] |
TKIP MIC failure report |
|
DOT11 TKIP_MIC_FAILURE 5 TKIP message integrity check failed in packet from [mac] on wlan [qstr] |
TKIP MIC check failed |
|
DOT11 TKIP_CNTRMEAS_START 4 Initiating TKIP countermeasures on wlan [qstr] ssid [qstr] |
TKIP countermeasures initiated |
|
DOT11 TKIP_CNTRMEAS_END 4 TKIP countermeasures ended on wlan [qstr] ssid [qstr] // |
TKIP countermeasures ended |
|
DOT11 EAP_SUCCESS 6 Client [qstr] 802.1x/EAP (type:[str]) authentication success on wlan [qstr] radio [qstr] username [str] |
EAP authentication success |
|
DOT11 EAP_FAILED 5 Client [qstr] failed 802.1x/EAP authentication on wlan [qstr] radio [qstr] |
EAP authentication failure |
|
DOT11 EAP_CLIENT_TIMEOUT 5 Client [qstr] timeout attempting 802.1x/EAP authentication on wlan [qstr] radio [qstr] |
EAP authentication timed out |
|
DOT11 EAP_SERVER_TIMEOUT 5 Radius server [str] timeout authenticating client [qstr] on wlan [qstr] radio [qstr] |
RADIUS server timed out |
|
DOT11 EAP_CACHED_KEYS 6 Key Cache used for client [qstr] on wlan [qstr] radio [qstr]. Skipping 802.1x |
Key cache used for authentication |
|
DOT11 EAP_OPP_CACHED_KEYS 6 Opportunistic Key Cache used for client [qstr] on wlan [qstr] radio [qstr]. Skipping 802.1x. |
Opportunistic key caching used for authentication |
|
DOT11 EAP_PREAUTH_SUCCESS 6 Client [qstr] 802.1x/EAP (type:[str]) pre-authentication success on wlan [qstr] bss [mac] |
EAP pre authentication success |
|
DOT11 EAP_PREAUTH_FAILED 5 Client [qstr] failed 802.1x/EAP pre-authentication on wlan [qstr] bss [mac] |
EAP pre-authentication failed |
|
DOT11 EAP_PREAUTH_CLIENT_TIMEOUT 5 Client [qstr] timeout attempting 802.1x/EAP pre-authentication on wlan [qstr] |
EAP pre-authentication client timeout detected |
|
DOT11 EAP_PREAUTH_SERVER_TIMEOUT 5 Radius server [qstr] timeout pre-authenticating client [qstr] on wlan [qstr] |
EAP pre-authentication server timeout detected |
|
DOT11 FT_ROAM_SUCCESS 6 Client [qstr] fast bss transition roam to wlan [qstr] ssid [qstr] on radio [qstr] |
Client fast BSS transition roam to WLAN SSD ID on radio |
|
DOT11 GAL_RX_REQUEST 6 Received request to validate [qstr] on global assoc-list [qstr] from [qstr] on rf-domain [qstr] |
Received request to validate global association request for RF Domain |
|
DOT11 GAL_TX_RESPONSE 6 Sending global assoc-list [qstr] response for [qstr] to [qstr] on rf-domain [qstr], result: [str] |
Sending global association response for RF Domain |
|
DOT11 GAL_VALIDATE_REQ 6 Sending global assoc-list validation request to controller for [qstr] |
Sending global association list validation to controller |
|
DOT11 GAL_VALIDATE_FAILED 6 Received global assoc-list validation failure for [qstr] |
Received global association list validation failures |
|
DOT11 GAL_VALIDATE_SUCCESS 6 Received global assoc-list validation success for [qstr] |
Received global association list validation successes |
|
FWU FWUDONE 6 Firmware update successful, new version is [str] |
Update successfully completed |
|
FWU FWUABORTED 6 Firmware update aborted |
Update aborted |
|
FWU FWUNONEED 6 Firmware update not required, running and update versions same [str] |
Update not required, running and update version are the same |
|
FWU FWUSYSERR 3 Firmware update unsuccessful, system cmd [str] failed |
Update unsuccessful, system cmd failed |
|
FWU FWUBADCONFIG 3 Firmware update unsuccessful, unable to read configuration file |
Update unsuccessful, unable to read config file |
|
FWU FWUSERVERUNDEF 3 Firmware update unsuccessful, update server undefined |
Update unsuccessful, server undefined |
|
FWU FWUFILEUNDEF 3 Firmware update unsuccessful, update file undefined |
Update unsuccessful, update file undefined |
|
