customize

Customizes the output of the summary CLI commands. Use this command to define the data displayed as a result of various show commands.

Supported in the following platforms:

  • Access Points — AP505i, AP510i/e, AP560i/h
  • Service Platforms — NX5500, NX7500, NX9500, NX9600, VX9000

Syntax

customize [cdp-lldp-info-column-width|hostname-column-width|show-adoption-status|
show-wireless-client|show-wireless-client-stats|show-wireless-client-stats-rf|
show-wireless-meshpoint|show-wireless-meshpoint-accelerated-multicast|
show-wireless-meshpoint-neighbor-stats|show-wireless-meshpoint-neighbor-stats-rf|
show-wireless-mint-client|show-wireless-mint-client-stats|
show-wireless-mint-client-stats-rf|show-wireless-mint-portal|
show-wireless-mint-portal-stats|show-wireless-mint-portal-stats-rf|
show-wireless-radio|show-wireless-radio-stats|show-wireless-radio-stats-rf]
customize [cdp-lldp-info-column-width|hostname-column-width] <1-64>
customize show-adoption-status (adopted-by,ap-name <1-64>,cdp-lldp-info,
config-status,last-adoption,msgs,uptime,version)
customize show-wireless-client (ap-name <1-64>,auth,client-identity <1-32>,bss,
enc,hostname <1-64>,ip,last-active,location <1-64>,mac,radio-alias <3-67>,radio-id,
radio-type,role <1-32>,state,username <1-64>,vendor,vlan,wlan)
customize show-wireless-client-stats (hostname <1-64>,mac,rx-bytes,rx-errors,
rx-packets,rx-throughput,t-index,tx-bytes,tx-dropped,tx-packets,tx-throughput)
customize show-wireless-client-stats-rf (average-retry-number,error-rate,
hostname <1-64>,mac,noise,q-index,rx-rate,signal,snr,tx-rate)
customize show-wireless-meshpoint-accelerated-multicast 
(ap-hostname,group-addr,mesh-name,neighbor-hostname,neighbor-ifid,radio-alias,
radio-id,radio-mac,subscriptions)
customize show-wireless-meshpoint (ap-mac,cfg-as-root,hops,hostname <1-64>,
interface-ids,is-root,mesh-name <1-64>,mpid,next-hop-hostname <1-64>,next-hop-ifid,
next-hop-use-time,path-metric,root-bound-time,root-hostname <1-64>,root-mpid)
customize show-wireless-meshpoint-neighbor-stats (ap-hostname <1-64>,
neighbor-hostname <1-64>,neighbor-ifid,rx-bytes,rx-errors,rx-packets,rx-throughput,
t-index,tx-bytes,tx-dropped,tx-packets,tx-throughput)
customize show-wireless-meshpoint-neighbor-stats-rf (ap-hostname <1-64>,
average-retry-number,error-rate,neighbor-hostname <1-64>,neighbor-ifid,noise,q-index,
rx-rate,signal,snr,t-index,tx-rate)
customize show-wireless-mint-client (client-alias <1-64>,client-bss,
portal-alias <1-64>,portal-bss,up-time)
customize show-wireless-mint-client-stats (client-alias <1-64>,
portal-alias <1-64>,portal-bss,rx-bytes,rx-errors,rx-packets,rx-throughput,t-index,
tx-bytes,tx-dropped,tx-packets,tx-throughput)
customize show-wireless-mint-client-stats-rf (average-retry-number,
client-alias <1-64>,error-rate,noise,portal-alias <1-64>,portal-bss,q-index,rx-rate,
signal,snr,tx-rate)
customize show-wireless-mint-portal (client-alias <1-64>,client-bss,
portal-alias <1-64>,portal-bss,up-time)
customize show-wireless-mint-portal-stats (client-alias <1-64>,client-bss,
portal-alias <1-64>,rx-bytes,rx-errors,rx-packets,rx-throughput,t-index,tx-bytes,
tx-dropped,tx-packets,tx-throughput)
customize show-wireless-mint-portal-stats-rf (average-retry-number,
client-alias <1-64>,client-bss,error-rate,noise,portal-alias <1-64>,q-index,rx-rate,
signal,snr,tx-rate)
customize show-wireless-radio (adopt-to,ap-name <1-64>,channel,location <1-64>,
num-clients,power,radio-alias <3-67>,radio-id,radio-mac,rf-mode,state)
customize show-wireless-radio-stats (radio-alias <3-67>,radio-id,radio-mac,
rx-bytes,rx-errors,rx-packets,rx-throughput,tx-bytes,tx-dropped,tx-packets,
tx-throughput)
customize show-wireless-radio-stats-rf (average-retry-number,error-rate,
noise,q-index,radio-alias <3-67>,radio-id,radio-mac,rx-rate,signal,snr,t-index,
tx-rate)

