Network Load Balancing

Table 1. Network Load Balancing product support

Feature

Product

Release introduced

Network Load Balancing (NLB) - multicast operation

5320 Series

Not Supported

5420 Series

Not Supported

5520 Series

VOSS 8.2.5

5720 Series

Fabric Engine 8.7

VSP 4450 Series

Not Supported

VSP 4900 Series

VOSS 8.1

VSP 7200 Series

VOSS 6.0

VSP 7400 Series

VOSS 8.0

VSP 8200 Series

VOSS 6.0

VSP 8400 Series

VOSS 6.0

VSP 8600 Series

Not Supported

XA1400 Series

Not Supported

Network Load Balancing (NLB) - unicast operation

5320 Series

Not Supported

5420 Series

Not Supported

5520 Series

VOSS 8.2.5

5720 Series

Fabric Engine 8.7

VSP 4450 Series

Not Supported

VSP 4900 Series

VOSS 8.1

VSP 7200 Series

VOSS 4.2.1

VSP 7400 Series

VOSS 8.0

VSP 8200 Series

VOSS 4.0

VSP 8400 Series

VOSS 4.2

VSP 8600 Series

VSP 8600 4.5

XA1400 Series

Not Supported

Microsoft Network Load Balancing (NLB) is a clustering technology available with the Microsoft Windows 2000, Microsoft Windows 2003, Microsoft Windows 2008, and Microsoft Windows 2012 Server family of operating systems. You can use NLB to share the workload among multiple clustering servers. NLB uses a distributed algorithm to load balance TCP/IP network traffic across a number of hosts, enhancing the scalability and availability of the following mission critical, IP-based services:

NLB also provides high availability by detecting host failures and automatically redistributing traffic to remaining operational hosts.

NLB Considerations and Restrictions

Although the switch interoperates with NLB clusters that operate in Unicast mode and Multicast mode, the following restrictions apply:

NLB Clustering in Unicast Mode

When the cluster is running in NLB unicast mode, all servers in the cluster share a common virtual MAC address, which is 02-bf-x-x-x-x (where x-x-x-x is the cluster IP address in hexadecimal form). All traffic destined to this MAC address is sent to all the servers in the cluster. The virtual MAC address is specified in the Sender MAC Address field of the Address Resolution Protocol (ARP) reply from the cluster to the switch. ARP responses from the switch are sent to the virtual MAC address (rather than to the hardware MAC address).

You can configure the switch for NLB unicast mode support. After you enable the NLB unicast option, the switch floods traffic destined to the cluster IP address to all ports on the VLAN. Unicast mode supports connectivity to a secondary virtual IP address. For information about software scaling capabilities in unicast mode, see VOSS Release Notes.

NLB Clustering in Multicast Mode

When the cluster is running in NLB multicast mode, a multicast virtual MAC address with the format 03-bf-x-x-x-x (where x-x-x-x is the cluster IP address in hexadecimal form) is bound to all cluster hosts but the real MAC address of the network adapter is retained. The multicast MAC address is used for client-to-cluster traffic, and the real MAC address of the adapter is used for network traffic specific to the host server.

You can configure the switch for NLB multicast mode support. When you enable NLB multicast mode on a VLAN, the routed traffic destined to the NLB cluster is flooded by default on all ports of the VLAN. All VLANs support multiple cluster IPs by default. You can connect up to 200 NLB clusters to a single VLAN. For information about software scaling capabilities, see VOSS Release Notes.

Note

Note

Shortest Path Bridging MAC (SPBM) supports NLB Unicast and Multicast modes. For more information on SPBM, see Fabric Basics and Layer 2 Services.