FWU FWUSERVERUNREACHABLE 3 Firmware update unsuccessful, server [str] unreachable |
Update unsuccessful, server unreachable |
|
FWU FWUCOULDNTGETFILE 3 Firmware update unsuccessful, couldn't get file, [str] // |
Update unsuccessful, could not get file |
|
FWU FWUVERMISMATCH 3 Firmware update unsuccessful, version mismatch, expected [str], actual [str] // |
Update unsuccessful, version mismatch |
|
FWU FWUPRODMISMATCH 3 Firmware update unsuccessful, product mismatch, expected [str], actual [str] |
Update unsuccessful, product mismatch |
|
FWU FWUCORRUPTEDFILE 3 Firmware update unsuccessful, corrupted firmware file |
Update unsuccessful, corrupted file |
|
FWU FWUSIGNMISMATCH 3 Firmware update unsuccessful, signature mismatch, [str] |
Update unsuccessful, signature mismatch |
|
FWU FWUUNSUPPORTEDHW 3 Firmware update unsuccessful, unsupported hardware |
Update unsuccessful, unsupported hardware version |
|
FWU FWUUNSUPPORTEDMODELNUM 3 Firmware update unsuccessful, unsupported FIPS model number |
Update unsuccessful, unsupported FIPS model number |
|
ISDN_EMERG 0 Emergency: [str] |
ISDN emergency |
|
ISDN_ALERT 1 Alert: [str] |
ISDN alert |
|
ISDN_CRIT 2 Critical: [str] |
ISDN critical |
|
ISDN_ERR 3 Error: [str] |
ISDN error |
|
ISDN_WARNING 4 Warning: [str] |
ISDN warning |
|
ISDN_NOTICE 5 Notice: [str] |
ISDN notice |
|
ISDN_INFO 6 Info: [str] |
ISDN information |
|
ISDN_DEBUG 7 Debug: [str] |
ISDN debug |
|
L2TPV3 L2TPV3_TUNNEL_UP 5 L2TPV3 tunnel [str] is UP |
L2TPV3 tunnel is up |
|
L2TPV3 L2TPV3_TUNNEL_DOWN 5 L2TPV3 tunnel [str] is DOWN |
L2TPV3 tunnel is down |
|
LICMGR LIC_INSTALLED 6 [str] license installed |
License installation |
|
LICMGR LIC_INSTALL_DEFAULT 6 [str] default license installed, count: [int] |
Default license installation |
|
LICMGR LIC_INSTALL_COUNT 6 [str] license installed, count: [int] |
License count |
|
LICMGR LIC_REMOVED 6 [str] license removed |
License removed |
|
LICMGR LIC_INVALID 3 [str] license invalid Error: [str] |
License installation failed |
|
MESH MESH_LINK_UP 5 Mesh link up between radio [qstr] and radio [qstr] |
Mesh link up |
|
MESH MESH_LINK_DOWN 5 Mesh link down between radio [qstr] and radio [qstr] |
Mesh link down |
|
MGMT LOG_KEY_DELETED 4 Rsakey [str] associated with ssh is deleted so ssh is restarted with default rsa key |
RSA key associated with SSH is deleted |
|
MGMT LOG_KEY_RESTORED 6Rsakey [str] associated with ssh is added so ssh is restarted with new key |
RSA key associated with SSH is added |
|
MGMT LOG_TRUSTPOINT_DELETED 4 Trustpoint [str] associated with https is deleted or expired so https is restarted with default trustpoint |
Trustpoint associated with HTTPS is deleted |
|
MGMT LOG_HTTP_START 5 [str] started in external mode |
Web server started in external mode |
|
MGMT LOG_HTTP_LOCAL_START 5 thttpd started in localhost mode |
Web server started in local mode |
|
MGMT LOG_HTTPS_START 5 stunnel started |
Secure Web server started |
|
MGMT LOG_HTTPS_WAIT 5 waiting for thttpd to start |
Waiting for Web server to start |
|
MGMT LOG_HTTP_INIT 5 [str] status started is [uint] and external mode is [uint] |
Web server started |
|
MESH MESHPOINT_LOOP_PREVENT_ON 4 Meshpoint [qstr] loop prevention on (port [str]), wired traffic is blocked |
Wired traffic is blocked |
|
MESH MESHPOINT_LOOP_PREVENT_OFF 4 Meshpoint loop prevention off (port [str]), all wired traffic is allowed |
Wired traffic is allowed |
|
MESH MESHPOINT_ROOT_CHANGE 6 Meshpoint [qstr] root changed from [mac] to [mac] via next hop [mac] |
Meshpoint root changed |
|
MESH MESHPOINT_PATH_CHANGE 6 Meshpoint [qstr] next hop changed from [mac] to [mac] for [mac] |
Meshpoint next hop changed |
|
NSM IFUP 4 Interface [str] is up |
Interface up |
|
NSM IFDOWN 4 Interface [str] is down |
