WiNG Event Messages

Event

Description

ADOPT-SERVICE SNMP_SUCCESS 6

SNMP framework success

ADOPT-SERVICE SNMP_FAILURE 6

SNMP framework failure

ADOPT-SERVICETUT_TEMPERATURE_ALARM_RAISED ([str])

Temperature alarm raised on sensor

ADOPT-SERVICE TUT_TEMPERATURE_ALARM_CLEARED ([str])

Temperature alarm cleared on sensor

ADOPT-SERVICE TUT_TEMPERATURE_ALARM_CLEARED ([str])

Temperature alarm cleared on sensor

ADOPT-SERVICE TUT_FAN_ALARM_CLEARED 5 IPX ([str])

Fan alarm cleared on ID

ADOPT-SERVICE TUT_PWRCTRL_ALARM_RAISED 5 IPX ([str])

Power controller alarm raised

ADOPT-SERVICE TUT_PWRCTRL_ALARM_CLEARED 5 IPX ([str])

Power controller alarm cleared

ADOPT-SERVICE TUT_LINE_POWER_ALARM_RAISED 5 IPX ([str]) Line power alarm raised on id [str]

Line power alarm raised

ADOPT-SERVICE TUT_LINE_POWER_ALARM_CLEARED 5 IPX ([str]) Line power alarm cleared on id [str]

Line power alarm cleared

ADOPT-SERVICE TUT_WLAN_CLIENT_ASSOC 6 IPX ([str]) Client [str] on interface index [str] associated

Client associated

ADOPT-SERVICE TUT_WLAN_CLIENT_DISASSOC 6 IPX ([str]) Client [str] on interface index [str] disassociated with status code [str], [str]

Client disassociated

ADOPT-SERVICE TUT_WLAN_CLIENT_ASSOC_FAILURE 3 IPX ([str]) Association failed for Client [str] on interface index [str] with status code [str], [str]

Association failed for client on specified interface index

ADOPT-SERVICE TUT_WLAN_CLIENT_AUTH 6 IPX ([str])

Client on interface index authenticated

ADOPT-SERVICE TUT_WLAN_CLIENT_DEAUTH 6 IPX ([str])

Client on interface index deauthenticated with status code

ADOPT-SERVICE TUT_WLAN_CLIENT_AUTH_FAILURE 3 IPX ([str])

Authentication failed for client on interface index with status code

ADOPT-SERVICE TUT_RADIO_ADAPTIVE_POWER_CHANGE 5 IPX ([str])

Interface with operational status and power levels

ADOPT-SERVICE TUT_RF_MONITOR_MODE_CHANGE 5 IPX ([str])

RF monitor status changed to on interface

ADOPT-SERVICE IPX_EVENT_FAILURE 3 IPX ([str])

Failed to raise WiNG event

AP NO_IMAGE_FILE [str] firmware image is not present on controller

Access Point firmware not on controller

AP IMAGE_PARSE_FAILURE Format of [str] firmware image on controller is invalid

Invalid Access Point firmware file

AP LEGACY_AUTO_UPDATE Legacy Access Point [str] [mac] being updated

Legacy Access Point updated

AP AP_ADOPTED [str] [mac] adopted

Access Point adopted

AP AP_UNADOPTED [str] [mac] un-adopted

Access Point unadopted

AP AP_RESET_DETECTED 6 [str] [mac] reset itself

Access Point reset detected

AP AP_RESET_REQUEST 6 [str] [mac] reset request

Access Point user requested reset

AP AP_TIMEOUT 6 str] [mac] timed out, reset sent to AP

Access Point timed out

AP ADOPTED Access Point([qstr]/[qstr]/[dev]) at rf-domain:[qstr] adopted and configured. Radios: Count=[str], Bss: [str]

Access Point adopted and configured

AP UNADOPTED Access Point([qstr]/[qstr]/[dev]) at rf-domain:[qstr] unadopted. Radios: Count=[str], Bss: [str]

Access Point unadopted

AP ADOPTED_TO_CONTROLLER Joined successfully with controller [qstr]([str])

Access Point adopted to controller

AP ONLINE Access Point [dev] is now online. Offline Reason is [str]. Offline count is [int]

Access Point online

AP OFFLINE Access Point [dev] is now offline. Offline Reason is [str]. Offline count is [int]

Access Point offline

AP OFFLINE Device [dev]([str]) is offline, last seen:[int] minutes ago on switchport [str]

Adopted device offline

AP RESET Reset Access Point mac [dev], [str]

Access Point reset

AP ADOPTION_REDIRECTED Access Point([qstr]/[qstr]/[dev]) cdp:[qstr] lldp:[qstr] redirected to the controller host/pair [qstr] - [qstr]

Access Point redirected

AP AP_AUTOUP_TIMEOUT 4 AUTOUPGRADE: [str] mac [str] Autoupgrade timed out

Time out while auto upgrading an AP

AP AP_AUTOUP_REBOOT 5 AUTOUPGRADE: [str] mac [str] Autoupgrade rebooting

Rebooting AP after upgrade

AP AP_AUTOUP_NO_NEED 6 AUTOUPGRADE: [str] mac [str] ver [str] Autoupgrade not required or not available

Auto upgrade not initiated

AP AP_AUTOUP_NEEDED 6 AUTOUPGRADE: [str] mac [str] ver [str] Autoupgrade will be applied

Auto upgrade is initiated on AP

AP AP_AUTOUP_DONE 5 AUTOUPGRADE: [str] mac [str] Autoupgrade complete

Auto upgrade successful

AP AP_AUTOUP_FAIL 4 AUTOUPGRADE: [str] mac [str] Autoupgrade failed

Failed auto upgrade attempt

AP AP_AUTOUP_VER 6 AUTOUPGRADE: version [str] available for [str] equipment

Available Access Point firmware versions for auto upgrade

AAA RADIUS_DISCON_MSG Received Radius dynamic authorization Disconnect Message for [qstr] from server [qstr]

