Displays complete or filtered information for all RSVP-TE LSPs.
| destination | Displays only those LSPs that terminate at the specified IP address. |
| origin | Displays only those LSPs that originate at the specified IP address. |
| ipaddress | Specifies an IP address for an LSP origin or destination. |
| fast-reroute | Limits the display to only those LSPs with fast reroute protection. |
| detail | Displays the LSP information in verbose format. |
| summary | Displays only the LSP summary statistics section of the normal display. |
N/A.
If no options are specified, information for all RSVP-TE LSPs is displayed.
You can limit the display to ingress, transit, or egress LSPs with the following commands:
show mpls rsvp-te lsp [ingress {fast-reroute} | ingress_lsp_name | ingressingress_lsp_name | ingress [destination | origin]ipaddress] {[all-paths | detail] | summary | down-paths {detail}} show mpls rsvp-te lsp [egress | transit] {fast-reroute} {{lsp_name} {[destination | origin] ipaddress} {detail} | summary}When label recording is enabled for an LSP, labels are displayed only for the ingress node (the egress label from the previous node always matches the ingress node label).
The following command example displays information about all RSVP-TE LSPs:
# show mpls rsvp-te lsp Ingress LSP Name Path Name Destination Next Hop I/F UpTm Flags ---------------- ---------------- --------------- ---------------- ---- -------- frrlsp1tom2 any 11.100.100.50 m2vlan1 5m UEF---IV lsptom2 pathtom2 11.100.100.50 m2vlan1 5m UES--OIV tom5 any 11.100.100.55 m5vlan1 5m UEP---IV Egress LSP Name Source IP Destination Prev Hop I/F UpTm ---------------- --------------- --------------- ---------------- ---- tom3 11.100.100.55 11.100.100.30 m5vlan1 5m frrlsp1tom3 11.100.100.50 11.100.100.30 m2vlan1 5m tom3 11.100.100.50 11.100.100.30 m2vlan1 5m Transit LSP Name Source IP Destination Prev Hop I/F Next Hop I/F UpTm ---------------- --------------- --------------- ------------- ------------- ---- tom2 11.100.100.55 11.100.100.50 m5vlan1 m2vlan1 5m frrlsp1tom5 11.100.100.50 11.100.100.55 m2vlan1 m5vlan1 5m lsptom5 11.100.100.50 11.100.100.55 m2vlan1 m5vlan1 5m Flags: (U) Up, (E) Enabled, (P) Primary LSP, (S) Secondary LSP, (F) FRR Primary LSP (R) Redundant Paths, (B) Bandwidth Requested, (O) ERO Specified, (I) IP Traffic Allowed, (V) VPN Traffic Allowed, (v) VPN Assigned Traffic Allowed Summary of RSVP-TE LSPs Ingress LSPs (Enabled/Disabled) : 3 (3/0) Ingress LSPs with no configured path : 0 Ingress LSP Paths (Up/Down) : 3 (3/0) Detour LSP Paths (Up/Down) : 0 (0/0) Transit LSPs : 3 Egress LSPs : 3
The next command example displays only the summary information for all RSVP-TE LSPs:
# show mpls rsvp-te lsp summary Summary of RSVP-TE LSPs Ingress LSPs (Enabled/Disabled) : 3 (3/0) Ingress LSPs with no configured path : 0 Ingress LSP Paths (Up/Down) : 3 (3/0) Detour LSP Paths (Up/Down) : 0 (0/0) Transit LSPs : 3 Egress LSPs : 3
The following command example limits the display to RSVP-TE LSPs with fast reroute protection:
