interface-config-radio-instance
Negates a command or resets settings to their default. When used in the profile/device > radio interface configuration mode, the no command disables or resets radio interface settings.
no <PARAMETERS>
no <PARAMETERS>
| no <PARAMETERS> | Removes or reverts this radio interface‘s settings based on the parameters passed |
The no command negates any command associated with it. Wherever required, use the same parameters associated with the command getting negated.
nx9500-6C8809(config-profile-ap71xxTest-if-radio1)#no ?
adaptivity Adaptivity
aeroscout Use Default Aeroscout Multicast MAC Address
aggregation Configure 802.11n aggregation related parameters
airtime-fairness Disable fair access to medium for clients,
provide access in a round-robin mode
antenna-diversity Use single antenna for non-11n transmit rates
antenna-downtilt Reset ADEPT antenna mode
antenna-elevation Reset the antenna elevation of this radio to
default
antenna-gain Reset the antenna gain of this radio to default
antenna-mode Reset the antenna mode (number of transmit and
receive antennas) on the radio to its default
assoc-response Configure transmission parameters for
Association Response frames
association-list Configure the association list for the radio
beacon Configure beacon parameters
bridge Bridge rf-mode related configuration
channel Reset the channel of operation of this radio to
default
data-rates Reset radio data rate configuration to default
description Reset the description of the radio to its
default
dfs-rehome Stay on dfs elected channel after evacuation
period expires
dynamic-chain-selection Use the configured transmit antenna mode for all
clients
ekahau Use Default Ekahau Multicast MAC Address
extended-range Reset extended range to default
fallback-channel Clear the DFS fallback channel for this radio
guard-interval Configure default value of 802.11n guard
interval (long: 800nSec)
ldpc Configure support for Low Density Parity Check
Code
lock-rf-mode Allow smart-rf to change rf-mode setting for
this radio
max-clients Maximum number of wireless clients allowed to
associate
mesh Disable mesh mode operation of the radio
meshpoint Disable a meshpoint from this radio
mu-mimo Disable multi user MIMO on this radio (selected
platforms only)
non-unicast Configure handling of non-unicast frames
off-channel-scan Disable off-channel scanning on the radio
placement Reset the placement of the radio to its default
power Reset the transmit power of this radio to
default
preamble-short Disable the use of short-preamble on this radio
probe-response Configure transmission parameters for Probe
Response frames
radio-resource-measurement Configure support for 802.11k Radio Resource
Measurement
radio-share-mode Configure the radio-share mode of operation for
this radio
rate-selection Monotonic rate selection
rf-mode Reset the RF mode of operation for this radio to
default (2.4GHz on radio1, 5GHz on radio2,
sensor on radio3)
rifs Configure Reduced Interframe Spacing (RIFS)
parameters
rts-threshold Reset the RTS threshold to its default (65536)
rx-sensitivity-reduction Configure radio receive sensitivity reduction
threshold
shutdown Re-enable the selected interface
smart-rf Reset smart-rf related configuration to default
sniffer-redirect Disable capture and redirection of packets
stbc Configure Space-Time Block Coding (STBC)
parameters
transmit-beamforming Disable Transmit Beamforming
use Set setting to use
wips Wireless intrusion prevention related
configuration
wireless-client Configure wireless client related parameters
wlan Disable a wlan from this radio
service Service Commands
nx9500-6C8809(config-profile-ap71xxTest-if-radio1)#
The following example shows radio interface settings before the ‘no‘ commands are executed:
nx9500-6C8809(config-profile-71xxTestProfile-if-radio1)#show context interface radio1 description "Primary radio to use" channel 1 data-rates b-only mesh client beacon period 50 beacon dtim-period bss 1 5 beacon dtim-period bss 2 2 beacon dtim-period bss 3 5 beacon dtim-period bss 4 5 beacon dtim-period bss 5 5 beacon dtim-period bss 6 5 beacon dtim-period bss 7 5 beacon dtim-period bss 8 5 beacon dtim-period bss 9 5 beacon dtim-period bss 10 5 beacon dtim-period bss 11 5 beacon dtim-period bss 12 5 beacon dtim-period bss 13 5 beacon dtim-period bss 14 5 beacon dtim-period bss 15 5 beacon dtim-period bss 16 5 antenna-gain 12.0 guard-interval long aggregation ampdu tx-only aeroscout forward ekahau forward ip 172.16.10.1 port 3 antenna-mode 2x2 antenna-diversity max-clients 100 airtime-fairness prefer-ht weight 6 lock-rf-mode extended-range 15 antenna-downtilt nx9500-6C8809(config-profile-71xxTestProfile-if-radio1)# nx9500-6C8809(config-profile-71xxTestProfile-if-radio1)#no channel nx9500-6C8809(config-profile-71xxTestProfile-if-radio1)#no antenna-gain nx9500-6C8809(config-profile-71xxTestProfile-if-radio1)#no description nx9500-6C8809(config-profile-71xxTestProfile-if-radio1)#no antenna-mode nx9500-6C8809(config-profile-71xxTestProfile-if-radio1)#no beacon dtim-period nx9500-6C8809(config-profile-71xxTestProfile-if-radio1)#no beacon period
The following example shows radio interface settings after the ‘no‘ commands are executed:
nx9500-6C8809(config-profile-71xxTestProfile-if-radio1)#show context interface radio1 data-rates b-only mesh client guard-interval long aggregation ampdu tx-only aeroscout forward ekahau forward ip 172.16.10.1 port 3 antenna-diversity max-clients 100 airtime-fairness prefer-ht weight 6 lock-rf-mode extended-range 15 antenna-downtilt nx9500-6C8809(config-profile-71xxTestProfile-if-radio1)#