Received RADIUS disconnect request

AAA RADIUS_VLAN_UPDATE6 Assigning Radius server specified vlan [uint] to client [qstr] on wlan [qstr]

Client VLAN updated by RADIUS

AAA RADIUS_SESSION_NOT_STARTED5 Radius server indicates session time has not started for client [qstr]

Start time from RADIUS resource not yet valid

AAA RADIUS_SESSION_EXPIRED5 Radius server indicates session has already expired for client [qstr]

Session time from RADIUS resource already expired

ADV-WIPS ADV-WIPS-EVENT-1 4 Detected DoS Deauthentication attack against [mac] [str]

DoS Deauthentication attack

ADV-WIPS ADV-WIPS-EVENT-2 4 Detected DoS Disassociation attack against [mac] [str]

DoS disassociation attack

ADV-WIPS ADV-WIPS-EVENT-3 4 Detected DoS EAP failure spoof attack by [mac] [str]

EAP failure spoof attack

ADV-WIPS ADV-WIPS-EVENT-10 4 Detected ID-Theft out of sequence attack for [mac] [str]

ID theft out of sequence attack

ADV-WIPS ADV-WIPS-EVENT-11 4 Detected possible ID-Theft EAPoL Success spoof attack by [mac] [str]

Possible ID theft EAPoL success spoof attack

ADV-WIPS ADV-WIPS-EVENT-12 4 Detected possible WLAN-Jack attack by [mac] [str]

Possible WLAN jack attack

ADV-WIPS ADV-WIPS-EVENT-13 4 Detected possible ESSID-Jack attack against [mac] [str]

Possible ESSID jack attack

ADV-WIPS ADV-WIPS-EVENT-14 4 Detected possible Monkey-Jack attack by [mac] [str]

Possible monkey jack attack

ADV-WIPS ADV-WIPS-EVENT-16 4 Detected possible NULL Probe Response attack by [mac] [str]

Possible NULL probe response attack

ADV-WIPS ADV-WIPS-EVENT-105 4 Sanctioned MU [mac] detected associated with unsanctioned/neighboring AP [str]

Sanctioned MU detected associated with unsanctioned/neighboring AP

ADV-WIPS ADV-WIPS-EVENT-109 4 Multicast all systems traffic found from [mac] [str]

Multicast all systems traffic

ADV-WIPS ADV-WIPS-EVENT-110 4 Multicast all routers traffic found from [mac] [str]

Multicast all routers traffic

ADV-WIPS ADV-WIPS-EVENT-111 4 Multicast OSPF all traffic found from [mac] [str]

Multicast OSPF all traffic

ADV-WIPS ADV-WIPS-EVENT-112 4 Multicast OSPF Deisgnated Routers traffic found from [mac] [str]

Multicast OSPF designated routers traffic

ADV-WIPS ADV-WIPS-EVENT-113 4 Multicast RIP-2 Routers traffic found from [mac] [str]

Multicast RIP 2 routers traffic

ADV-WIPS ADV-WIPS-EVENT-114 4 Multicast IGRP Routers traffic found from [mac] [str]

Multicast IGRP routers traffic

ADV-WIPS ADV-WIPS-EVENT-115 4 Multicast DHCP Server Relay Agent traffic found from [mac] [str]

Multicast DHCP server relay agent traffic

ADV-WIPS ADV-WIPS-EVENT-116 4 Multicast VRRP Agent traffic found from [mac] [str]

Multicast VRRP agent traffic

ADV-WIPS ADV-WIPS-EVENT-117 4 Multicast HSRP Agent traffic found from [mac] [str]

Multicast HSRP agent traffic

ADV-WIPS ADV-WIPS-EVENT-118 4 Multicast IGMP traffic found from [mac] [str]

Multicast IGMP traffic

ADV-WIPS ADV-WIPS-EVENT-119 4 Detected NETBIOS traffic from [mac] [str]

Detected NETBIOS traffic

ADV-WIPS ADV-WIPS-EVENT-120 4 Detected STP traffic from [mac] [str]

Detected STP traffic

ADV-WIPS ADV-WIPS-EVENT-113 4 Multicast RIP-2 Routers traffic found from [mac] [str]

Multicast RIP 2 routers traffic

ADV-WIPS ADV-WIPS-EVENT-121 4 Detected IPX traffic from [mac] [str]

Detected IPX traffic

ADV-WIPS ADV-WIPS-EVENT-142 4 Detected possible Probe Response attack by [mac] [str]

Possible probe response attack

ADV-WIPS ADV-WIPS-EVENT-221 4 Detected Invalid Management Frames from [mac] [str]

Invalid management frames

ADV-WIPS ADV-WIPS-EVENT-26 4 Detected DoS RTS flood attack against [mac] [str]

DoS RTS flood attack

ADV-WIPS ADV-WIPS-EVENT-222 4 Detected Invalid Channel Advertisement for [mac] [str]

Invalid channel advertisement

ADV-WIPS ADV-WIPS-EVENT-63 4 Detected Windows ZERO Configuration Memory Leak on [mac] [str]

Windows ZERO configuration memory leak

ADV-WIPS ADV-WIPS-EVENT-220 4 Detected Unauthorized Bridge [mac] [str]

Unauthorized bridge

AP SW_CONN_LOST 0 Lost connectivity with controller after config update. Rebooting and reverting to older working configuration

Controller connectivity lost

AAA RADIUS_DISCON_MSG5 Received Radius dynamic authorization Disconnect Message for [qstr] from server [qstr]

Received RADIUS disconnect request

AAA RADIUS_VLAN_UPDATE6 Assigning Radius server specified vlan [uint] to client [qstr] on wlan [qstr]

Client VLAN updated by RADIUS resource

AAA RADIUS_SESSION_NOT_STARTED5 Radius server indicates session time has not started for client [qstr]

