Route Policy Definition

You can define an IP route policy and its attributes globally, and then apply them individually to interfaces and protocols. You can also form a unified database of route policies that the RIP or OSPF protocol can use for type of filtering purpose. A name or ID identifies a policy.

Under a policy you can have several sequence numbers. If you do not configure a field in a policy, the system displays the field as 0 in CLI show command output. This value indicates that the device ignores the field in the match criteria. Use the clear option to remove existing configurations for the field.

Each policy sequence number contains a set of fields. Only a subset of those fields is used when the policy is applied in a certain context. For example, if a policy has a configured set-preference field, it is used only when the policy is applied for accept purposes. This field is ignored when the policy is applied for announce or redistribute purposes.

You can only apply one policy for each purpose (RIP Announce, for example) on a given RIP interface. In this case, all sequence numbers under the policy apply to that filter. A sequence number also acts as an implicit preference; a lower sequence number is preferred.

The following tables display the accept, announce, and redistribute policies for RIP, OSPF, IS-IS and BGP. The tables also display which matching criteria apply for a certain routing policy. In these tables, 1 denotes advertise router, 2 denotes RIP gateway, and 3 denotes that external type 1 and external type 2 are the only options.

Note

The route policies treat permit and deny rules differently for inbound and outbound traffic.

For an in-policy (RIP, BGP) or an accept policy (OSPF) using a route-map, if a particular route is not explicitly denied in the accept policy or in-policy with the route-map, then the route is implicitly allowed.
For an out-policy (RIP, BGP) or a redistribute policy (RIP, OSPF, BGP) using a route-map, even if a particular route is not explicitly allowed in the redistribution policy or out-policy with the route-map, then the route is implicitly denied.
In order to permit or deny only explicit routes, configure a policy with additional sequences, where, the last sequence permits all routes that are not explicitly permitted or denied.

Note

IPv4 and IPv6 route-maps cannot be configured on the same match statement.

Table 1. Protocol route policy table for RIP
	Announce				Accept
	OSPF	Direct	RIP	BGP	RIP
Match Protocol	Yes	Yes	Yes	Yes
Match Network	Yes	Yes	Yes	Yes	Yes
Match IpRoute Source	Yes¹		Yes²
Match NextHop	Yes	Yes	Yes	Yes	Yes
Match Interface			Yes
Match Route Type	Yes
Match Metric	Yes	Yes	Yes	Yes	Yes
MatchAs Path
Match Community
Match Community Exact
MatchTag				Yes
NssaPbit
SetRoute Preference					Yes
SetMetric TypeInternal
SetMetric	Yes	Yes	Yes	Yes	Yes
SetMetric Type
SetNextHop
SetInject NetList	Yes	Yes	Yes	Yes	Yes
SetMask					Yes
SetAsPath
SetAsPath Mode
Set Automatic Tag
Set CommunityNumber
Set CommunityMode
SetOrigin
SetLocal Pref
SetOrigin EgpAs
SetTag
SetWeight

Table 2. Protocol route policy table for OSPF
	Redistribute					Accept
	Direct	Static	RIP	BGP	IS-IS	OSPF
Match Protocol				Yes	Yes
Match Network	Yes	Yes	Yes	Yes	Yes	Yes
Match IpRoute Source			Yes²
Match NextHop		Yes	Yes	Yes
Match Interface			Yes
Match Route Type					Yes³
Match Metric	Yes	Yes	Yes	Yes	Yes	Yes
MatchAs Path
Match Community
Match Community Exact
MatchTag				Yes
Set NSSA Bit	Yes	Yes	Yes	Yes	Yes
SetRoute Preference
SetMetric TypeInternal
SetMetric	Yes	Yes	Yes	Yes	Yes	Yes
SetMetric Type	Yes	Yes	Yes	Yes	Yes
SetNextHop				Yes
Set Inject NetList	Yes	Yes	Yes	Yes	Yes	Yes
SetMask
SetAsPath
SetAsPath Mode
Set Automatic Tag
Set CommunityNumber
Set CommunityMode
SetOrigin
SetLocal Pref
SetOrigin EgpAs
SetTag
SetWeight

Table 3. Protocol route policy table for IS-IS
	Redistribute				Accept
	Direct	Static	RIP	BGP	OSPF
Match Protocol	Yes	Yes	Yes	Yes	Yes
Match Network	Yes	Yes	Yes	Yes	Yes
Match IpRoute Source			Yes
Match NextHop		Yes	Yes	Yes	Yes
Match Interface			Yes
Match Route Type					Yes³
Match Metric	Yes	Yes	Yes	Yes	Yes
MatchAs Path
Match Community
Match Community Exact
MatchTag				Yes
Set NSSA Bit
SetRoute Preference
SetMetric Type Internal
SetMetric	Yes	Yes	Yes	Yes	Yes
SetMetric Type	Yes	Yes	Yes	Yes	Yes
SetNextHop				Yes
SetInject NetList	Yes	Yes	Yes	Yes	Yes
SetMask
SetAsPath
SetAsPath Mode
Set Automatic Tag
Set CommunityNumber
Set CommunityMode
SetOrigin
SetLocal Pref
SetOrigin EgpAs
SetTag
SetWeight

Table 4. Protocol route policy table for BGP
	Redistribute			Accept	Announce
	IPv6 Direct	IPv6 Static	OSPFv3	BGP	BGP
Match as-path				Yes	Yes
Match community	Yes	Yes	Yes	Yes	Yes
Match community-exact				Yes	Yes
Match extcommunity				Yes	Yes
Match interface
Match local-preference
Match metric	Yes	Yes	Yes	Yes	Yes
Match network	Yes	Yes	Yes	Yes	Yes
Match next-hop		Yes	Yes	Yes	Yes
Match protocol
Match route-source				Yes
Match route-type			Yes		Yes
Match tag
Match vrf
Match vrfids
Set as-path				Yes	Yes
Set as-path-mode				Yes	Yes
Set automatic-tag
Set community				Yes	Yes
Set community-mode				Yes	Yes
Set injectlist	Yes	Yes	Yes
Set ip-preference
Set local-preference				Yes	Yes
Set mask
Set metric	Yes	Yes	Yes	Yes	Yes
Set metric-type
Set metric-type-internal
Set next-hop				Yes	Yes
Set nssa-pbit
Set origin					Yes
Set origin-egp-as
Set Tag
Set Weight				Yes