Parameters

customize [cdp-lldp-info-column-width|hostname-column-width] <1-64>

hostname-column-width <1-64>

Configures default width of the hostname column in all show commands

  • <1-64> – Sets the hostname column width from 1 - 64 characters

cdp-lldp-info-column-width <1-64> Configures the column width in the show > cdp/lldp > [neighbor|report] command output
  • <1-64> – Sets the column width from 1 - 64 characters
customize show-adoption-status (adopted-by,ap-name <1-64>,cdp-lldp-info,
config-status,last-adoption,msgs,uptime,version)
show-adoption-status Configures the information displayed in the show > adoption > status command output. Select the columns (information) displayed from the following options: adopted-by, ap-name, cdp-lldp-info, config-status, last-adoption, msgs, uptime, and version. These are recursive parameters and you can select multiple options at a time.

The columns displayed by default are: Device-Name, Version, Config-Status, MSGS, Adopted-By, Last-Adoption, and Uptime.

Where ever available, you can optionally use the <1-64> parameter to set the column width.

customize show-wireless-client (ap-name <1-64>,auth,client-identity <1-32>,
bss,enc,hostname <1-64>,ip,last-active,location <1-64>,mac,radio-alias <3-67>,
radio-id,radio-type,role <1-32>,state,username <1-64>,vendor,vlan,wlan)

show-wireless-client

Customizes the show > wireless > client command output

The columns displayed by default are: MAC, IPv4, Vendor, Radio-ID, WLAN. VLAN, and State.

ap-name <1-64>

Includes the ap-name column, which displays the name of the AP with which this client associates

  • <1-64> – Sets the ap-name column width from 1 - 64 characters

auth

Includes the auth column, which displays the authorization protocol used by the wireless client

client-identity <1-32>

Includes the client-identity (device type) column, which displays details gathered from DHCP device fingerprinting feature (when enabled). For more information, see client-identity.

  • <1-32> – Sets the client-identity column width from 1 - 32 characters

bss

Includes the BSS column, which displays the BSS ID the wireless client is associated with

enc

Includes the enc column, which displays the encryption suite used by the wireless client

hostname <1-64>

Includes the hostname column, which displays the wireless client's hostname

  • <1-64> – Sets the hostname column width from 1 - 64 characters

ip

Includes the IP column, which displays the wireless client's current IP address

last-active

Includes the last-active column, which displays the time of last activity seen from the wireless client

location <1-64>

Includes the location column, which displays the location of the client's associated Access Points

  • <1-64> – Sets the location column width from 1 - 64 characters

mac

Includes the MAC column, which displays the wireless client's MAC address

radio-alias <3-67>

Includes the radio-alias column, which displays the radio alias with the AP's hostname and radio interface number in the "HOSTNAME:RX" format

  • <3-67 – Sets the radio-alias column width from 3 - 67 characters

radio-id

Includes the radio-id column, which displays the radio ID with the AP's MAC address and radio interface number in the "AA-BB-CC-DD-EE-FF:RX" format

radio-type

Includes the radio-type column, which displays the wireless client's radio type

role <1-32>

Includes the role column, which displays the client's role

  • <1-32> – Sets the role column width from 1 - 32 characters

state

Includes the state column, which displays the wireless client's current availability state

username <1-64>

Includes the username column, which displays the wireless client's username

  • <1-64> – Specify the username column width from 1 - 64 characters.