Start time from RADIUS resource not yet valid

AAA RADIUS_SESSION_EXPIRED5 Radius server indicates session has already expired for client [qstr]

Session time from RADIUS resource already expired

CAPTIVE-PORTAL AUTH_SUCCESS6 Captive-portal authentication success for client [mu] ([qstr-ip]) user [qstr]

Authentication sucess

ADV-WIPS ADV-WIPS-EVENT-26 4 Detected DoS RTS flood attack against [mac] [str]

DoS RTS flood attack

ADV-WIPS ADV-WIPS-EVENT-222 4 Detected Invalid Channel Advertisement for [mac] [str]

Invalid channel advertisement

ADV-WIPS ADV-WIPS-EVENT-63 4 Detected Windows ZERO Configuration Memory Leak on [mac] [str]

Windows ZERO configuration memory leak

ADV-WIPS ADV-WIPS-EVENT-220 4 Detected Unauthorized Bridge [mac] [str]

Unauthorized bridge

AP SW_CONN_LOST 0 Lost connectivity with controller after config update. Rebooting and reverting to older working configuration

Controller connectivity lost

AAA RADIUS_DISCON_MSG5 Received Radius dynamic authorization Disconnect Message for [qstr] from server [qstr]

Received RADIUS resource disconnect request

AAA RADIUS_VLAN_UPDATE6 Assigning Radius server specified vlan [uint] to client [qstr] on wlan [qstr]

Client VLAN updated by RADIUS

AAA RADIUS_SESSION_NOT_STARTED5 Radius server indicates session time has not started for client [qstr]

Start time from RADIUS resource not yet valid

AAA RADIUS_SESSION_EXPIRED5 Radius server indicates session has already expired for client [qstr]

Session time from RADIUS resource already expired

CAPTIVE-PORTAL AUTH_SUCCESS6 Captive-portal authentication success for client [mu] ([qstr-ip]) user [qstr]

Authentication success

CAPTIVE-PORTAL AUTH_FAILED6 Captive-portal authentication failed for client [mu] ([qstr-ip])

Authentication failed

CAPTIVE-PORTAL SESSION_TIMEOUT6 Captive-portal session timed out for client [mu] ([qstr-ip])

Session timed out

CAPTIVE-PORTAL CLIENT_DISCONNECT 6 Captive-portal session disconnected for client [mu] ([qstr-ip])

Client disconnected

CAPTIVE-PORTAL PURGE_CLIENT6 Captive-portal: Purge client [mu] by new client [mu] for user [qstr]

Client purged

CAPTIVE-PORTAL FLEX_LOG_ACCESS 6 [qstr]: [qstr] allowed access for client [mu] ([qstr-ip])

Flex log access granted for client

CAPTIVE-PORTAL INACTIVITY_TIMEOUT 6 Captive-portal session cleared for client [mu] ([qstr-ip]) after inactivity timeout

Client timed out due to inactivity

CAPTIVE-PORTAL ALLOW_ACCESS6 Captive-portal allow access for client [mu] ([qstr-ip])

Client allowed access

CAPTIVE-PORTAL CLIENT_REMOVED6 Captive-portal session removed for client [mu] ([qstr-ip]) on policy change/admin action

Client removed due to admin changes

CAPTIVE-PORTAL PAGE_CRE_FAILED3 Page creation failed for policy [qstr], file [qstr], Error [qstr]

Page creation failure

CAPTIVE-PORTAL DATA_LIMIT_EXCEED6 Data limit exceed, Usage:[int] KBytes, Action:[str], client [mu] ([ip])

Client data limit exceeded

CAPTIVE-PORTAL VLAN_SWITCH6 Client [mu] ([ip]) switching from vlan [int] to vlan [int]

Client VLAN switch

CAPTIVE-PORTAL SERVER_MONITOR_STATE_CHANGE6 Captive-portal policy [qstr]: service monitor [str] server status changing from [qstr] to [qstr]

Captive portal server monitor state changed

CAPTIVE-PORTAL NO_SERVICE_PAGE_SENT6 Captive-portal sent no service page to client [mu] ([ip]) as [str] server is down

No service page sent to client

CERTMGR RSA_KEY_ACTIONS_SUCCESS 6 [str] of RSA key [str] successful

Successful completion of RSA key related actions (import, export etc.)

CERTMGR RSA_KEY_ACTIONS_FAILURE 3 [str] of RSA key [str] failed: [str]

Failure of RSA key related actions (import, export etc.)

CERTMGR CA_CERT_ACTIONS_SUCCESS 6 [str] of CA certificate for trustpoint [str] successful

Successful completion of CA certificate related actions (import, export etc.)

CERTMGR CA_CERT_ACTIONS_FAILURE 3 [str] of CA certificate for trustpoint [str] failed: [str]

Failure of CA certificate actions (import, export etc.)

CERTMGR SRV_CERT_ACTIONS_SUCCESS 6 [str] of Server Certificate of trustpoint [str] successful

Successful completion of server certificate actions (import, export etc.)

CERTMGR SVR_CERT_ACTIONS_FAILURE 3 [str] of Server Certificate of trustpoint [str] failed: [str]

Failure of server certificate actions (import, export etc.)

