Displays the status of one or more processes being copied from the master node to the backup node.
| process | Specifies the name of the processes being copied. |
N/A.
This command displays, in percentages, the amount of internal state copying completed by each process and the traffic statistics between the process on both the master and the backup nodes.
This command is also helpful in debugging synchronization problems that occur at run-time. To check the status of synchronizing the nodes, use the show switch command.
Depending on the software version running on your switch and the type of switch you have, additional or different checkpoint status information may be displayed.
The following command displays the checkpointing status and the traffic statics of all of the processes between the master and the backup nodes:
# show checkpoint-data
Process Tx Rx Errors Sent Total % Chkpt Debug-info
----------------------------------------------------------------------------
devmgr 3812 1731 0 3 3 100% ON OK 1 (00008853)
dirser 0 0 0 0 0 0% ON OK 1 (000008D3)
ems 5 0 0 0 0 100% ON OK 1 (000008D3)
nodemgr 0 0 0 0 0 0% ON OK 1 (000008D3)
snmpSubagent 0 0 0 0 0 0% ON OK 1 (000018D3)
snmpMaster 0 0 0 0 0 0% ON OK 1 (000008D3)
cli 0 0 0 0 0 0% ON OK 1 (000018D3)
edp 0 0 0 0 0 0% ON OK 1 (000008D3)
cfgmgr 82 82 0 1 1 100% ON OK 1 (000018D3)
elrp 0 0 0 0 0 0% ON OK 1 (000008D3)
vlan 1047 1 0 0 0 100% ON OK 1 (000008D3)
aaa 0 0 0 0 0 0% ON OK 1 (000008D3)
fdb 957 2 0 0 0 100% ON OK 1 (000008D3)
msgsrv 0 0 0 0 0 100% ON OK 1 (000008D3)
eaps 0 0 0 0 0 0% ON OK 1 (000008D3)
stp 1 0 0 0 0 0% ON OK 1 (000008D3)
esrp 1 0 0 0 0 100% ON OK 1 (000008D3)
polMgr 0 0 0 0 0 0% ON OK 1 (000008D3)
mcmgr 2 2 0 0 0 100% ON OK 1 (000008D3)
acl 0 0 0 0 0 100% ON OK 1 (000008D3)
netLogin 0 0 0 0 0 0% ON OK 1 (000008D3)
ospf 0 0 0 0 0 0% ON OK 1 (000008D3)
netTools 1 0 0 0 0 100% ON OK 1 (000008D3)
telnetd 0 0 0 0 0 0% ON OK 1 (000008D3)
rtmgr 4 4 0 0 0 100% ON OK 1 (000008D3)
vrrp 378 0 0 0 0 0% ON OK 1 (000008D3)
tftpd 0 0 0 0 0 0% ON OK 1 (000008D3)
thttpd 0 0 0 0 0 0% ON OK 1 (000008D3)
rip 0 0 0 0 0 0% ON OK 1 (000008D3)
dosprotect 0 0 0 0 0 0% ON OK 1 (000008D3)
epm 0 0 0 0 0 0% ON OK 1 (000008D3)
hal 0 0 0 0 0 0% ON OK 1 (000008D3)
bgp 0 0 0 0 0 0% ON OK 1 (000008D3)
pim 0 0 0 0 0 0% ON OK 1 (000008D3)
etmon 185 185 0 0 0 100% ON OK 1 (000008D3)
Flags : S - Server started, c - Client started, D - Checkpoint dependency satisfied
C - Checkpointing is ON, f - No config dependency, N - DMLIB not in sync
R - CM Backend not ready, l - Process is loading config, L - Process config is loaded
I - IPML connection alive, n - Backup process not in sync with Primary process
To view the output for a specific process, use the process option. The following command displays detailed information for the STP process:
# show checkpoint-data stp Process Tx Rx Errors Sent Total % Chkpt Debug-info ---------------------------------------------------------------------------- stp 1 0 0 0 0 0% ON OK 1 (000008D3)
This command was first available in ExtremeXOS 10.1.
An error count was added to the output in ExtremeXOS 11.1.
IPML connection alive flag added in ExtremeXOS 22.5.
The "n" flag for the backup process being out of sync was added in ExtremeXOS 31.1.
This command is available only on SummitStack.