event

Configures an event and sets the action performed when the event happens

Supported on the following devices:

Access Points: AP3000/X, AP5010, AP310i/e, AP410i/e, AP505i, AP510i, AP510e, AP560i, AP7602, AP7612, AP7622, AP7632, AP7662, AP8163, AP8533.
Service Platforms: NX5500, NX7500, NX9500, NX9600
Virtual Platforms: CX9000, VX9000

Syntax

event <EVENT-TYPE> <EVENT-NAME> (email,forward-to-switch,snmp,syslog) [default|on|off]

The even types are:

nx9500-6C8809(config-event-system-policy-testpolicy)#event ?
  aaa             AAA/Radius module
  adapt           Adaptivity Module 
  adopt-service   Adoption Service
  adv-wips        Adv-wips module 
  ap              Access Point module
  bonjgw          Bonjgw module
  bt              Bluetooth
  captive-portal  Captive Portal
  cdp             Cisco Discovery Protocol
  certmgr         Certificate Manager (Not valid for NCAP/MCN)  
  cfgd            Cfgd module
  cluster         Cluster module
  crm             Critical Resource Monitoring
  database        Database Services
  device          Device module
  dhcpsvr         DHCP Configuration Daemon
  diag            Diag module
  dot11           802.11 management module
  dot1x           802.1X Authenticationn
  fa              Fabric Attach
  fwu             Firmware update module
  isdn            Isdn module
  l2gre           Layer 2 GRE Tunnel
  l2tpv3          Layer 2 Tunneling Protocol Version 3
  licmgr          License module
  lldp            Link Layer Discovery Protocol
  mesh            Mesh module
  mgmt            Management Services
  nsm             Network Services Module
  pm              Process-monitor module
  radconf         Radius Configuration Daemon
  rasst           Roaming-Assist module
  radio           Radio module
  smrt            Smart-rf module
  smtpnot         Smtpnot module
  system          System module
  test            Test module
  vrrp            Virtual Router Redundancy Protocol
  webf            Webf module
  wips            Wireless IPS module

nx9500-6C8809(config-event-system-policy-testpolicy)#

Note

The parameter values for <EVENT-TYPE> and <EVENT-NAME> are summarized in the table under the Parameters section.

Parameters

event <EVENT-TYPE> <EVENT-NAME> (email,forward-to-switch,snmp,syslog) [default|on|off]