CERTMGR CSR_EXPORT_SUCCESS 6 Export of Certificate Signing Request for [str] successful

Successful export of certificate signing request

CERTMGR CSR_EXPORT_FAILURE 3 Export of Certificate Signing Request for [str] failed: [str]

Failed to export certificate signing request

CERTMGR CRL_ACTIONS_SUCCESS 6 [str] of CRL for trustpoint [str] successful

Successful completion of certificate revocation list action

CERTMGR CRL_ACTIONS_FAILURE 3 [str] of CRL for trustpoint [str] failed: [str]

Certificate revocation list action failure

CERTMGR DELETE_TRUSTPOINT_ACTION 6 Deletion of trustpoint [str] successful

Deletion of trustpoint

CERTMGR IMPORT_TRUSTPOINT 6 Import of Trustpoint [str] [str]

Import of trustpoint

CERTMGR EXPORT_TRUSTPOINT 6 Export of Trustpoint [str] [str]//

Export of trustpoint

CERTMGR CERT_EXPIRY 4 [str] certificate for trustpoint [str] [str]

Certificate expiration

CERTMGR CA_KEY_ACTIONS_SUCCESS 6 [str] of CA private key for trustpoint [str] successful

Successful completion of CA private key actions

CERTMGR CA_KEY_ACTIONS_FAILURE 3 [str] of CA private key for trustpoint [str] failed: [str]

Failure of CA private key actions

CLUSTER CMASTER_CFG_UPDATE_FAIL 3 Cluster master config update to [str] failed, Err: [str]

Cluster master config update failed

CLUSTER MAX_EXCEEDED 4 Max cluster members ([uint]) exceeded, clustering will not function properly until corrected

Max cluster count exceeded

CLUSTER STATE_CHANGE 4 Active cluster member changed. Present active [str]. Previous active [str].

Active cluster membership change

CLUSTER STATE_CHANGE_INACTIVE 4 Member [str] (load[int]) changing state from Active to Standby. New member [str] standby load [int].

Cluster member change from active to standby

CLUSTER STATE_CHANGE_ACTIVE 4 Member [str] (load[int]) changing state from Standby to Active. New member [str] standby load [int]

Cluster member change from standby to active

CLUSTER STATE_RETAIN_ACTIVE 4 Member [str] (load[int]) retaining Active state. New member [str] standby load [int]

Cluster member retaining active state

CRM CRITICAL_RESOURCE_UP5 Critical Resource [str] is UP

Critical resource is up

CRM CRITICAL_RESOURCE_DOWN 5 Critical Resource [str] is DOWN

Critical resource is down

CERTMGR-LITE INVALIDCACERT 5 CA Certificate imported for the trustpoint [str] is invalid

CA certificate is invalid

CERTMGR-LITE INVALIDSERVCERT 5 Server Certificate imported for the trustpoint [str] is invalid

Server certificate is invalid

CERTMGR-LITE INVALIDCERTCRL 5 Certificate Crl Imported for trustpoint [str] is invalid

CRL is invalid

CERTMGR-LITE CERTEXPIRED 5 [str] Certificate of trustpoint [str] is expired//

Certificate is expired

CERTMGR-LITE INVALIDCERTKEY 5 Private key imported for trustpoint [str] is not valid

Private key is invalid

CERTMGR-LITE INVALIDRSAKEY 5 Rsakey imported is not valid [str] is invalid//

RSA key import operation

CERTMGR-LITE KEYDECRYPTFAILE 4 Rsakey cannot be decrypted with the password provided

RSA key cannot be decrypted with provided password

CERTMGR-LITE CERTIMPORTED 6 [str] Certificate imported for the trustpoint [str]

Certificate imported for trustpoint

CERTMGR-LITE CERTKEYIMPORTED 6 Private key imported for the trustpoint [str]

Private key imported for trustpoint

CERTMGR-LITE RSAKEYIMPORTED 6 Rsakey imported with the name [str]

RSA key imported

CERTMGR-LITE DELETETRUSTPOINT 6 Trustpoint [str] is deleted

Trustpoint deleted

CERTMGR-LITE DELETERSAKEY 6 Rsakey [str] is deleted

RSA Key deleted

CERTMGR-LITE CERTREQUESTGEN 6 Certificate request generated for the trustpoint [str]

Certificate requested generated

CERTMGR-LITE CERTSELFSIGNEDGEN 6 Selfsigned certificate generated for the trustpoint [str]

Self signed certificate generated

CERTMGR-LITE RSAKEYGEN 6 Rsa key [str] generated

RSA key generated

CERTMGR-LITE ERROR 5 [str]

Certificate manager general error

CERTMGR-LITE CERT_EXPIRY4 [str] certificate for trustpoint [str] [str]

Certificate about to expire

CERTMGR CERT_RENEW_FAILED1 Certificate renew in field failed reason [str]

Certificate renew failure reason

DHCPSVR DHCPSVR_STOP 6 DHCP server is stopped

DHCP server stopped

DIAG WD_RESET_SYS 2 The system has been RESET by the Watchdog

Log watchdog reset

DIAG CPU_USAGE_TOO_HIGH 4 CPU Usage too high. Limit of [int]*(0.1%) exceeded. Current CPU usage is [int]*(0.1%)

Log CPU load detected as too high

DIAG CPU_USAGE_TOO_HIGH_RECOVER 4 CPU Usage too high recover. Limit is [int]*(0.1%)

Current CPU usage is too high

DIAG CPU_LOAD 4 [str] minute average load limit exceeded, value is [str]% limit is [str]% (top processes: [str])

CPU average load limit exceeded

DIAG RAM_USAGE 6 [str], pid [uint], has exceeded ram usage limit [uint].[uint]%, now using [uint].[uint]%

Log processor RAM usage has exceeded RAM limit

DIAG MEM_USAGE_TOO_HIGH 6 Memory Usage too high. Current Usage is [int]*(0.1%). Memory Usage Threshold is [int]*(0.1%)

Memory usage too high

DIAG MEM_USAGE_TOO_HIGH_RECOVER 6 Memory Usage too high recover. Current Usage is [int]*(0.1%). Memory Usage Threshold is [int]*(0.1%)

Memory usage detected as too high

DIAG BUF_USAGE 6 [uint] byte buffer usage greater than expected, [uint] used, warning level [uint]

Log buffer usage greater than anticipated

DIAG HEAD_CACHE_USAGE 6 socket buffer head cache usage is greater than expected, usage [uint], warning level [uint]

Log head cache usage greater than anticipated

DIAG IP_DEST_USAGE 6 IP destination cache usage is greater than expected, usage [uint], warning level [uint]

