show rtep l2pt

show [[{vlan} vlan_name vman_name] {{vxlan {vr vr_name} rtep rtep_ipv4}}] l2pt {detail}

Description

Displays the RTEP L2PT configuration and status of a service.

Syntax Description

vlan Specifies the This command is available on the ExtremeSwitching X440-G2, X450-G2, X460-G2, X465, X590, X620, and X695 series switches. configuration.
vlan_name Specifies the VLAN name.
vxlan Specifies Virtual eXtensible LAN.
vr Specifies Virtual Router.
vr_name Specifies the Virtual Router Name. If not specified, the VR of the current command context is used.
rtep Specifies Remote Tunnel End Point.
rtep_ipv4 Specifies the Remote Tunnel End Point IPv4 address.
l2pt Specifies Layer 2 protocol tunneling.
detail Specifies to show L2PT configuration and status in detail.

Default

N/A.

Usage Guidelines

Use this command to display the RTEP L2PT configuration and status of a service.

Example

The following example illustrates the show rtep l2pt command with RTEP IP address as 2.2.2.2 of VxLAN service Interface:

# show vlan tenant vxlan rtep 2.2.2.2 l2pt
Interface                                        Profile Name
------------------------------------------------ -------------------------------
VR-Default:2.2.2.2                               l2pt-none

The following is an example of the show rtep l2pt command:

# show vlan tenant l2pt
Interface                                        Profile Name
------------------------------------------------ -------------------------------
15                                               l2pt-user
VR-Default:2.2.2.2                               l2pt-none

The following example illustrates the show rept l2pt detail command with RTEP IP address as 2.2.2.2 of VxLAN service Interface:

# show vlan tenant vxlan rtep 2.2.2.2 l2pt detail
VXLAN RTEP: VR-Default:2.2.2.2
    L2PT Profile Name      : l2pt-none
 
    Protocol Filter Name   : cdp
        Destination Address: 01:00:0c:cc:cc:cc
        Protocol Id Type   : snap
        Protocol Id Value  : 0x2000
        Field Offset       :
        Field Value        :
        Field Mask         :
        Action             : None
        CoS                :
        DSCP               : 50
        DSCP Replace       : Yes
        Packets Transmitted: 0
        Packets Received   : 0

The following example illustrates the show rtep l2pt detail command:

# show vlan tenant l2pt detail
Port 15
   L2PT Profile Name      : l2pt-user
 
    Protocol Filter Name   : cdp
        Destination Address: 01:00:0c:cc:cc:cc
        Protocol Id Type   : snap
        Protocol Id Value  : 0x2000
        Field Offset       :
        Field Value        :
        Field Mask         :
        Action             : Tunnel
        CoS                :
        DSCP               : 50
        DSCP Replace       : Yes
        Packets Transmitted: 10956
        Packets Received   : 11492
 
VXLAN RTEP: VR-Default:2.2.2.2
    L2PT Profile Name      : l2pt-none
 
    Protocol Filter Name   : cdp
        Destination Address: 01:00:0c:cc:cc:cc
        Protocol Id Type   : snap
        Protocol Id Value  : 0x2000
        Field Offset       :
        Field Value        :
        Field Mask         :
        Action             : None
        CoS                :
        DSCP               : 50
        DSCP Replace       : Yes
        Packets Transmitted: 0
        Packets Received   : 0

History

This command was first available in ExtremeXOS 31.3.

Platform Availability

This command is supported on the ExtremeSwitching X465, X590, X695 series switches, and stacks with X465, X590, X695 slots only.