Displays the specified TDM port information.
|
tdm |
Time Division Multiplexing. |
|
information |
Displays TDM ports information. |
|
detail |
Display detailed TDM ports information. |
N/A.
Use this command to display general or detailed information on a specified list of TDM ports.
Print
this page
Email this topic
Feedback
View PDF
Download EPUB
E4G-400.3 # sh port {port_list} tdm information
Port Flags Link Line Clock #
State Coding Source PW
================================================================================
31 EeMcCRt---------- ready HDB3 Line 1
32 ETS-C-t---------- ready B8ZS CCR 2
33 ETF-C-ts--------- active B8ZS CCR 3
34 DTU-r-tl--------- ready B8ZS CCR 1
35 EeU---t---------- ready AMI CCR 1
36 EeB-CRt---------- ready HDB3 CCR 1
================================================================================
> indicates Port Display Name truncated past 8 characters
Flags : (B) E1 Basic Frame, (c) CRC-4, (C) Channel Associated Signaling,
(D) Port Disabled, (e) E1 Hierarchy, (E) Port Enabled,
(F) Extended Super Framed, (l) T1 Long-Haul Cable Length,
(M) Multi-framed, (r) Robbed Bit signaling,
(R) Clock Recovery Enabled, (s) T1 Short-Haul Cable Length,
(S) Super-framed, (t) TDM Circuit, (T) T1 Hierarchy,
(U) Unframed
Clock Source:
(CCR) CES pseudo-wire Recovered Clock
E4G-400.5 # show port {port_list} tdm information detail
Port: 1
Admin state : Enabled
Link State : Ready
Link Counter : Up 0 time(s)
Framing : E1 Multi-frame, CRC-4 Enabled
Signaling : Channel Associated Signaling
Line Coding : HDB3
Clock Source : Line
Clock Recovery : Disabled
Recovered Clock Quality : QL_DNU
Transmit Clock Quality : QL_DNU
Protocol : TDM Circuit
Loopback : Disabled
Idle Code : 10
TDM Service Configuration:
Name : cesopBundle1
Time slots : 1-10, 11-20
Name : cesopBundle2
Time slots : 21-30
Port: 2
Admin state : Enabled
Link State : Ready
Link Counter : Up 0 time(s)
Framing : E1 Unframed
Line Coding : HDB3
Clock Source : CES pseudo-wire recovered (satop21)
Clock Recovery : Enabled
Recovered Clock Quality : QL_PRC
Transmit Clock Quality : QL_DNU
Protocol : TDM Circuit
Loopback : Enabled (Network Payload)
Idle Code : 10
TDM Service Configuration:
Name : satopBundle1
Port: 3
Admin state : Enabled
Link State : Ready
Link Counter : Up 0 time(s)
Framing : T1 Unframed
Line Coding : B8ZS
Cable Length : Short-Haul, 550-660 feet
Clock Source : CES pseudo-wire recovered (satop22)
Clock Recovery : Disabled
Recovered Clock Quality : QL_DNU
Transmit Clock Quality : QL_DNU
Protocol : TDM Circuit
Loopback : Enabled (Network Payload)
Idle Code : 10
TDM Service Configuration:
Name : satopBundle2
Port: 4
Admin state : Enabled
Link State : Ready
Link Counter : Up 0 time(s)
Framing : T1 Unframed
Line Coding : B8ZS
Cable Length : Long-Haul, > 660 feet
Receiver Gain : 22.5dB
Clock Source : CES pseudo-wire recovered (satop23)
Clock Recovery : Enabled
Recovered Clock Quality : QL_PRS
Transmit Clock Quality : QL_PRS
Protocol : TDM Circuit
Loopback : Enabled (Local)
Idle Code : 10
TDM Service Configuration:
Name : satopBundle3
Port: 5
Admin state : Enabled
Link State : Ready
Link Counter : Up 0 time(s)
Framing : T1 Framed
Signaling : Robbed Bit
Line Coding : B8ZS
Cable Length : Long-Haul, > 660 feet
Receiver Gain : 22.5dB
Clock Source : CES pseudo-wire recovered (cesop1)
Clock Recovery : Disabled
Recovered Clock Quality : QL_DNU
Transmit Clock Quality : QL_DNU
Protocol : TDM Circuit
Loopback : Enabled (Local)
Idle Code : 10
TDM Service Configuration:
Name : cesopBundle1
Time slots : 1-10, 11-20
This command was first available in ExtremeXOS 15.1.
This command is available on the cell site routers (E4G-200 and E4G-400).