vendor

Includes the vendor column, which displays the wireless client's vendor ID

vlan

Includes the VLAN column, which displays the wireless client's assigned VLAN

wlan

Includes the WLAN column, which displays the wireless client's assigned WLAN

customize show-wireless-client-stats (hostname <1-64>,mac,rx-bytes,rx-errors,
rx-packets,rx-throughput,t-index,tx-bytes,tx-dropped,tx-packets,tx-throughput)

show-wireless-client-stats

Customizes the show > wireless > client stats command output

The columns displayed by default are: MAC, Tx bytes, RX bytes, Tx pkts, Rx pkts, and Tx bps, RX bps, T-Index, and Dropped pkts.

hostname <1-64>

Includes the hostname column, which displays the wireless client's hostname

  • <1-64> – Sets the hostname column width from 1 - 64 characters

mac

Includes the MAC column, which displays the wireless client's MAC address

rx-bytes

Includes the rx-bytes column, which displays the total number of bytes received by the wireless client

rx-errors

Includes the rx-error column, which displays the total number of errors received by the wireless client

rx-packets

Includes the rx-packets column, which displays the total number of packets received by the wireless client

rx-throughput

Includes the rx-throughput column, which displays the receive throughput at the wireless client

t-index Includes the t-index column, which displays the traffic utilization index at the particular wireless client

tx-bytes

Includes the tx-bytes column, which displays the total number of bytes transmitted by the wireless client

tx-dropped

Includes the tx-dropped column, which displays the total number of dropped packets by the wireless client

tx-packets

Includes the tx-packets column, which displays the total number of packets transmitted by the wireless client

tx-throughput

Includes the tx-throughput column, which displays the transmission throughput at the wireless client

customize show-wireless-client-stats-rf (average-retry-number,error-rate,noise,
q-index,rx-rate,signal,snr,t-index,tx-rate)

show-wireless-client-stats-rf

Customizes the show > wireless > client stats RF command output

The columns displayed by default are: MAC, Signal (dBm), Noise (dBm), SNR (dB), TX Rate (Mbps), Retry Avg, Errors (pps), and Q-Index (%).

average-retry-number

Includes the average-retry-number column, which displays the average number of retransmissions made per packet

error-rate

Includes the error-rate column, which displays the rate of error for the wireless client

hostname <1-64>

Includes the hostname column, which displays the wireless client's hostname

  • <1-64> – Sets the hostname column width from 1 - 64 characters

mac

Includes the MAC column, which displays the wireless client's MAC address

noise

Includes the noise column, which displays the noise (in dBm) as detected by the wireless client

q-index

Includes the q-index column, which displays the RF quality index

Note: Higher values indicate better RF quality.

rx-rate

Includes the rx-rate column, which displays the receive rate at the particular wireless client

signal

Includes the signal column, which displays the signal strength (in dBm) at the particular wireless client

snr

Includes the snr column, which displays the signal-to-noise (SNR) ratio (in dB) at the particular wireless client

t-index

Includes the t-index column, which displays the traffic utilization index at the particular wireless client

tx-rate

Includes the tx-rate column, which displays the packet transmission rate at the particular wireless client

customize show-wireless-meshpoint-accelerated-multicast (ap-hostname,group-addr,
mesh-name,neighbor-hostname,neighbor-ifid,radio-alias,radio-id,radio-mac,subscriptions)
show-wireless-meshpoint-accelerated-multicast Configures the information displayed in the show > wireless > meshpoint > accelerated multicast command output. Select the columns (information) displayed from the following options: ap-hostname, group-addr, mesh-name, neighbor-hostname, neighbor-ifid, radio-alias, radio-id, radio-mac, subscriptions. These are recursive parameters and you can select multiple options at a time.

