Create an AP510 Profile

Follow the steps below to configure an AP510 profile:

In the NX9500's global config mode:

nx9500-6C8809(config)#profile ap510 AP510_UseCase1
nx9500-6C8809(config-profile-AP510_UseCase1)#

Assign the profile to the VLAN defined in Creating a Wireless Controller Profile. In this section, the VLAN was defined as VLAN 2. When applied to the AP510 access point, this profile will configure the AP to be a member of VLAN 2.
```
nx9500-6C8809(config-profile-AP510_UseCase1)#interface vlan 2
nx9500-6C8809(config-profile-AP510_UseCase1-if-vlan2)#
```
Configure this VLAN to use DHCP. Enabling DHCP on the VLAN ensures that devices associating using this access point are automatically assigned a unique IP address. Once completed, exit this context.
```
nx9500-6C8809(config-profile-AP510_UseCase1-if-vlan2)#ip address dhcp
nx9500-6C8809(config-profile-AP510_UseCase1-if-vlan2)#exit
```
Map the VLAN to a physical interface on the profile. In this example, VLAN 2 is mapped the GE1 interface. When applied to the AP510 access point, this profile will map VLAN 2 to the AP's GE1 port.
```
nx9500-6C8809(config-profile-AP510_UseCase1)#interface ge 1
nx9500-6C8809(config-profile-AP510_UseCase1-if-ge1)#switchport access vlan 2
nx9500-6C8809(config-profile-AP510_UseCase1-if-ge1)#exit
```

Map the WLAN to a radio on the access point. An AP510 has 2 radios, in this scenario, both radios are mapped to WLAN '1' created earlier.

nx9500-6C8809(config-profile-AP510_UseCase1)#interface radio 1
nx9500-6C8809(config-profile-AP510_UseCase1-if-radio1)#wlan 1
nx9500-6C8809(config-profile-AP510_UseCase1-if-radio1)#exit
nx9500-6C8809(config-profile-AP510_UseCase1)#interface radio 2
nx9500-6C8809(config-profile-AP510_UseCase1-if-radio2)#wlan 1
nx9500-6C8809(config-profile-AP510_UseCase1-if-radio2)#exit
nx9500-6C8809(config-profile-AP510_UseCase1)#

Commit the changes and exit.

nx9500-6C8809(config-profile-AP510_UseCase1)#commit write memory
nx9500-6C8809(config-profile-AP510_UseCase1)#exit
nx9500-6C8809(config)#

Apply this profile to the discovered AP510.
1. Use the discovered AP510's MAC address to access the AP's configuration context, as shown here.
```
nx9500-6C8809(config)#ap510 94-9B-2C-13-3B-38
nx9500-6C8809(config-device-94-9B-2C-13-3B-38)#
```
2. Assign the profile to this AP510.
```
nx9500-6C8809(config-device-94-9B-2C-13-3B-38)#use profile AP510_UseCase1
nx9500-6C8809(config-device-94-9B-2C-13-3B-38)#commit write
```
3. Apply the RF Domain to the AP.
  Apply the previously created RF Domainto enable a country code to be assigned to the discovered access point. A discovered access point only works properly if its country code is the country code of its associated wireless controller.
```
nx9500-6C8809(config-device-94-9B-2C-13-3B-38)#use rf-domain RFDOMAIN_UseCase1
nx9500-6C8809(config-device-94-9B-2C-13-3B-38)#commit write
nx9500-6C8809(config-device-94-9B-2C-13-3B-38)#exit
nx9500-6C8809(config)#
```