<event-type>	<event-name>
aaa	Enables and configures logging of the following authentication, authorization, and accounting related events: radius-discon-msg – RADIUS disconnection message radius-session-expired – RADIUS session expired message radius-session-not-started – RADIUS session not started message radius-vlan-update – RADIUS VLAN update message
adapt	Enables and configures logging of the following adaptivity module related events: adaptivity-change – Event adaptivity change adaptivity-rehome – Event adaptivity rehome
adopt-services	Enables and configures the logging of adopted services related events
adv-wips	Enables and configures the logging of advanced WIPS related events
ap	Enables and configures logging of the following AP related events: adopted – Event AP adopted adopted-to-controller – Event AP adopted to wireless controller ap-adopted – Event access port adopted ap-autoup-done – Event AP autoup done ap-autoup-fail – Event AP autoup fail ap-autoup-needed – Event AP autoup needed ap-autoup-no-need – Event AP autoup not needed ap-autoup-reboot – Event AP autoup reboot ap-autoup-timeout – Event AP autoup timeout ap-autoup-ver – Event AP autoup version ap-reset-detected – Event access port reset detected ap-reset-request – Event access port user requested reset ap-timeout – Event access port timed out ap-unadopted – Event access port unadopted image-parse-failure – Event image parse failure legacy-auto-update – Event legacy auto update no-image-file – Event no image file offline – Event AP detected as offline online – Event offline AP detected as online reset – Event reset sw-conn-lost – Event software connection lost unadopted – Event unadopted
bt	Enables and configures logging of the following bluetooth related events: bt-started – Event bluetooth (bt) started bt-state-change – Event bt state change
captive-portal	Enables and configures logging of the following captive portal (hotspot) related events: allow-access – Event client allowed access auth-failed – Event client authentication failed auth-success – Event client authentication success client-disconnect – Event client disconnected client-removed – Event client removed data-limit-exceed – Event client data limit exceeded flex-log-access – Event flexible log access granted to client inactivity-timeout – Event client time-out due to inactivity page-cre-failed – Event page creation failure purge-client – Event client purged session-timeout – Event session timeout vlan-switch – Event client switched VLAN
cdp	Enables and configures logging of the following CISCO Discovery Protocol (CDP) related event: duplex-mismatch – Event duplex mismatch detected between CDP neighbors
certmgr	Enables and configures logging of the following certificate manager related events: ca-cert-actions-failure – Event CA certificate actions failure ca-cert-actions-success – Event CA certificate actions success ca-key-actions-failure – Event CA key actions failure ca-key-actions-success – Event CA key actions success cert-expiry – Event certificate expiry crl-actions-failure – Event Certificate Revocation List (CRL ) actions failure crl-actions-success – Event CRL actions success csr-export-failure – Event CSR export failure csr-export-success – Event CSR export success delete-trustpoint-action – Event delete trustpoint action export-trustpoint – Event trustpoint exported import-trustpoint – Event trustpoint imported rsa-key-actions-failure – Event RSA key actions failure rsa-key-actions-success – Event RSA key actions success svr-cert-actions-success – Event server certificate actions success svr-cert-actions-failure – Event server certificate actions failure
certmgr-lite	Enables and configures logging of certificate manager (lite version) related event messages
cfgd	Enables and configures logging of the following configuration daemon module related events: acl-attached-altered – Event Access List (ACL) attached altered acl-rule-altered – Event ACL rule altered
cluster	Enables and configures logging of the following cluster module related events: cmaster-cfg-update-fail – Event cluster master config update failed max-exceeded – Event maximum cluster count exceeded state-change – Event cluster state change (active/inactive) state-change-active – Event cluster state change to active state-change-inactive – Event cluster state change to inactive state-retain-active – Event cluster state retained as active
crm	Enables and configures logging of the following Critical Resource Monitoring (CRM) related event critical-resource-down – Event critical resource goes down critical-resource-up – Event critical resource comes up
device	Enables and configures the logging of device module related events
database	Enables and configures logging of the following error conditions in the captive-portal/NSIght database: database-election-fail – Event primary database node selection failure. Requires manual intervention to select primary database node. database-exception – Event database may need to be dropped and device restarted database-low-disk-space – Event database low disk space database-new-state – Event database state change database-op-failure – Event database failure database-set-name-mismatch – Event replica-set not enabled on host database-storage-mismatch – Event database mismatch. All database files must be removed. operation-complete – Event database operation completed successfully operation-failed – Event database operation failure