The columns displayed by default are: Mesh, Radio, Neighbor-IFID, Neighbor-Hostname, Group-MAC, and Subscriptions.

customize show-wireless-meshpoint (ap-mac,cfg-as-root,hops,hostname <1-64>,
interface-ids,is-root,mesh-name <1-64>,mpid,next-hop-hostname <1-64>,next-hop-ifid,
next-hop-use-time,path-metric,root-bound-time,root-hostname <1-64>,root-mpid)

show-wireless-meshpoint

Customizes the show > wireless > meshpoint command output

The columns displayed by default are: Mesh, Hostname, Hops, Is-Root, Config-As-Root, Root-Hostname, Root-Bound-Time, Path-Metric, Next-Hop-Hostname, and Next-Hop-Use-Time.

ap-mac

Includes the ap-mac column, which displays the AP's MAC address in the AA-BB-CC-DD-EE-FF format. Applicable only in case of non-wireless controller meshpoints

cfg-as-root

Includes the cfg-as-root column, which displays the configured root state of the meshpoint

hops

Includes the hops column, which displays the number of hops to the root for this meshpoint

hostname <1-64>

Includes the hostname column, which displays the AP's hostname. Applicable only in case of non-wireless controller meshpoints

  • <1-64> – Sets the hostname column width from 1 - 64 characters

interface-ids

Includes the interface-ids column, which displays the interface identifiers (interfaces used by this meshpoint)

is-root

Includes the is-root column, which displays the current root state of the meshpoint

mesh-name <1-64>

Includes the mesh-name column, which displays the meshpoint's name

  • <1-64> – Sets the mesh-name column width from 1 - 64 characters

mpid

Includes the mpid column, which displays the meshpoint identifier in the AA-BB-CC-DD-EE-FF format

next-hop-hostname <1-64>

Includes the next-hop-hostname column, which displays the next-hop AP's name (the AP next in the path to the bound root)

  • <1-64> – Sets the next-hop-hostname column width from 1 - 64 characters

next-hop-ifid

Includes the next-hop-ifid column, which displays the next-hop interface identifier in the AA-BB-CC-DD-EE-FF format

next-hop-use-time

Includes the next-hop-use-time column, which displays the time since this meshpoint started using this next hop

root-bound-time

Includes the root-bound-time column, which displays the time since this meshpoint has been bound to the current root

root-hostname <1-64>

Includes the root-hostname column, which displays the root AP's hostname to which this meshpoint is bound

  • <1-64> – Sets the root-hostname column width from 1 - 64 characters

root-mpid

Includes the root-mpid column, which displays the bound root meshpoint identifier in the AA-BB-CC-DD-EE-FF format

customize show-wireless-meshpoint-neighbor-stats (ap-hostname <1-64>,
neighbor-hostname <1-64>,neighbor-ifid,rx-bytes,rx-errors,rx-packets,rx-throughput,t-index,
tx-bytes,tx-dropped,tx-packets,tx-throughput)

show-wireless-meshpoint-neighbor-stats

Customizes the show > wireless > meshpoint > neighbor > stats command output

The columns displayed by default are: AP Hostname, Neighbor-IFID, TX bytes, RX bytes, Tx pkts, Rx pkts, Tx (bps), Rx (bps), T-Index (%), and Dropped pkts.

ap-name <1-64>

Includes the ap-name column, which displays name of the AP reporting a neighbor

  • <1-64> – Sets the ap-name column width from 1 - 64 characters

neighbor-hostname <1-64>

Includes the neighbor-hostname column, which displays the reported neighbor's hostname

  • <1-64> – Sets the neighbor-hostname column width from 1 - 64 characters

neighbor-ifid

Includes the neighbor-ifid column, which displays the neighbor's interface ID

rx-bytes

Includes the rx-bytes column, which displays the total bytes received

rx-errors

Includes the rx-error column, which displays the total bytes of error received

rx-packets

Includes the rx-packets column, which displays the number of packets received

rx-throughput

Includes the rx-throughput column, which displays neighbor's received throughput

t-index Includes the t-index column, which displays the traffic utilization index at the neighbor end

tx-bytes

Includes the tx-bytes column, which displays the total bytes transmitted

tx-dropped

Includes the tx-dropped column, which displays the total bytes dropped

tx-packets

Includes the tx-packets column, which displays the number of packets transmitted

tx-throughput

Includes the tx-throughput column, which displays neighbor's transmitted throughput

customize show-wireless-meshpoint-neighbor-stats-rf (ap-hostname <1-64>,
average-retry-number,error-rate,neighbor-hostname <1-64>,neighbor-ifid,noise,
q-index,rx-rate,signal,snr,t-index,tx-rate)

show-wireless-meshpoint-neighbor-stats-rf

Customizes the show > wireless > meshpoint > neighbor > statistics RF command output

