Displays the contents of the IP routing table or the route origin priority.
priority | Displays the priority values for each route origin type. |
vlan_name | Specifies a This command is available on the ExtremeSwitching X440-G2, X450-G2, X460-G2, X465, X590, X620, and X695 series switches. name. |
permanent | Specifies permanent routing. |
ip_address | Specifies an IP address. |
netmask | Specifies a subnet mask. |
summary | Displays summary information. |
multicast | Displays information for IPv4 multicast routes only. |
unicast | Displays information for IPv4 unicast routes only. |
vrname | Specifies a VR or VRF. |
N/A.
A c flag in the Flags column indicates a compressed route resulting from enabling compression using the enable iproute compression command. The total number of compressed routes is also shown.
All routes that are provided to the FIB display the f flag.
If you do not specify a VR or VRF, the command applies to the current VR context.
The following example displays detailed information about all IP routing:
# show iproute vr vr-b Ori Destination Gateway Mtr Flags VLAN Duration #d 1.1.1.100/32 1.1.1.100 1 U------um--f- l3vni_vr_b 0d:0h:1m:17s *evn 2.2.2.2/32 2.2.2.2 1 UGHD---u---f- l3vni_vr_b 0d:0h:0m:8s *evn 2.2.2.200/32 2.2.2.2 1 UGHD---u---f- l3vni_vr_b 0d:0h:0m:7s #d 20.1.101.0/24 20.1.101.1 1 U------um--f- tenant_vlan_101 0d:0h:1m:17s *evn 20.1.102.0/24 2.2.2.2 1 UG-D---u---f- l3vni_vr_b 0d:0h:0m:7s *evn 20.1.102.2/32 2.2.2.2 1 UGHD---u---f- l3vni_vr_b 0d:0h:0m:7s *evn 99.0.0.0/8 2.2.2.2 1 UG-D---u---f- l3vni_vr_b 0d:0h:0m:7s Origin(Ori): (ap) Auto-peering, (b) BlackHole, (be) EBGP, (bg) BGP, (bi) IBGP, (bo) BOOTP,(ct) CBT, (d) Direct, (df) DownIF, (dv) DVMRP, (e1) ISISL1Ext, (e2) ISISL2Ext, (evn) EVPN, (h) Hardcoded, (hm) Host-mobility, (i) ICMP,(i1) ISISL1 (i2) ISISL2,(is) ISIS, (mb) MBGP, (mbe) MBGPExt, (mbi) MBGPInter, (mp) MPLS Lsp, (mo) MOSPF (o) OSPF, (o1) OSPFExt1, (o2) OSPFExt2,(oa) OSPFIntra (oe) OSPFAsExt, (or) OSPFInter, (pd) PIM-DM, (ps) PIM-SM, (r) RIP, (ra) RtAdvrt, (s) Static, (sv) SLB_VIP, (un) UnKnown, (*) Preferred unicast route (@) Preferred multicast route, (#) Preferred unicast and multicast route. Flags: (b) BFD protection requested, (B) BlackHole, (c) Compressed, (D) Dynamic, (f) Provided to FIB, (G) Gateway, (H) Host Route, (I) ICMP ping protection requested, (l) Calculated LDP LSP, (L) Matching LDP LSP, (m) Multicast, (p) BFD protection active, (P) LPM-routing, (R) Modified, (s) Static LSP, (S) Static, (t) Calculated RSVP-TE LSP, (T) Matching RSVP-TE LSP, (u) Unicast, (U) Up, (3) L3VPN Route. MPLS Label: (S) Bottom of Label Stack Mask distribution: 1 routes at length 8 2 routes at length 24 4 routes at length 32 Route Origin distribution: 2 routes from Direct 5 routes from EVPN Total number of routes = 7 Total number of compressed routes = 0
This command was first available in ExtremeXOS 10.1.
The ipv4 keyword was added in ExtremeXOS 11.2.
The c flag was added in ExtremeXOS 12.0.
The f flag was added in ExtremeXOS 12.2.2.
The I flag showing ICMP ping protection was added in ExtremeXOS 22.1.
The ap flag showing auto-peering information was added in ExtremeXOS 22.5.
The evn origin prefix showing EVPN information was added in ExtremeXOS 30.7.
This command is available on ExtremeSwitching X435, X440-G2, X450-G2, X460-G2, X465, X590, X620, and X695 series switches.