Log destination cache usage greater than anticipated

DIAG FREE_RAM 6 Free RAM, [str]% is less than limit [str]%. Top Memory process: [str]/[uint] using [uint].[uint]% , [str]/[uint] using [uint].[uint]% , [str]/[uint] using [uint].[uint]%

Log RAM space less than limit

DIAG FREE_FLASH_DISK 4 Free [str] file system space, [str]% is less than limit [str]%

Log free disk space less than limit

DIAG DISK_USAGE 4 Disk usage too high

Log disk usage too high

"DIAG NEW_LED_STATE 6 LED state message [str] from module [str]

Log LED message from module

DIAG FREE_FLASH_INODES 4 [uint] Free INodes on [str] file system is less than limit [uint]

Log INodes less than system limit

DIAG FREE_NVRAM_DISK 4 Free [str] file system space, [str]% is less than limit [str]%

Log file system space less than limit

DIAG FREE_NVRAM_INODES 4 [uint] Free INodes on [str] file system is less than limit [uint]

Log free INodes on file system less than limit

DIAG FREE_RAM_DISK 4 Free [str] file system space, [str]% is less than limit [str]%

Log free file system space less than limit

DIAG FREE_RAM_INODES 4 [uint] Free INodes on [str] file system is less than limit [uint]

LOG_FREE_VARFS_INODES

DIAG FD_COUNT 4 FD Usage [uint] is over limit [uint]

HUMM

DIAG DISK_USAGE 4 Disk usage too high

Log disk utilization usage too high

DIAG NEW_LED_STATE 6 LED state message [str] from module [str]

Log LED state message from module

DIAG LED_IDENTIFY 6 LED identify sequence [str]

Log identification sequence

"DHCPSVR RELAY_NO_IFACE 4 Dhcp relay cannot be allowed on interface [str] as it does not exist

No interface for DHCP relay

DHCPSVR RELAY_IFACE_NO_IP 4 Dhcp relay cannot be allowed on interface [str] as it does not have an IP address

No IP address on DHCP relay interface

DHCPSVR RELAY_START 6 DHCP relay agent started on [str]

DHCP relay agent started

DHCPSVR RELAY_STOP 6 DHCP relay agent stopped

DHCP relay agent stopped

DHCPSVR DHCPSVR_START 6 DHCP server is started

DHCP server started

DIAG FAN_UNDERSPEED 4 Fan [str] under speed: [uint] RPM is under limit [uint] RPM

Fan speed under set RPM limit

DIAG ELAPSED_TIME 7 Elapsed time since last diag run appears to be zero

Log elapsed time since last diagnostic run

DIAG AUTOGEN_TECH_SPRT 6 Auto generated tech-support dump file [str] [str]

Log generation of tech support dump file

DIAG POE_INIT_FAIL 3 Could not initialize the PoE manager

Log PoE manager intialization failure

DIAG POE_POWER_LEVEL 4 POE power consumption is [uint]W which exceeds [uint]% of [uint]W power budget

Log power consumption exceeds power budget limit

DIAG POE_READ_FAIL 3 Could not read from the PoE

Log PoE read failure

DIAG POE_STATE_CHANGE 4 port [uint] POE state changed to [str]

Log PoE state change

DIAG RAID_DEGRADED 4 RAID array is degraded

Log RAID array degraded

DIAG RAID_ERROR 4 RAID array management error [uint]

Log RAID array management error

DIAG PWRSPLY_FAIL 4 Power supply failure, no longer redundant

Log power supply failure

DIAG HDD_FAILING 4 HDD is failing

Log HDD failure

DIAG UNDER_VOLTAGE 4 Voltage [str]V under low limit [str]V

Log voltage sensor under low limit

DIAG OVER_VOLTAGE 4 Voltage [str]V over high limit [str]V

Log voltage sensor over high limit

DIAG LOW_TEMP 6 Temp sensor [str] [str]C under low limit [str]C

Log temperature sensor under low limit

DIAG HIGH_TEMP 4 Temp sensor [str] [str]C over high limit [str]C

Log temperature sensor over high limit

DIAG OVER_TEMP 0 Temp sensor [str] [str]C over maximum limit [str]C Shutdown switch

Log temperature sensor over max limit

DIAG WD_STATE_CHANGE 6 Watchdog is now [str]

Log watchdog state

DOT1X DOT1X_SUCCESS 6 Client [qstr] 802.1x/EAP authentication success on interface [qstr]//802.1x authentication successful

802.1X authentication successful

DOT1X DOT1X_FAILED 5 Client [qstr] failed 802.1x/EAP authentication on interface [qstr]//802.1x authentication failure

802.1X authentication failed

DOT11 COUNTRY_CODE 5 Country of operation configured to [str]

Country of operation configured

DOT11 COUNTRY_CODE_ERROR 1 Error setting country of operation. [str]

Error setting country of operation

DOT11 CLIENT_ASSOCIATED 6 Client [qstr] associated to wlan [qstr] ssid [qstr] on radio [qstr]

Client associated event

DOT11 CLIENT_DISASSOCIATED 6 Client [qstr] disassociated from wlan [qstr] radio [qstr]: [str] (reason code:[uint])

Client disassociated

DOT11 CLIENT_DENIED_ASSOC 5 Client [qstr] denied association on radio [qstr] [str]: [str]

Client denied association

DOT11 CLIENT_ASSOC_IGNORED 6 Client [qstr] ignored association on radio [qstr] [str]: [str]

Client ignored association

DOT11 WPA_WPA2_SUCCESS 6 Client [qstr] completed [str] handshake on wlan [qstr] radio [qstr]

Client completed WPA/WPA2 handshake

DOT11 WPA_WPA2_FAILED 5 Client [qstr] failed [str] handshake on wlan [qstr] radio [qstr]

