data-rates (meshpoint-config)

Configures individual data rates for the 2.4 GHz and 5.0 GHz frequency bands. In Mesh network, a mesh point is a virtual mesh networking instance on a device, similar to a WLAN AP. On each device, up to 4 mesh points can be created and 2 can be created per radio. Each mesh point radio can have carefully administrated radio rates specific to the 2.4 or 5 GHz band. Use this command to configure these radio rates.
Note

Note

Ensure that the basic data rates configured on a meshpoint‘s root and non-root access points is the same.

Configured on WiNG 7.1.X controller and pushed to the following WiNG 5.9.X APs:

  • Access Points — AP7502, AP7522, AP7532, AP7562, AP7602, AP7612, AP7622, AP7632, AP7662, AP8163, AP8543, AP8533

Syntax

data-rates [2.4GHz|5GHz]
data-rates 2.4GHz [b-only|bg|bgn|default|g-only|gn]
data-rates 2.4GHz custom (1|11|12|18|2|24|36|48|5.5|54|6|9|basic-1|basic-11|
basic-12|basic-18|basic-2|basic-24|basic-36|basic-48|basic-5.5|basic-54|basic-6|basic-9|
mcs0-15|mcs0-7|mcs8-15|basic-mcs0-7)
data-rates 5GHz [a-only|an|default]
data-rates 5GHz custom (12|18|24|36|48|54|6|9|basic-1|basic-11|basic-12|basic-18|
basic-2|basic-24|basic-36|basic-48|basic-5.5|basic-54|basic-6|basic-9|mcs0-15|mcs0-7|mcs8-15|
basic-mcs0-7)

Parameters

data-rates 2.4GHz [b-only|bg|bgn|default|g-only|gn]

data-rates 2.4GHz

Configures preset data rates for the 2.4 GHz frequency.

b-only

Configures data rate for the meshpoint using 802.11b only rates.

bg

Configures data rate for the meshpoint using 802.11b and 802.11g rates.

default

Configures data rate for the meshpoint at a pre-configured default rate for this frequency.

g-only

Configures data rate for the meshpoint using 802.11g only rates.

gn

Configures data rate for the meshpoint using 802.11g and 802.11n rates.

data-rates 2.4GHz custom (1|11|12|18|2|24|36|48|5.5|54|6|9|basic-1|basic-11|
basic-12|basic-18|basic-2|basic-24|basic-36|basic-48|basic-5.5|basic-54|basic-6|basic-9|
mcs0-15|mcs0-7|mcs8-15|basic-mcs0-7)

data-rates 2.4GHz

Configures the preset data rates for the 2.4 GHz frequency

Define both minimum Basic and optimal Supported rates as required for the 802.11b rates, 802.11g rates and 802.11n rates supported by the 2.4 GHz band. These are the rates wireless client traffic is supported within this mesh point.

These are the rates wireless client traffic is supported within this mesh point. If supporting 802.11n, select a supported MCS index. Set a MCS (Modulation and Coding Scheme) in respect to the radio's channel width and guard interval. A MCS defines (based on RF channel conditions) an optimal combination of 8 data rates, bonded channels, multiple spatial streams, different guard intervals and modulation types.

Meshpoints can communicate as long as they support the same basic MCS (as well as non-802.11n basic rates). The selected rates apply to associated client traffic within this mesh point only.

custom (1|11|12|18|2|24|36| 48|5.5|54|6|9|basic-1| basic-11|basic-12|basic-18|basic-2|basic-24|basic-36| basic-48|basic-5.5|basic-54|basic-6|basic-9|mcs0-15| mcs0-7|mcs8-15| basic-mcs0-7)