dhcpsvr	Enables and configures logging of the following DHCP server related events: dhcp-start – Event DHCP server started dhcpsvr-stop – Event DHCP sever stopped relay-iface-no-ip – Event no IP address on DHCP relay interface relay-no-iface – Event no interface for DHCP relay relay-start – Event relay agent started relay-stop – Event DHCP relay agent stopped
diag	Enables and configures logging of the following diagnostics module related events: autogen-tech-sprt – Event autogen technical support buf-usage – Event buffer usage cpu-load – Event CPU load cpu-usage-too-high – Event CPU usage high cpu-usage-too-high-recovery – Event recovery from high CPU usage disk-usage – Event disk usage elapsed-time – Event elapsed time fan-underspeed – Event fan underspeed fd-count – Event forward count free-flash-disk – Event free flash disk free-flash-inodes – Event free flash inodes free-nvram-disk – Event free nvram disk free-nvram-inodes – Event free nvram inodes free-ram – Event free ram free-ram-disk – Event free ram disk free-ram-inodes – Event free ram inodes head-cache-usage – Event head cache usage high-temp – Event high temp ip-dest-usage – Event ip destination usage led-identify – Event led identify low-temp – Event low temp mem-usage-too-high – Event memory usage high mem-usage-too-high-recovery – Event recovery from high memory usage new-led-state – Event new led state over-temp – Event over temp over-voltage – Event over voltage poe-init-fail – Event PoE init fail poe-power-level – Event PoE power level poe-read-fail – Event PoE read fail poe-state-change – Event PoE state change poe-state-change – Event PoE state change pwrsply-fail – Event failure of power supply raid-degraded – Event Redundant Array of Independent Disks (RAID) degraded raid-error – Event RAID error ram-usage – Event ram usage under-voltage – Event under voltage wd-reset-sys – Event wd reset system wd-state-change – Event wd state change
dot11	Enables and configures logging of the following 802.11 management module related events: client-assoc-ignored – Wireless client association ignored event client-associated – Wireless client associated event client-denied-assoc – Event client denied association client-disassociated – Wireless client disassociated country-code – Event country code applied country-code-error – Event country code error eap-cached-keys – Event Extensible Authentication Protocol (EAP) cached keys eap-client-timeout – Event EAP client timeout eap-failed – Event EAP failed eap-opp-cached-keys – Event EAP opp cached keys eap-preauth-client-timeout – Event EAP pre authentication client timeout eap-preauth-failed – Event EAP pre authentication failed eap-preauth-server-timeout – Event EAP pre authentication server timeout eap-preauth-success – Event EAP pre authentication success eap-server-timeout – Event EAP server timeout eap-success – Event EAP success ft-roam-success – Event client fast BSS transition gal-rx-request – Event GAL request received event gal-tx-response – Event response sent to GAL request gal-validate-failed – Event GAL validation failed gal-validate-req – Event GAL validation request gal-validate-success – Event GAL validation success kerberos-client-success – Event client Kerberos authentication success kerberos-wlan-failed – Event WLAN Kerberos authentication failed kerberos-wlan-success – Event WLAN Kerberos authentication success kerberos-wlan-timeout – Event Kerberos authentication timed out move-operation-success – Event move operation success tkip-cntrmeas-end – Event TKIP countermeasures ended tkip-cntrmeas-start – Event TKIP countermeasures initiated tkip-mic-fail-report – Event TKIP MIC failure report tkip-mic-failure – Event TKIP MIC check failed neighbor-denied-assoc – Event neighbor denied association unsanctioned-ap-active – Event unsanctioned AP active unsanctioned-ap-inactive – Event unsanctioned AP inactive unsanctioned-ap-status-change – Event unsanctioned AP status change voice-call-completed – Event voice call completed voice-call-established – Event voice call established voice-call-failed – Event voice call failed wlan-time-access-disable – Event WLAN disabled by time-based-access wlan-time-access-enable – Event WLAN re-enabled by time-based-access wpa-wpa2-failed – Event WPA-WPA2 failed wpa-wpa2-key-rotn – Event WPA-WPA2 key rotn wpa-wpa2-success – Event WPA-WPA2 success
dot1x	Enables and configures logging of the following 802.1X authentication related events: dot1x-failed – Event EAP authentication failure dot1x-success – Event dot1x-success
fa	Enables and configures logging of fabric attach related events: fa-accepted – Event fa-accepted fa-pending – Event fa-pending
fwu	Enables and configures logging of the following firmware update (FWU) related events: fwuaborted – Event fwu aborted fwubadconfig – Event fwu aborted due to bad config fwucorruptedfile – Event fwu aborted due to corrupted file fwucouldntgetfile – Event fwu aborted because the system could not get file fwudone – Event fwu done fwufileundef – Event fwu aborted due to file undefined fwunoneed – Event fwu no need fwuprodmismatch – Event fwu aborted due to product mismatch fwuserverundef – Event fwu aborted due to server undefined fwuserverunreachable – Event fwu aborted due to server unreachable fwusignmismatch – Event fwu aborted due to signature mismatch fwusyserr – Event fwu aborted due to system error fwuunsupportedhw – Event fwu aborted due to unsupported hardware fwuunsupportedmodelnum – Event fwu aborted due to unsupported FIPS model number fwuvermismatch – Event fwu aborted due to version mismatch
