show stacking detail

show stacking {node-address node_address | slot slot_number} detail

Description

This command displays information about a specified node.

Syntax Description

node_address Specifies the MAC address of a node in the stack. To view the MAC addresses for all nodes in a stack, enter the show stacking command.
slot_number Specifies the slot number of the target node. To view the slot numbers, enter the show stacking command.

Default

N/A.

Usage Guidelines

If no node is specified, the output is generated for all nodes in the stack topology. If the specified node does not exist, an error message appears. The slot parameter is available only for active nodes in the same active topology as the node on which the command is run. The node-address parameter is always available.

Current information represents stacking states and configured values that are currently in effect. Configured information is that which takes effect at node reboot only. Thus, differences between values in use and values configured can be seen here. The advantages of this command over the show stacking configuration command is that the values in use and the configured values are fully expanded without the need for flags. You can also see the port state information of the node(s).

The roles values are: Master, Backup, Standby, and none.

License level restrictions can be Edge, Advanced Edge, or Core.

If one of the fields in the example below is missing on your switch, you switch does not support the feature that the field represents.

Example

The following is a sample output of this command:

Slot-1 Stack.33 # show stacking slot 1 detail
Stacking Node 00:04:96:26:6b:ec information:
Current:
Stacking                  : Enabled
Role                      : Master
Priority                  : Automatic
Slot number               : 1
Stack state               : Active
Master capable?           : Yes
Stacking protocol         : Enhanced
License level restriction : <none>
In active topology?       : Yes
Factory MAC address       : 00:04:96:26:6b:ec
Stack MAC address         : 02:04:96:26:6b:ec
Alternate IP address      : <none>
Alternate gateway         : <none>
Stack Port 1:
State                  : Operational
Blocked?               : No
Control path active?   : Yes
Selection              : Alternate (23)
Stack Port 2:
State                  : Operational
Blocked?               : Yes
Control path active?   : Yes
Selection              : Native
Configured:
Stacking                  : Enabled
Master capable?           : Yes
Slot number               : 1
Stack MAC address         : 02:04:96:26:6b:ec
Stacking protocol         : Enhanced
License level restriction : <none>
Stack Port 1:
Selection              : Alternate (23)
Stack Port 2:
Selection              : Native
The following example shows the stacking information for a ExtremeSwitching 5520 series switch node:
# show stacking detail
Stacking Node 00:04:96:f1:b8:00 information:
   Current:
      Stacking                  : Disabled
      Role                      : Master
      Priority                  : Automatic
      Slot number               : N/A
      Stack state               : Disabled
      Master capable?           : N/A
      Stacking protocol         : Enhanced
      License level restriction : Base
      In active topology?       : No
      Factory MAC address       : 00:04:96:f1:b8:00
      Stack MAC address         : N/A
      Alternate IP address      : <none>
      Alternate gateway         : <none>
      Stack Port 1:
         State                  : Link down
         Blocked?               : No
         Control path active?   : No
      Stack Port 2:
         State                  : Link Down
         Blocked?               : No
         Control path active?   : No
   Configured:
      Stacking                  : Disabled
      Master capable?           : Yes
      Slot number               : 1
      Stack MAC address         : 02:04:96:f1:b8:00
      Stacking protocol         : Enhanced
      License level restriction : Base

History

This command was first available in ExtremeSwitching 12.0.

The Stacking protocol and Stack Port Selection fields were added in ExtremeSwitching 12.5.

Licensing information specific to ExtremeSwitching 5520 series switches was added in ExtremeXOS 31.1.

Platform Availability

This command is available with all licenses and platforms that support the SummitStack feature. For information about which licenses and platforms support the SummitStack feature, see the Switch Engine 32.2 Feature License Requirements document.