Configures custom rates

  • 1 – Configures the available rate at 1 Mbps

  • 2 – Configures the available rate at 2 Mbps

  • 5.5 – Configures the available rate at 5.5 Mbps

  • 6 – Configures the available rate at 6 Mbps

  • 9 – Configures the available rate at 9 Mbps

  • 11 – Configures the available rate at 11 Mbps

  • 12 – Configures the available rate at 12 Mbps

  • 18 – Configures the available rate at 18 Mbps

  • 24 – Configures the available rate at 24 Mbps

  • 36 – Configures the available rate at 36 Mbps

  • 48 – Configures the available rate at 48 Mbps

  • 54 – Configures the available rate at 54 Mbps

  • basic-1 – Configures the available rate at a basic rate of 1 Mbps

  • basic-2 – Configures the available rate at a basic rate of 2 Mbps

  • basic-5.5 – Configures the available rate at a basic rate of 5.5 Mbps

  • basic-6 – Configures the available rate at a basic rate of 6 Mbps

  • basic-9 – Configures the available rate at a basic rate of 9 Mbps

  • basic-11 – Configures the available rate at a basic rate of 11 Mbps

  • basic-12 – Configures the available rate at a basic rate of 12 Mbps

  • basic-18 – Configures the available rate at a basic rate of 18 Mbps

  • basic-24 – Configures the available rate at a basic rate of 24 Mbps

  • basic-36 – Configures the available rate at a basic rate of 36 Mbps

  • basic-48 – Configures the available rate at a basic rate of 48 Mbps

  • basic-54 – Configures the available rate at a basic rate of 54 Mbps

  • basic-mcs0-7 – Configures the MCS index range of 0 - 7 for basic rate

  • mcs0-7 – Configures the MCS index range of 0-7 as the data rate

  • mcs0-15 – Configures the MCS index range of 0-15 as the data rate

  • msc8-15 – Configures the MCS index range of 8-15 as the data rate

Multiple choices can be made from the above list of rates

data-rates 5GHz [a-only|an|default]

data-rates 5GHz

Configures the preset data rates for the 5.0 GHz frequency

a-only

Configures the data rate for the meshpoint using 802.11a only rates

bn

Configures the data rate for the meshpoint using 802.11a and 802.11n rates

default

Configures the data rate for the meshpoint at a pre-configured default rate for this frequency

g-only

Configures the data rate for the meshpoint using 802.11g only rates

gn

Configures the data rate for the meshpoint using 802.11g and 802.11n rates

data-rates 5GHz custom (12|18|24|36|48|54|6|9|basic-1|basic-11|basic-12|basic-18|
basic-2|basic-24|basic-36|basic-48|basic-5.5|basic-54|basic-6|basic-9|mcs0-15|mcs0-7|mcs8-15|
basic-mcs0-7)

data-rates 5GHz

Configures the preset data rates for the 5.0 GHz frequency

Define both minimum Basic and optimal Supported rates as required for 802.11a and 802.11n rates supported by the 5.0 GHz radio band. These are the rates wireless client traffic is supported within this mesh point.

If supporting 802.11n, select a supported MCS index. Set a MCS in respect to the radio's channel width and guard interval. A MCS defines (based on RF channel conditions) an optimal combination of 8 data rates, bonded channels, multiple spatial streams, different guard intervals and modulation types. Mesh points can communicate as long as they support the same basic MCS (as well as non-802.11n basic rates). The selected rates apply to associated client traffic within this mesh point only.

custom (12|18|24|36|48|54| 6|9|basic-1|basic-11| basic-12|basic-18|basic-2| basic-24|basic-36|basic-48| basic-5.5|basic-54|basic-6|basic-9|mcs0-15|mcs0-7| mcs8-15|basic-mcs0-7)

Configures custom rates

  • 6 – Configures the available rate at 6 Mbps

  • 9 – Configures the available rate at 9 Mbps

  • 12 – Configures the available rate at 12 Mbps

  • 18 – Configures the available rate at 18 Mbps

  • 24 – Configures the available rate at 24 Mbps

  • 36 – Configures the available rate at 36 Mbps

  • 48 – Configures the available rate at 48 Mbps

  • 54 – Configures the available rate at 54 Mbps

  • basic-1 – Configures the available rate at a basic rate of 1 Mbps

  • basic-2 – Configures the available rate at a basic rate of 2 Mbps

  • basic-5.5 – Configures the available rate at a basic rate of 5.5 Mbps

  • basic-6 – Configures the available rate at a basic rate of 6 Mbps

  • basic-9 – Configures the available rate at a basic rate of 9 Mbps

  • basic-11 – Configures the available rate at a basic rate of 11 Mbps

  • basic-12 – Configures the available rate at a basic rate of 12 Mbps

  • basic-18 – Configures the available rate at a basic rate of 18 Mbps

  • basic-24 – Configures the available rate at a basic rate of 24 Mbps

  • basic-36 – Configures the available rate at a basic rate of 36 Mbps

  • basic-48 – Configures the available rate at a basic rate of 48 Mbps

  • basic-54 – Configures the available rate at a basic rate of 54 Mbps

  • basic-mcs0-7 – Configures the MCS index range of 0-7 for basic rate

  • mcs0-7 – Configures the MCS index range of 0-7 as the data rate

  • mcs0-15 – Configures the MCS index range of 0-15 as the data rate

  • msc8-15 – Configures the MCS index range of 8-15 as the data rate

Multiple choices can be made from the above list of rates.

Examples

nx9500-6C8809(config-meshpoint-test)#data-rates 2.4GHz bgn
nx9500-6C8809(config-meshpoint-test)#data-rates 5GHz an
nx9500-6C8809(config-meshpoint-test)#show context
meshpoint test
 meshid test
 beacon-format mesh-point
 control-vlan 25
 allowed-vlans 1,10-16,18-23
 data-rates 2.4GHz bgn
 data-rates 5GHz an
 security-mode none
 no root
nx9500-6C8809(config-meshpoint-test)#

Related Commands

no (meshpoint-config)

Resets data rates for each frequency band for this meshpoint