isdn	Configures file Integrated Service Digital Network (ISDN) module related event s isdn-alert – Event ISDN alert isdn-crit – Event ISDN critical isdn-debug – Event ISDN debug isdn-emerg – Event ISDN emergency isdn-err – Event ISDN error isdn-info – Event ISDN info isdn-notice – Event ISDN notice isdn-warning – Event ISDN warning
l2gre	Enables and configures logging of the following Layer 2 GRE (L2GRE) tunnel related events: l2gre-tunnel-down – Event L2GRE tunnel down l2gre-tunnel-failover – Event L2GRE tunnel failover l2gre-tunnel-up – Event L2GRE tunnel up
l2tpv3	Enables and configures logging of the following Layer 2 TPV3 (L2TPv3) tunnel related events: l2tpv3-tunnel-down – Event L2TPv3 tunnel down l2tpv3-tunnel-up – Event L2TPv3 tunnel up
licmgr	Enables and configures logging of the following license manager module related events: lic-installed-count – Event total number of license installed count lic-installed-default – Event default license installation lic-installed – Event license installed lic-invalid – Event license installation failed lic-removed – Event license removed
lldp	Enables and configures logging of the following Link Layer Discovery Protocol (LLDP) related events: lldp-loop-detected – Event layer 2 switching loop lldp-loop-recovery – Event recovery from layer 2 switching loop
mgmt	Enables and configures logging of the following management services module related events: log-http-init – Event Web server started log-http-local-start – Event Web server started in local mode log-http-start – Event Web server started in external mode log-https-start – Event secure Web server started log-https-wait – Event waiting for Web server to start log-key-deleted – Event RSA key associated with SSH is deleted log-key-restored – Event RSA key associated with SSH is added log-trustpoint-deleted – Event trustpoint associated with HTTPS is deleted
mesh	Enables and configures logging of the following mesh module related events: mesh-link-down – Event mesh link down mesh-link-up – Event mesh link up meshpoint-down – Event meshpoint down meshpoint-loop-prevent-off – Event meshpoint loop prevent off meshpoint-loop-prevent-on – Event meshpoint loop prevent on meshpoint-path-change – Event meshpoint-path-change meshpoint-root-change – Event meshpoint-root-change meshpoint-up – Event meshpoint up
nsm	Configures Network Service Module (NSM) related event dhcpc-err – Event DHCP certification error dhcpdefrt – Event DHCP defrt dhcpip – Event DHCP IP dhcpipchg – Event DHCP IP change dhcpipnoadd – Event DHCP IP overlaps static IP address dhcplsexp – Event DHCP lease expiry dhcpnak – Event DHCP server returned DHCP NAK response dhcpnodefrt – Event interface no default route if-failback – Event interface failback if-failover – Event interface failover ifdown – Event interface down ifipcfg – Event interface IP config ifup – Event interface up nsm-ntp – Event translate host name
pm	Configures process monitor module related event s procid – Event proc ID generated procmaxrstrt – Event proc max restart procnoresp – Event proc no response procrstrt – Event proc restart procstart – Event proc start procstop – Event proc stop procsysrstrt – Event proc system restart startupcomplete – Event startup complete
radconf	Enables and configures logging of the following RADIUS configuration daemon related events: could-not-stop-radius – Event could not stop RADIUS server radiusdstart – Event RADIUS server started radiusdstop – Event RADIUS server stopped
radio	Enables and configures logging of the following radio module related events: acs-scan-complete – Event ACS scan completed acs-scan-started – Event ACS scan started cb-associated – Event client-bridge access point associates with an infrastructure access point cb-roam – Event client-bridge access point roams from one infrastructure access point to another infrastructure access point cb-wired-client-added – Event wired client is added to the client-bridge cb-wired-client-removed – Event wired client is removed from the client-bridge channel-country-mismatch – Event channel and country of operation mismatch radar-det-info – Detected radar info radar-detected – Event radar detected radar-scan-completed – Event radar scan completed radar-scan-started – Event radar scan started radio-antenna-error – Event invalid antenna type on this radio radio-antenna-setting – Event antenna type setting on this radio radio-state-change – Event radio state change resume-home-channel – Event resume home channel
rasst	Enables and configures the logging of roaming assist module related events
smrt	Enables and configures logging of the following SMART RF module related events: calibration-done – Event calibration done calibration-started – Event calibration started channel-change – Event channel change config-cleared – Configuration cleared event cov-hole-recovery – Event coverage hole recovery cov-hole-recovery-done – Event coverage hole recovery done interference-recovery – Event interference recovery neighbor-recovery – Event neighbor recovery power-adjustment – Event power adjustment root-recovery – Event meshpoint root recovery