Client failed WPA/WPA2 handshake

DOT11 WPA_WPA2_KEY_ROTN 6 Rotating wpa/wpa2 group keys on wlan [qstr] /

Rotating WPA/WPA2 group keys on WLAN

DOT11 TKIP_MIC_FAIL_REPORT 5 TKIP message integrity check failure reported by [mac] on wlan [qstr]

TKIP MIC failure report

DOT11 TKIP_MIC_FAILURE 5 TKIP message integrity check failed in packet from [mac] on wlan [qstr]

TKIP MIC check failed

DOT11 TKIP_CNTRMEAS_START 4 Initiating TKIP countermeasures on wlan [qstr] ssid [qstr]

TKIP countermeasures initiated

DOT11 TKIP_CNTRMEAS_END 4 TKIP countermeasures ended on wlan [qstr] ssid [qstr] //

TKIP countermeasures ended

DOT11 EAP_SUCCESS 6 Client [qstr] 802.1x/EAP (type:[str]) authentication success on wlan [qstr] radio [qstr] username [str]

EAP authentication success

DOT11 EAP_FAILED 5 Client [qstr] failed 802.1x/EAP authentication on wlan [qstr] radio [qstr]

EAP authentication failure

DOT11 EAP_CLIENT_TIMEOUT 5 Client [qstr] timeout attempting 802.1x/EAP authentication on wlan [qstr] radio [qstr]

EAP authentication timed out

DOT11 EAP_SERVER_TIMEOUT 5 Radius server [str] timeout authenticating client [qstr] on wlan [qstr] radio [qstr]

RADIUS server timed out

DOT11 EAP_CACHED_KEYS 6 Key Cache used for client [qstr] on wlan [qstr] radio [qstr]. Skipping 802.1x

Key cache used for authentication

DOT11 EAP_OPP_CACHED_KEYS 6 Opportunistic Key Cache used for client [qstr] on wlan [qstr] radio [qstr]. Skipping 802.1x.

Opportunistic key caching used for authentication

DOT11 EAP_PREAUTH_SUCCESS 6 Client [qstr] 802.1x/EAP (type:[str]) pre-authentication success on wlan [qstr] bss [mac]

EAP pre authentication success

DOT11 EAP_PREAUTH_FAILED 5 Client [qstr] failed 802.1x/EAP pre-authentication on wlan [qstr] bss [mac]

EAP pre-authentication failed

DOT11 EAP_PREAUTH_CLIENT_TIMEOUT 5 Client [qstr] timeout attempting 802.1x/EAP pre-authentication on wlan [qstr]

EAP pre-authentication client timeout detected

DOT11 EAP_PREAUTH_SERVER_TIMEOUT 5 Radius server [qstr] timeout pre-authenticating client [qstr] on wlan [qstr]

EAP pre-authentication server timeout detected

DOT11 FT_ROAM_SUCCESS 6 Client [qstr] fast bss transition roam to wlan [qstr] ssid [qstr] on radio [qstr]

Client fast BSS transition roam to WLAN SSD ID on radio

DOT11 GAL_RX_REQUEST 6 Received request to validate [qstr] on global assoc-list [qstr] from [qstr] on rf-domain [qstr]

Received request to validate global association request for RF Domain

DOT11 GAL_TX_RESPONSE 6 Sending global assoc-list [qstr] response for [qstr] to [qstr] on rf-domain [qstr], result: [str]

Sending global association response for RF Domain

DOT11 GAL_VALIDATE_REQ 6 Sending global assoc-list validation request to controller for [qstr]

Sending global association list validation to controller

DOT11 GAL_VALIDATE_FAILED 6 Received global assoc-list validation failure for [qstr]

Received global association list validation failures

DOT11 GAL_VALIDATE_SUCCESS 6 Received global assoc-list validation success for [qstr]

Received global association list validation successes

FWU FWUDONE 6 Firmware update successful, new version is [str]

Update successfully completed

FWU FWUABORTED 6 Firmware update aborted

Update aborted

FWU FWUNONEED 6 Firmware update not required, running and update versions same [str]

Update not required, running and update version are the same

FWU FWUSYSERR 3 Firmware update unsuccessful, system cmd [str] failed

Update unsuccessful, system cmd failed

FWU FWUBADCONFIG 3 Firmware update unsuccessful, unable to read configuration file

Update unsuccessful, unable to read config file

FWU FWUSERVERUNDEF 3 Firmware update unsuccessful, update server undefined

Update unsuccessful, server undefined

FWU FWUFILEUNDEF 3 Firmware update unsuccessful, update file undefined

Update unsuccessful, update file undefined

FWU FWUSERVERUNREACHABLE 3 Firmware update unsuccessful, server [str] unreachable

Update unsuccessful, server unreachable

FWU FWUCOULDNTGETFILE 3 Firmware update unsuccessful, couldn't get file, [str] //

Update unsuccessful, could not get file

FWU FWUVERMISMATCH 3 Firmware update unsuccessful, version mismatch, expected [str], actual [str] //

Update unsuccessful, version mismatch

FWU FWUPRODMISMATCH 3 Firmware update unsuccessful, product mismatch, expected [str], actual [str]

Update unsuccessful, product mismatch

FWU FWUCORRUPTEDFILE 3 Firmware update unsuccessful, corrupted firmware file

Update unsuccessful, corrupted file

FWU FWUSIGNMISMATCH 3 Firmware update unsuccessful, signature mismatch, [str]

Update unsuccessful, signature mismatch

FWU FWUUNSUPPORTEDHW 3 Firmware update unsuccessful, unsupported hardware

Update unsuccessful, unsupported hardware version

FWU FWUUNSUPPORTEDMODELNUM 3 Firmware update unsuccessful, unsupported FIPS model number

Update unsuccessful, unsupported FIPS model number

ISDN_EMERG 0 Emergency: [str]

ISDN emergency

ISDN_ALERT 1 Alert: [str]

ISDN alert

ISDN_CRIT 2 Critical: [str]

