show ipv6 interface
Show IPv6 information for all or specific interfaces.
Syntax
-
show ipv6 interface
gigabitethernet
[{slot/port[/sub-port][-slot/port[/sub-port]][,...]}]
-
show ipv6 interface
icmpstatistics
-
show ipv6 interface
icmpstatistics gigabitEthernet
[{slot/port[/sub-port][-slot/port[/sub-port]][,...]}]
-
show ipv6 interface
icmpstatistics loopback <1-256>
-
show ipv6 interface
icmpstatistics tunnel <1-2000>
-
show ipv6 interface
icmpstatistics vlan <1-4059>
-
show ipv6 interface
icmpstatistics vrf WORD<1-16>
-
show ipv6 interface
icmpstatistics vrfids WORD<0-512>
-
show ipv6 interface
loopback <1-256>
-
show ipv6 interface
statistics
-
show ipv6 interface
statistics gigabitEthernet
[{slot/port[/sub-port][-slot/port[/sub-port]][,...]}]
-
show ipv6 interface
statistics loopback <1-256>
-
show ipv6 interface
statistics tunnel <1-2000>
-
show ipv6 interface
statistics vlan <1-4059>
-
show ipv6 interface
statistics vrf WORD<1-16>
-
show ipv6 interface
statistics vrfids WORD<0-512>
-
show ipv6 interface tunnel
<1-2000>
-
show ipv6 interface tunnel
vrf WORD<1-16>
-
show ipv6 interface tunnel
vrfids WORD<0-512>
-
show ipv6 interface vlan
[<1-4059>]
-
show ipv6 interface vrf
WORD<1-16>
-
show ipv6 interface vrfids
WORD<0-512>
Command Parameters
- gigabitEthernet {slot/port[/sub-port][-slot/port[/sub-port]][,...]}
- Displays IPv6 interface
information for gigabitEthernet.
{slot/port[/sub-port][-slot/port[/subport]][,...]} identifies the slot and port in
one of the following formats: a single slot and port (slot/port), a range of slots
and ports (slot/port-slot/port), or a series of slots and ports
(slot/port,slot/port,slot/port). If your platform supports channelization and the
port is channelized, you must also specify the sub-port in the format
slot/port/sub-port.
- icmpstatistics [gigabitEthernet | mgmtEthernet | tunnel | vlan]
- Shows IPv6 ICMP statistics for the
interface as follows: gigabitEthernetdisplays interface gigabitEthernet
configurations, mgmtEthernet-displays interface mgmtEthernet configurations,
tunnel-displays interface tunnel configurations, vlan -displays vlan interface
configurations.
- loopback <1-256>
- Displays the interface loopback
configurations.
- loopback <1-256>
- Identifies a loopback
interface.
- statistics [gigabitEthernet | mgmtEthernet | tunnel | vlan]
- Shows IPv6 interface statistics as
follows: gigabitEthernet- displays interface gigabitEthernet configurations,
mgmtEthernet-displays interface mgmtEthernet configurations, tunnel- displays
interface tunnel configurations, vlan -displays vlan interface
configurations.
- tunnel <1-2000>
- Displays IPv6 interface
information for a tunnel. The tunnel ID is expressed as a value from 1 to
2000.
- vlan <1-4059>
-
Specifies the
VLAN ID in the range of 1 to 4059. By default, VLAN IDs 1 to
4059 are configurable and the system reserves VLAN IDs 4060 to
4094 for internal use. On switches that support the vrf-scaling and spbm-config-mode boot configuration flags, if
you enable these flags, the system also reserves VLAN IDs 3500
to 3998. VLAN ID 1 is the default VLAN and you cannot create or
delete VLAN ID 1.
- vrf WORD<1-16>
- Specifies a VRF name. The VRF
parameter is optional.
- vrfids WORD<0-512>
- Specifies a VRF by ID. The VRF
parameter is optional.