smtpnot	Enables and configures logging of the following SMTP module related events: cfg – Event cfg cfginc – Event cfg inc net – Event net proto – Event proto smtpauth – Event SMTP authentication smtperr – Event SMTP error smtpinfo – Event SMTP information
system	Enables and configures logging of the following system module related events: clock-reset – Event clock reset cold-start – Event cold start config-commit – Event configuration commit config-revision – Event config-revision done devup-rfd-fail – Event device-upgrade failed on rf-domain manager managed devices guest-user-exp – Event guest user purging http-err – Event Web server did not start login – Event successful login login-fail – Event login fail. Occurs when user authentication fails. login-fail-access – Event login fail access. Occurs in case of access violation. login-fail-bad-role – Event login fail bad role. Occurs when user uses an invalid role to logon. login-lockout – Event user account locked out message. Occurs when a user account is locked due to exceeding of maximum number failed login attempts threshold. Configure this event notification only if the max-fail and lockout-time parameters have been configured in the management-policy context. For more information, see password-entry. login-unlocked – Event user account un-locked. Occurs when a locked user account is re-activated. Enable this event notification only if the max-fail and lockout-time parameters have been configured in the management-policy context. For more information, see password-entry. logout – Event logout maat-light – Event action on RIM (Research in Motion) radio(s) from the Maat light module panic – Event panic periodic-heart-beat – Event periodic heart beat procstop – Event proc stop server-unreachable – Event server-unreachable system-autoup-disable – Event system autoup disable system-autoup-enable – Event system autoup enable t5-config-error – Event t5-config-error ui-user-auth-fail – Event user authentication fail ui-user-auth-success – Event user authentication success warm-start – Event warm start warm-start-recover – Event recovery from warm start
test	Enables and configures logging of the following test module related events: testalert – Event test alert testargs – Event test arguments testcrit – Event test critical testdebug – Event test debug testemerg – Event test emergency testerr – Event test error testinfo – Event test information testnotice – Event test notice testwarn – Event test warning
vrrp	Enables and configures logging of the following Virtual Router Redundancy Protocol (VRRP) related events: vrrp-monitor-change – Event VRRP monitor link state change vrrp-state-change – Event VRRP state transition vrrp-vip-subnet-mismatch – Event VRRP IP not overlapping with an interface addresses
webf	Enables and configures logging of the following Web Filtering (webf) module related events: malform-url-request – Event malformed URL request no-parent-engine – Event ‘no session to URL classification server‘ srvr-connect-fail – Event URL classification server unreachable url-blocked – Event URL blocked webf-lic-acquired – Event webf license acquired webf-lic-missing – Event webf license missing webf-lic-revoked – Event webf license revoked
wips	Enables and configures logging of the following Wireless IPS module related events: air-termination-active – Event air termination active air-termination-ended – Event air termination ended air-termination-inactive – Event air termination inactive air-termination-initiated – Event air termination initiated rogue-ap-active – Event rogue AP active rogue-ap-inactive – Event rogue AP inactive unsanctioned-ap-active – Event unsanctioned AP active unsanctioned-ap-inactive – Event unsanctioned AP inactive unsanctioned-ap-status-change – Event unsanctioned AP changed state wips-client-blacklisted – Event WIPS client blacklisted wips-client-rem-blacklist – Event WIPS client rem blacklist wips-event – Event WIPS event triggered Note: Air-termination is not supported on AP505 and AP510 model access points.
email	Sends e-mail notifications to a pre configured e-mail ID
forward-to-switch	Forwards the messages to an external server
snmp	Logs an SNMP event
syslog	Logs an event to syslog
default	Performs the default action for the event
off	Switches the event off, when the event happens, and no action is performed
on	Switches the event on, when the event happens, and the configured action is taken

Examples

rfs4000-229D58(config-event-system-policy-event-testpolicy)#event aaa radius-discon-msg email on forward-to-switch default snmp default syslog default

rfs4000-229D58(config-event-system-policy-testpolicy)#show context
event-system-policy test
 event aaa radius-discon-msg email on
rfs4000-229D58(config-event-system-policy-testpolicy)#

nx9500-6C8809(config-event-system-policy-test)#event database database-exception
 syslog default snmp default forward-to-switch default email default

nx9500-6C8809(config-event-system-policy-test)#event database operation-failed syslog default snmp default forward-to-switch default email default

nx9500-6C8809(config-event-system-policy-test)#show context include-factory | grep operation-failed
 event database operation-failed syslog default snmp default forward-to-switch default email default
nx9500-6C8809(config-event-system-policy-test)#

Related Commands


no (event-system-policy-config-mode)	Resets or disables event monitoring