ISDN critical

ISDN_ERR 3 Error: [str]

ISDN error

ISDN_WARNING 4 Warning: [str]

ISDN warning

ISDN_NOTICE 5 Notice: [str]

ISDN notice

ISDN_INFO 6 Info: [str]

ISDN information

ISDN_DEBUG 7 Debug: [str]

ISDN debug

L2TPV3 L2TPV3_TUNNEL_UP 5 L2TPV3 tunnel [str] is UP

L2TPV3 tunnel is up

L2TPV3 L2TPV3_TUNNEL_DOWN 5 L2TPV3 tunnel [str] is DOWN

L2TPV3 tunnel is down

LICMGR LIC_INSTALLED 6 [str] license installed

License installation

LICMGR LIC_INSTALL_DEFAULT 6 [str] default license installed, count: [int]

Default license installation

LICMGR LIC_INSTALL_COUNT 6 [str] license installed, count: [int]

License count

LICMGR LIC_REMOVED 6 [str] license removed

License removed

LICMGR LIC_INVALID 3 [str] license invalid Error: [str]

License installation failed

MESH MESH_LINK_UP 5 Mesh link up between radio [qstr] and radio [qstr]

Mesh link up

MESH MESH_LINK_DOWN 5 Mesh link down between radio [qstr] and radio [qstr]

Mesh link down

MGMT LOG_KEY_DELETED 4 Rsakey [str] associated with ssh is deleted so ssh is restarted with default rsa key

RSA key associated with SSH is deleted

MGMT LOG_KEY_RESTORED 6Rsakey [str] associated with ssh is added so ssh is restarted with new key

RSA key associated with SSH is added

MGMT LOG_TRUSTPOINT_DELETED 4 Trustpoint [str] associated with https is deleted or expired so https is restarted with default trustpoint

Trustpoint associated with HTTPS is deleted

MGMT LOG_HTTP_START 5 [str] started in external mode

Web server started in external mode

MGMT LOG_HTTP_LOCAL_START 5 thttpd started in localhost mode

Web server started in local mode

MGMT LOG_HTTPS_START 5 stunnel started

Secure Web server started

MGMT LOG_HTTPS_WAIT 5 waiting for thttpd to start

Waiting for Web server to start

MGMT LOG_HTTP_INIT 5 [str] status started is [uint] and external mode is [uint]

Web server started

MESH MESHPOINT_LOOP_PREVENT_ON 4 Meshpoint [qstr] loop prevention on (port [str]), wired traffic is blocked

Wired traffic is blocked

MESH MESHPOINT_LOOP_PREVENT_OFF 4 Meshpoint loop prevention off (port [str]), all wired traffic is allowed

Wired traffic is allowed

MESH MESHPOINT_ROOT_CHANGE 6 Meshpoint [qstr] root changed from [mac] to [mac] via next hop [mac]

Meshpoint root changed

MESH MESHPOINT_PATH_CHANGE 6 Meshpoint [qstr] next hop changed from [mac] to [mac] for [mac]

Meshpoint next hop changed

NSM IFUP 4 Interface [str] is up

Interface up

NSM IFDOWN 4 Interface [str] is down

Interface down

NSM DHCPIP 6 Interface [str] acquired IP address [ip]/[uint] via DHC

Interface assigned DHCP IP address

NSM DHCPDEFRT 6 Default route with gateway [ip] learnt via DHC

Default route learnt via DHCP

NSM DHCPIPCHG 5 Interface [str] changed DHCP IP - old IP: [ip]/[uint], new IP: [ip]/[uint]

DHCP Interface IP changed

NSM DHCPNODEFRT 5 Interface [str] lost its DHCP default route

Interface no default route

NSM IFIPCFG 3 Interface [str] IP address [str] Interface [str]

Interface IP address

NSM DHCPC_ERR 3 Both, DHCP client and server are configured for interface [str]. DHCP Client has been enabled on the interface and dhcp server is shut down

DHCP server-client config conflict

NSM DHCPIPNOADD 5 Interface [str] lost its DHCP IP address to interface [str]'s overlapping static configured IP address

DHCP IP overlaps static IP address

NSM DHCPLSEXP 5 Interface [str] lost its DHCP IP address [ip] due to lease expiration

Interace DHCP lease expired

NSM DHCPNAK 5 Interface [str] lost its DHCP IP address [ip], DHCP NAK response from server

DHCP Server returned DHCP NAK response

NSM NSM_NTP 6 Look up host [str] [str]//

Translate host name

NSM IF_FAILOVER 5 Interface [str] failover to Interface [str]

Interface failover

NSM IF_FAILBACK 5 Interface [str] failback to Interface [str]

Interface failback

PM PROCSTART 6 Starting process [str]

Process started

PM PROCRSTRT 3 Process str]"is not responding. Restarting process

Process restarted

PM PROCMAXRSTRT 1 Process [str] reached its maximum number of allowed restarts

Process reached max number of restarts

PM PROCSYSRSTRT 0 Process [str] reached its maximum number of allowed restarts. Rebooting the system.

Process reached max restarts. Rebooting system.