The columns displayed by default are: AP Hostname, Neighbor-IFID, Signal (dBm), Noise (dBm), SNR (dB), Tx-Rate (Mbps), Rx-Rate (Mbps), Retry Avg, Errors (pps), and Q-Index (%).

ap-name <1-64>

Includes the ap-name column, which displays name of the AP reporting a neighbor

  • <1-64> – Sets the ap-name column width from 1 - 64 characters

average-retry-number

Includes the average-retry-number column, which displays the average number of retransmissions made per packet.

error-rate

Includes the error-rate column

neighbor-hostname <1-64>

Includes the neighbor-hostname, which displays reported neighbor's hostname

  • <1-64> – Sets the neighbor-hostname column width from 1 - 64 characters

noise

Includes the noise column, which displays the noise level in dBm

q-index

Includes the q-index column, which displays the q-index

rx-rate

Includes the rx-rate column, which displays rate of receiving

signal

Includes the signal column, which displays the signal strength in dBM

snr

Includes the snr column, which displays the signal-to-noise ratio

t-index

Includes the t-index column, which displays t-index

tx-rate

Includes the tx-rate column, which displays rate of transmission

customize show-wireless-mint-client (client-alias <1-64>,client-bss,portal-alias <1-64>,portal-bss,up-time)
show-wireless-mint-client Configures the information displayed in the show > wireless > mint > client command output. Select the columns (information) displayed from the following options: client-alias, client-bss, portal-alias, portal-bss, and up-time. These are recursive parameters and you can select multiple options at a time.

The columns displayed by default are: Portal, Portal-Radio-MAC, Client, Client-Radio-MAC, and Up-Time.

customize show-wireless-mint-client-stats (client-alias <1-64>,portal-alias <1-64>,
portal-bss,rx-bytes,rx-errors,rx-packets,rx-throughput,t-index,tx-bytes,tx-dropped,
tx-packets,tx-throughput)
show-wireless-mint-client-stats Configures the information displayed in the show > wireless > mint > client > statistics command output. Select the columns (information) displayed from the following options: client-alias, portal-alias, portal-bss, rx-bytes, rx-errors, rx-packets, rx-throughput, t-index, tx-bytes, tx-dropped, tx-packets, tx-throughput. These are recursive parameters and you can select multiple options at a time.

The columns displayed by default are: Portal, Portal-Radio-MAC, Client, Tx bytes, Rx bytes, TX pkts, Rx pkts, TX (bps), Rx (bps), T-Index (%), and Dropped pkts.

Where ever available, you can optionally use the <1-64> parameter to set the column width.

customize show-wireless-mint-client-stats-rf (average-retry-number,
client-alias <1-64>,error-rate,noise,portal-alias <1-64>,portal-bss,q-index,rx-rate,
signal,snr,tx-rate)
show-wireless-mint-client-stats-rf Configures the information displayed in the show > wireless > mint > client > statistics > rf command output. Select the columns (information) displayed from the following options: average-retry-number, client-alias, error-rate, noise, portal-alias, portal-bss, q-index, rx-rate, signal, snr, and tx-rate. These are recursive parameters and you can select multiple options at a time.

The columns displayed by default are: MAC, Signal (dBm), Noise (dBm), SNR (dB), Tx-Rate (Mbps), Rx-rate (Mbps), Retry Avg, Errors (pps), and Q-Index (%).

Where ever available, you can optionally use the <1-64> parameter to set the column width.

customize show-wireless-mint-portal (client-alias <1-64>,client-bss,
portal-alias <1-64>,portal-bss,up-time)
show-wireless-mint-portal Configures the information displayed in the show > wireless > mint > portal command output. Select the columns (information) displayed from the following options: client-alias, client-bss, portal-alias, portal-bss, and up-time. These are recursive parameters and you can select multiple options at a time.