Interface down |
|
NSM DHCPIP 6 Interface [str] acquired IP address [ip]/[uint] via DHC |
Interface assigned DHCP IP address |
|
NSM DHCPDEFRT 6 Default route with gateway [ip] learnt via DHC |
Default route learnt via DHCP |
|
NSM DHCPIPCHG 5 Interface [str] changed DHCP IP - old IP: [ip]/[uint], new IP: [ip]/[uint] |
DHCP Interface IP changed |
|
NSM DHCPNODEFRT 5 Interface [str] lost its DHCP default route |
Interface no default route |
|
NSM IFIPCFG 3 Interface [str] IP address [str] Interface [str] |
Interface IP address |
|
NSM DHCPC_ERR 3 Both, DHCP client and server are configured for interface [str]. DHCP Client has been enabled on the interface and dhcp server is shut down |
DHCP server-client config conflict |
|
NSM DHCPIPNOADD 5 Interface [str] lost its DHCP IP address to interface [str]'s overlapping static configured IP address |
DHCP IP overlaps static IP address |
|
NSM DHCPLSEXP 5 Interface [str] lost its DHCP IP address [ip] due to lease expiration |
Interace DHCP lease expired |
|
NSM DHCPNAK 5 Interface [str] lost its DHCP IP address [ip], DHCP NAK response from server |
DHCP Server returned DHCP NAK response |
|
NSM NSM_NTP 6 Look up host [str] [str]// |
Translate host name |
|
NSM IF_FAILOVER 5 Interface [str] failover to Interface [str] |
Interface failover |
|
NSM IF_FAILBACK 5 Interface [str] failback to Interface [str] |
Interface failback |
|
PM PROCSTART 6 Starting process [str] |
Process started |
|
PM PROCRSTRT 3 Process str]"is not responding. Restarting process |
Process restarted |
|
PM PROCMAXRSTRT 1 Process [str] reached its maximum number of allowed restarts |
Process reached max number of restarts |
|
PM PROCSYSRSTRT 0 Process [str] reached its maximum number of allowed restarts. Rebooting the system. |
Process reached max restarts. Rebooting system. |
|
PM PROCSTOP 5 Process [str] has been stopped |
Process has been stopped |
|
PM PROCID 5 Process [str] changed its PID from [int] to [int] |
Process changed PID |
|
PM STARTUPCOMPLETE 5 System startup complete |
System startup completed |
|
PM PROCNORESP 4 Process [str] is not responding ([uint]/[uint]) |
Process is not responding |
|
RADCONF RADIUSDSTART 6 Radius Server Started |
RADIUS server started |
|
RADCONF RADIUSDSTOP 6 Radius Server Stopped |
RADIUS server stopped |
|
RADCONF COULD_NOT_STOP_RADIUSD 3 radiusd could not be stopped |
RADIUS server failed to stop |
|
RADIO RADIO_STATE_CHANGE 5 Radio [qstr] changing state from [qstr] to [qstr] |
Radio state changed |
|
RADIO RADAR_SCAN_STARTED 6 Radar scan on primary channel [uint] freq [uint] MHz for a duration [uint] secs on radio [qstr] |
Radar scan started |
|
RADIO RADAR_SCAN_COMPLETED 6 Radar scan done on primary channel [uint] freq [uint] MHz on radio [qstr] |
Radar scan completed |
|
RADIO RADAR_DETECTED 4 Radar found on channel [uint] freq [uint] MHz |
Radar detected |
|
RADIO RADAR_DET_INFO 4 Radar info: Radio: [qstr]. New channel: [uint] freq [uint] MHz. Scan time: [uint] secs |
Radar info |
|
RADIO RESUME_HOME_CHANNEL 6 Operation on home channel [uint] freq [uint] MHz resumes on radio [qstr] after earlier radar detect |
Radio resuming on home channel |
|
RADIO ACS_SCAN_STARTED 6 ACS scan started on radio [qstr] |
ACS scan started |
|
RADIO ACS_SCAN_COMPLETE 6 ACS scan done, channel [uint] selected on radio [qstr] |
ACS scan complete |
|
RADIO_ANTENNA_ERROR 3 antenna type [str] in is not supported on radio [uint] of device [str] |
Invalid (unsupported) antenna detected on this radio |
|
RADIO CHANNEL_COUNTRY_MISMATCH 3 Channel [str] not valid in country of operation [str] for [str] [str] |
Channel and country of operation mismatch |
|
SYSTEM HTTP_ERR 3 [str] did not start |
Web server did not start |
|