PM PROCSTOP 5 Process [str] has been stopped

Process has been stopped

PM PROCID 5 Process [str] changed its PID from [int] to [int]

Process changed PID

PM STARTUPCOMPLETE 5 System startup complete

System startup completed

PM PROCNORESP 4 Process [str] is not responding ([uint]/[uint])

Process is not responding

RADCONF RADIUSDSTART 6 Radius Server Started

RADIUS server started

RADCONF RADIUSDSTOP 6 Radius Server Stopped

RADIUS server stopped

RADCONF COULD_NOT_STOP_RADIUSD 3 radiusd could not be stopped

RADIUS server failed to stop

RADIO RADIO_STATE_CHANGE 5 Radio [qstr] changing state from [qstr] to [qstr]

Radio state changed

RADIO RADAR_SCAN_STARTED 6 Radar scan on primary channel [uint] freq [uint] MHz for a duration [uint] secs on radio [qstr]

Radar scan started

RADIO RADAR_SCAN_COMPLETED 6 Radar scan done on primary channel [uint] freq [uint] MHz on radio [qstr]

Radar scan completed

RADIO RADAR_DETECTED 4 Radar found on channel [uint] freq [uint] MHz

Radar detected

RADIO RADAR_DET_INFO 4 Radar info: Radio: [qstr]. New channel: [uint] freq [uint] MHz. Scan time: [uint] secs

Radar info

RADIO RESUME_HOME_CHANNEL 6 Operation on home channel [uint] freq [uint] MHz resumes on radio [qstr] after earlier radar detect

Radio resuming on home channel

RADIO ACS_SCAN_STARTED 6 ACS scan started on radio [qstr]

ACS scan started

RADIO ACS_SCAN_COMPLETE 6 ACS scan done, channel [uint] selected on radio [qstr]

ACS scan complete

RADIO_ANTENNA_ERROR 3 antenna type [str] in is not supported on radio [uint] of device [str]

Invalid (unsupported) antenna detected on this radio

RADIO CHANNEL_COUNTRY_MISMATCH 3 Channel [str] not valid in country of operation [str] for [str] [str]

Channel and country of operation mismatch

SYSTEM HTTP_ERR 3 [str] did not start

Web server did not start

SYSTEM LOGIN_FAIL_BAD_ROLE 3 Log-in failed - [qstr] is an undefined user role - user [qstr] from [qstr]

Failed login attempt - no such user role

SYSTEM LOGOUT 6 Logged out user [qstr] with privilege [qstr] from [qstr]

Logout event

SYSTEM WARM_START 6 System Warm Start Reason : [str] Timestamp: [str]

System warm start

SYSTEM WARM_START_RECOVER 6 Warm Start Recover. Reason: [str] Timestamp: [str]

System wam start recovery

SYSTEM COLD_START 6 System Cold start. System came up at [str]

System cold start

SYSTEM SERVER_UNREACHABLE 5 Server not reachable, trying authentication using local database .

Authentication using the local database

SYSTEM PERIODIC_HEART_BEAT 3 Periodic Heart Beat. Interval:[int]. Ip address [str].

Periodic heartbeat detected

SYSTEM CONFIG_COMMIT 6 Configuration commit by user [qstr] ([str]) from [qstr]

Configuration commit

SYSTEM CONFIG_REVISION 6 Configuration revision updated to [str] from [str]

Configuration updated

SYSTEM SYSTEM_AUTOUP_ENABLE 6 Autoupgrade enabled for [str]

Auto upgrade module is enabled

SYSTEM SYSTEM_AUTOUP_DISABLE 6 Autoupgrade disabled for [str]

Auto upgrade module is disabled

SYSTEM MAAT_LIGHT 5 MAAT Light module [str]

Notice on action on RIM radio(s) from Maat Light module

SYSTEM DEVUP_RFD_FAIL 4 Upgrade failed on mac [str] in RF domain [str]

Upgrade for device failed on rf-domain manager

SMTPNOT SMTPAUTH 5 Authentication failure for user: [str] on server [str].//

User authentication failure

SMTPNOT NET 5 Network error contacting server: [str].

Cannot contact server

SMTPNOT SMTPINFO 6 [str].

SMTP information notice

SMTPNOT CFG 5 Error reading configuration file.

Cannot read configuration

SMTPNOT CFGINC 5 Incomplete Configuration.

Incomplete configuration

SMTPNOT SMTPERR 5 [str].

SMTP 5XX errors

SMTPNOT PROTO 5 Protocol Error: [str].

SMTP protocol errors

SYSTEM PROC_STOP 6 Stopping process [qstr]

Stopping process

SYSTEM CLOCK_RESET 6 System clock reset, Time: [str]

System clock reset

SYSTEM LOGIN 5 Successfully logged in user [qstr] with privilege [qstr] from [qstr]

Successful login

SYSTEM LOGIN_FAIL 3 Log-in failed for user [qstr] from [qstr]

Failed login attempt - user authentication failed

SYSTEM LOGIN_FAIL_ACCESS 3 Log-in failed - user [qstr] is not allowed access from [qstr]

Failed login attempt - access violation

VRRP VRRP_STATE_CHANGE 5 [str]: VRRP Group [uint] transitioned to [str] state

VRRP state transition

VRRP VRRP_VIP_SUBNET_MISMATCH 2 VRRP Group [uint] VIP [ip] does not overlap with any of the interface addresses

VRRP IP not overlapping with interface addresses

VRRP VRRP_MONITOR_CHANGE 5 [str]: VRRP Group [uint] monitored [str] state change to [str]; priority change from [uint] to [uint]

VRRP monitor link state change

WIPS UNSANCTIONED_AP_ACTIVE 6 Unsanctioned AP [mac] vendor [str] on channel [int] with rssi [int] active from [str]

Unsanctioned AP active

WIPS UNSANCTIONED_AP_INACTIVE 6 Unsanctioned AP [mac] vendor [str] inactive from [str]

Unsanctioned AP inactive

WIPS UNSANCTIONED_AP_STATUS_CHANGE 6 Unsanctioned AP [mac] vendor [str] status has been administratively changed

Unsanctioned AP changed state

WIPS ROGUE_AP_ACTIVE 4 Rogue AP [mac] vendor [str] on channel [int] with vlan [int] and rssi [int] active from [str] //

Rogue AP active

WIPS ROGUE_AP_INACTIVE 4 Rogue AP [mac] vendor [str] inactive from [str]

Rogue AP inactive

WIPS AIR_TERMINATION_INITIATED 4 Air termination of [mac] vendor [str] on channel [int] initiated

Air termination initiated

WIPS AIR_TERMINATION_ENDED 4 Air termination of [mac] vendor [str] ended

Air termination ended