# show mpls rsvp-te lsp fast-reroute Ingress LSP Name Path Name Destination Next Hop I/F UpTm Flags ---------------- ---------------- --------------- ---------------- ---- -------- frrlsp1tom2 any 11.100.100.50 m2vlan1 5m UEF---IV Egress LSP Name Source IP Destination Prev Hop I/F UpTm ---------------- --------------- --------------- ---------------- ---- tom3 11.100.100.55 11.100.100.30 m5vlan1 5m frrlsp1tom3 11.100.100.50 11.100.100.30 m2vlan1 5m tom3 11.100.100.50 11.100.100.30 m2vlan1 5m Transit LSP Name Source IP Destination Prev Hop I/F Next Hop I/F UpTm ---------------- --------------- --------------- ------------- ------------- ---- tom2 11.100.100.55 11.100.100.50 m5vlan1 m2vlan1 5m frrlsp1tom5 11.100.100.50 11.100.100.55 m2vlan1 m5vlan1 5m lsptom5 11.100.100.50 11.100.100.55 m2vlan1 m5vlan1 5m Flags: (U) Up, (E) Enabled, (P) Primary LSP, (S) Secondary LSP, (F) FRR Primary LSP (R) Redundant Paths, (B) Bandwidth Requested, (O) ERO Specified, (I) IP Traffic Allowed, (V) VPN Traffic Allowed, (v) VPN Assigned Traffic Allowed Summary of RSVP-TE LSPs Ingress FRR LSPs (Enabled/Disabled) : 1 (1/0) Ingress FRR LSPs with no configured path : 0 Ingress FRR LSP Paths (Up/Down) : 1 (1/0) Detour LSP Paths (Up/Down) : 0 (0/0) Transit FRR LSPs : 3 Egress FRR LSPs : 3
The following command example displays detailed information for all RSVP-TE LSPs:
Print
this page
Email this topic
Feedback
View PDF
Download EPUB
# show mpls rs lsp det
Ingress LSP Name: lsp_to_baha
Destination : 11.100.100.4 Admin Status : Enabled
IP Traffic : Allow #VPLS Cfgd : 0
VPN Traffic : Allow #VPLS In-Use : 0
Path Name: path1
Oper Status : Enabled UpTime : 0d:0h:4m:49s
Profile Name : default
Peak Rate : 0 Kbps Max Burst Size : 0 Kb
Committed Rate : 0 Kbps Setup/Hold Priority : 7/0
Record Route : Enabled
MTU : Use Local I/F
Tunnel ID : 1 Ext Tunnel ID : 11.100.100.1
LSP ID : 0 State Changes : 1
LSP Type : Primary Bandwidth Cfgd : False
Activity : Active
Failures : 0 Retries-since last failure : 0
Retries-Total : 0
Configured ERO : Order IP Address/Mask Type Inc/Exc
100 9.50.1.2/32 strict include
Advertised Label: n/a Received Label : 0x00434
Rx Packets : n/a Tx Packets : --
Rx Bytes : n/a Tx Bytes : --
Next Hop I/F : 9.50.1.1 - j1-j2vlan1
Next Hop Addr : 9.50.1.2
Record Route : Indx IP Address Label
: 1 9.50.1.2 0x00434
: 2 9.54.1.4 0x00434
Path Name: path2
Oper Status : Enabled UpTime : 0d:0h:4m:49s
Profile Name : default
Peak Rate : 0 Kbps Max Burst Size : 0 Kb
Committed Rate : 0 Kbps Setup/Hold Priority : 7/0
Record Route : Enabled
MTU : Use Local I/F
Tunnel ID : 2 Ext Tunnel ID : 11.100.100.1
LSP ID : 0 State Changes : 1
LSP Type : Secondary Bandwidth Cfgd : False
Activity : Standby
Failures : 0 Retries-since last failure : 0
Retries-Total : 0
Configured ERO : Order IP Address/Mask Type Inc/Exc
100 9.50.1.2/32 n/a exclude
Advertised Label: n/a Received Label : 0x00435
Rx Packets : n/a Tx Packets : --
Rx Bytes : n/a Tx Bytes : --
Next Hop I/F : 9.52.1.1 - j1-j4vlan1
Next Hop Addr : 9.52.1.4
Record Route : Indx IP Address Label
: 1 9.52.1.4 0x00435
This command was first available in ExtremeXOS 11.6.
This command and its output were modified, and the summary option was added in ExtremeXOS 12.0.
The fast-reroute feature was first available in ExtremeXOS 12.1.
This command and its output were modified in ExtremeXOS 12.2.2.
The output was modified to include the include/exclude information in ExtremeXOS 15.7.1.
This command is available only on the platforms that support MPLS as described in the Feature License Requirements document.