SYSTEM LOGIN_FAIL_BAD_ROLE 3 Log-in failed - [qstr] is an undefined user role - user [qstr] from [qstr] |
Failed login attempt - no such user role |
|
SYSTEM LOGOUT 6 Logged out user [qstr] with privilege [qstr] from [qstr] |
Logout event |
|
SYSTEM WARM_START 6 System Warm Start Reason : [str] Timestamp: [str] |
System warm start |
|
SYSTEM WARM_START_RECOVER 6 Warm Start Recover. Reason: [str] Timestamp: [str] |
System wam start recovery |
|
SYSTEM COLD_START 6 System Cold start. System came up at [str] |
System cold start |
|
SYSTEM SERVER_UNREACHABLE 5 Server not reachable, trying authentication using local database . |
Authentication using the local database |
|
SYSTEM PERIODIC_HEART_BEAT 3 Periodic Heart Beat. Interval:[int]. Ip address [str]. |
Periodic heartbeat detected |
|
SYSTEM CONFIG_COMMIT 6 Configuration commit by user [qstr] ([str]) from [qstr] |
Configuration commit |
|
SYSTEM CONFIG_REVISION 6 Configuration revision updated to [str] from [str] |
Configuration updated |
|
SYSTEM SYSTEM_AUTOUP_ENABLE 6 Autoupgrade enabled for [str] |
Auto upgrade module is enabled |
|
SYSTEM SYSTEM_AUTOUP_DISABLE 6 Autoupgrade disabled for [str] |
Auto upgrade module is disabled |
|
SYSTEM MAAT_LIGHT 5 MAAT Light module [str] |
Notice on action on RIM radio(s) from Maat Light module |
|
SYSTEM DEVUP_RFD_FAIL 4 Upgrade failed on mac [str] in RF domain [str] |
Upgrade for device failed on rf-domain manager |
|
SMTPNOT SMTPAUTH 5 Authentication failure for user: [str] on server [str].// |
User authentication failure |
|
SMTPNOT NET 5 Network error contacting server: [str]. |
Cannot contact server |
|
SMTPNOT SMTPINFO 6 [str]. |
SMTP information notice |
|
SMTPNOT CFG 5 Error reading configuration file. |
Cannot read configuration |
|
SMTPNOT CFGINC 5 Incomplete Configuration. |
Incomplete configuration |
|
SMTPNOT SMTPERR 5 [str]. |
SMTP 5XX errors |
|
SMTPNOT PROTO 5 Protocol Error: [str]. |
SMTP protocol errors |
|
SYSTEM PROC_STOP 6 Stopping process [qstr] |
Stopping process |
|
SYSTEM CLOCK_RESET 6 System clock reset, Time: [str] |
System clock reset |
|
SYSTEM LOGIN 5 Successfully logged in user [qstr] with privilege [qstr] from [qstr] |
Successful login |
|
SYSTEM LOGIN_FAIL 3 Log-in failed for user [qstr] from [qstr] |
Failed login attempt - user authentication failed |
|
SYSTEM LOGIN_FAIL_ACCESS 3 Log-in failed - user [qstr] is not allowed access from [qstr] |
Failed login attempt - access violation |
|
VRRP VRRP_STATE_CHANGE 5 [str]: VRRP Group [uint] transitioned to [str] state |
VRRP state transition |
|
VRRP VRRP_VIP_SUBNET_MISMATCH 2 VRRP Group [uint] VIP [ip] does not overlap with any of the interface addresses |
VRRP IP not overlapping with interface addresses |
|
VRRP VRRP_MONITOR_CHANGE 5 [str]: VRRP Group [uint] monitored [str] state change to [str]; priority change from [uint] to [uint] |
VRRP monitor link state change |
|
WIPS UNSANCTIONED_AP_ACTIVE 6 Unsanctioned AP [mac] vendor [str] on channel [int] with rssi [int] active from [str] |
Unsanctioned AP active |
|
WIPS UNSANCTIONED_AP_INACTIVE 6 Unsanctioned AP [mac] vendor [str] inactive from [str] |
Unsanctioned AP inactive |
|
WIPS UNSANCTIONED_AP_STATUS_CHANGE 6 Unsanctioned AP [mac] vendor [str] status has been administratively changed |
Unsanctioned AP changed state |
|
WIPS ROGUE_AP_ACTIVE 4 Rogue AP [mac] vendor [str] on channel [int] with vlan [int] and rssi [int] active from [str] // |
Rogue AP active |
|
WIPS ROGUE_AP_INACTIVE 4 Rogue AP [mac] vendor [str] inactive from [str] |
Rogue AP inactive |
|
WIPS AIR_TERMINATION_INITIATED 4 Air termination of [mac] vendor [str] on channel [int] initiated |
Air termination initiated |
|
WIPS AIR_TERMINATION_ENDED 4 Air termination of [mac] vendor [str] ended |
Air termination ended |