Displays the contents of the IP routing table or the route origin priority.
| priority | Displays the priority values for each route origin type. |
| vlan_name | Specifies a VLAN (Virtual LAN) name. |
| permanent | Specifies permanent routing. |
| ip_address | Specifies an IP address. |
| netmask | Specifies a subnet mask. |
| summary | Displays summary information. |
| multicast | Displays information for IPv4 multicast routes only. |
| unicast | Displays information for IPv4 unicast routes only. |
| vrname | Specifies a VR or VRF. |
N/A.
A c flag in the Flags column indicates a compressed route resulting from enabling compression using the enable iproute compression command. The total number of compressed routes is also shown.
All routes that are provided to the FIB display the f flag.
If you do not specify a VR or VRF, the command applies to the current VR context.
The following example displays detailed information about all IP routing:
Print
this page
Email this topic
Feedback
View PDF
Download EPUBSwitch.3 # show iproute
Ori Destination Gateway Mtr Flags VLAN Duration
d 2.2.0.0/16 2.2.2.3 1 -------um--- v2 2d:10h:17m:41s
#d 3.2.2.0/24 3.2.2.23 1 U------um--f jim_igmp 1d:19h:49m:49s
d 3.3.3.0/24 3.3.3.1 1 -------um--- v3 2d:10h:17m:49s
d 4.4.4.0/24 4.4.4.2 1 -------um--- v4 2d:10h:17m:5s
*hm 192.168.23.1/32 192.168.23.1 1 UGHD---u---f- vlan23 0d:0h:16m:5s
Origin(Ori): (b) BlackHole, (be) EBGP, (bg) BGP, (bi) IBGP, (bo) BOOTP
(ct) CBT, (d) Direct, (df) DownIF, (dv) DVMRP, (e1) ISISL1Ext
(e2) ISISL2Ext, (h) Hardcoded, (i) ICMP, (i1) ISISL1 (i2) ISISL2
(is) ISIS, (mb) MBGP, (mbe) MBGPExt, (mbi) MBGPInter, (mp) MPLS Lsp
(mo) MOSPF (o) OSPF, (o1) OSPFExt1, (o2) OSPFExt2
(oa) OSPFIntra, (oe) OSPFAsExt, (or) OSPFInter, (pd) PIM-DM, (ps) PIM-SM
(r) RIP, (ra) RtAdvrt, (s) Static, (sv) SLB_VIP, (hm) Host-mobility, (un) UnKnown
(*) Preferred unicast route (@) Preferred multicast route
(#) Preferred unicast and multicast route
Flags: (B) BlackHole, (b) BFD protection requested, (c) Compressed, (D) Dynamic
(f) Provided to FIB, (G) Gateway, (H) Host Route,
(I) ICMP ping protection requested, (l) Calculated LDP LSP,(L) Matching LDP LSP
(l) Calculated LDP LSP, (3) L3VPN Route, (m) Multicast, (P) LPM-routing
(p) BFD protection active, (R) Modified, (S) Static, (s) Static LSP
(T) Matching RSVP-TE LSP, (t) Calculated RSVP-TE LSP, {u) Unicast, (U) Up
Mask distribution:
1 routes at length 16 3 routes at length 24
Route Origin distribution:
4 routes from Direct
Total number of routes = 4
Total number of compressed routes = 0
This command was first available in ExtremeXOS 10.1.
The ipv4 keyword was added in ExtremeXOS 11.2.
The c flag was added in ExtremeXOS 12.0.
The f flag was added in ExtremeXOS 12.2.2.
The I flag showing ICMP (Internet Control Message Protocol) ping protection was added in ExtremeXOS 22.1.
This command is available on the Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X440-G2, X620, X690, X870 series switches.