The columns displayed by default are: Client, Client-Radio-MAC, Portal, Portal-Radio-MAC, and Up-Time.

Where ever available, optionally use the <1-64> parameter to set the column width.

customize show-wireless-mint-portal-stats-rf (average-retry-number,
client-alias <1-64>,client-bss,error-rate,noise,portal-alias <1-64>,q-index,rx-rate,
signal,snr,tx-rate)
show-wireless-mint-portal-stats-rf Configures the information displayed in the show > wireless > mint > portal > statistics > rf command output. Select the columns (information) displayed from the following options: average-retry-number, client-alias, client-bss, error-rate, noise, portal-alias, q-index, rx-rate, signal, snr, tx-rate. These are recursive parameters and you can select multiple options at a time.

The columns displayed by default are: Client, Client-Radio-MAC, Portal, Signal (dBm), Noise (dBm), SNR (dB), Tx-Rate (Mbps), Rx-rate (Mbps), Retry Avg, Errors (pps), and Q-Index (%).

Where ever available, optionally use the <1-64> parameter to set the column width.

customize show-wireless-radio (adopt-to,ap-name <1-64>,channel,location <1-64>,
num-clients,power,radio-alias <3-67>,radio-id,radio-mac,rf-mode,state)

show-wireless-radio

Customizes the show wireless radio command output

adopt-to

Includes the adopt-to column, which displays information about the wireless controller adopting this AP

ap-name <1-64>

Includes the ap-name column, which displays information about the AP this radio belongs

  • <1-64> – Sets the ap-name column width from 1 - 64 characters

channel

Includes the channel column, which displays information about the configured and current channel for this radio

location <1-64>

Includes the location column, which displays the location of the AP this radio belongs

  • <1-64> – Sets the location column width from 1 - 64 characters

num-clients

Includes the num-clients column, which displays the number of clients associated with this radio

power

Includes the power column, which displays the radio's configured and current transmit power

radio-alias <3-67>

Includes the radio-alias column, which displays the radio's alias (combination of AP's hostname and radio interface number in the "HOSTNAME:RX" formate)

  • <3-67> – Sets the radio-alias column width from 3 - 67 characters

radio-id

Includes the radio-id column, which displays the radio‘s ID (combination of AP's MAC address and radio interface number in the "AA-BB-CC-DD-EE-FF:RX" format)

radio-mac

Includes the radio-mac column, which displays the radio's base MAC address

rf-mode

Includes the rf-mode column, which displays the radio's operating mode. The radio mode can be 2.4 GHz, 5.0 GHz, or sensor.

state

Includes the state column, which displays the radio's current operational state

customize show-wireless-radio-stats (radio-alias <3-67>,radio-id,radio-mac,
rx-bytes,rx-errors,rx-packets,rx-throughput,tx-bytes,tx-dropped,tx-packets,
tx-throughput)

show-wireless-radio-stats

Customizes the show wireless radio statistics command output

radio-alias <3-67>

Includes the radio-alias column, which displays the radio's alias (combination of AP's hostname and radio interface number in the "HOSTNAME:RX" format)

  • <3-67> – Sets the radio-alias column width from 3 - 67 characters

radio-id

Includes the radio-id column, which displays the radio‘s ID (combination of AP's MAC address and radio interface number in the "AA-BB-CC-DD-EE-FF:RX" format)

radio-mac

Includes the radio-mac column, which displays the radio's base MAC address

rx-bytes

Includes the rx-bytes column, which displays the total number of bytes received by the radio

rx-errors

Includes the rx-error column, which displays the total number of errors received by the radio

rx-packets

Includes the rx-packets column, which displays the total number of packets received by the radio

rx-throughput

Includes the rx-throughput column, which displays the receive throughput at the radio

tx-bytes

Includes the tx-bytes column, which displays the total number of bytes transmitted by the radio

tx-dropped

Includes the tx-dropped column, which displays the total number of packets dropped by the radio

tx-packets

Includes the tx-packets column, which displays the total number of packets transmitted by the radio

tx-throughput

Includes the tx-throughput column, which displays the transmission throughput at the radio

customize show-wireless-radio-stats-rf (average-retry-number,error-rate,noise,
-index,radio-alias <3-67>,radio-id,radio-mac,rx-rate,signal,snr,t-index,tx-rate)

show-wireless-radio-stats-rf

Customizes the show wireless radio stats RF command output

average-retry-number

Includes the average-retry-number column, which displays the average number of retransmissions per packet

error-rate

Includes the error-rate column, which displays the rate of error for the radio

noise

Includes the noise column, which displays the noise detected by the radio

q-index

Includes the q-index column, which displays the RF quality index

Higher values indicate better RF quality.

radio-alias <3-67>

Includes the radio-alias column, which displays the radio's alias (combination of AP's hostname and radio interface number in the "HOSTNAME:RX" format)

  • <3-67> – Sets the radio-alias column width from 3 - 67 characters

radio-id

Includes the radio-id column, which displays the radio‘s ID (combination of AP's MAC address and radio interface number in the "AA-BB-CC-DD-EE-FF:RX" format)

radio-mac

Includes the radio-mac column, which displays the radio's base MAC address

rx-rate

Includes the rx-rate column, which displays the receive rate at the particular radio

signal

Includes the signal column, which displays the signal strength at the particular radio

snr

Includes the snr column, which displays the signal-to-noise ratio at the particular radio

t-index

Includes the t-index column, which displays the traffic utilization index at the particular radio

tx-rate

Includes the tx-rate column, which displays the packet transmission rate at the particular radio

Examples

The following example shows the shows the show > adoption > status command output before customizing the output:

rfs4000-229D58#show adoption status
Adopted by:
Type          : nx9000
System Name   : nx9500-6C8809
MAC address   : B4-C7-99-6C-88-09
MiNT address  : 19.6C.88.09
Time          :   4 days 22:38:32 ago

Adopted Devices:
---------------------------------------------------------------------------------------------------------------
DEVICE-NAME       VERSION         CFG-STAT         MSGS ADOPTED-BY        LAST-ADOPTION                  UPTIME
---------------------------------------------------------------------------------------------------------------
ap7532-A2A56C     5.9.2.0-010D   configured No   rfs4000-229D58 4 days 22:25:56     4 days 22:31:23
----------------------------------------------------------------------------------------------------------------
Total number of devices displayed: 1
rfs4000-229D58#
rfs4000-229D58(config)#customize show-adoption-status adopted-by ap-name config-
status last-adoption
rfs4000-229D58(config)#commit

The following example shows the shows the show > adoption > status command output after customizing the output:

rfs4000-229D58#show adoption status
Adopted by:
Type          : nx9000
System Name   : nx9500-6C8809
MAC address   : B4-C7-99-6C-88-09
MiNT address  : 19.6C.88.09
Time 
Adopted Devices:
------------------------------------------------------------------------
ADOPTED-BY        DEVICE-NAME       CFG-STAT         LAST-ADOPTION
------------------------------------------------------------------------
rfs4000-229D58 ap7532-A2A56C    configured        4 days 22:25:56
------------------------------------------------------------------------

Total number of devices displayed: 1
rfs4000-229D58(config)#

Use the no > customize > show-adoption-status command to revert back to the default format.

rfs4000-229D58(config)#no customize show-adoption-status
rfs4000-229D58(config)#commit
rfs4000-229D58#show adoption status
Adopted by:
Type          : nx9000
System Name   : nx9500-6C8809
MAC address   : B4-C7-99-6C-88-09
MiNT address  : 19.6C.88.09
Time          :   4 days 22:38:32 ago

Adopted Devices:
---------------------------------------------------------------------------------------------------------------
DEVICE-NAME       VERSION         CFG-STAT         MSGS ADOPTED-BY        LAST-ADOPTION                  UPTIME
---------------------------------------------------------------------------------------------------------------
ap7532-A2A56C     5.9.2.0-010D configured No   rfs4000-229D58 4 days 22:25:56     4 days 22:31:23
----------------------------------------------------------------------------------------------------------------
Total number of devices displayed: 1
rfs4000-229D58#

Related Commands

no

Restores custom CLI settings to default