Switching

Click to expand in new window

Protected Ports Log Messages

Component Message Cause
Protected Ports Protected Port: failed to save configuration This appears when the protected port configuration cannot be saved.
Protected Ports protectedPortCnfgrInitPhase1Process: Unable to create r/w lock for protected Port This appears when protectedPortCfgRWLock Fails.
Protected Ports protectedPortCnfgrInitPhase2Process: Unable to register for VLAN change callback This appears when nimRegisterIntfChange with VLAN fails.
Protected Ports Cannot add interface xxx to group yyy This appears when an interface could not be added to a particular group.
Protected Ports unable to set protected port group This appears when a dtl call fails to add interface mask at the driver level.
Protected Ports Cannot delete interface xxx from group yyy This appears when a dtl call to delete an interface from a group fails.
Protected Ports Cannot update group YYY after deleting interface XXX This message appears when an update group for a interface deletion fails.
Protected Ports Received an interface change callback while not ready to receive it This appears when an interface change call back has come before the protected port component is ready.
Click to expand in new window

IP Subnet VLANS Log Messages

Component Message Cause
IP subnet VLANs ERROR vlanIpSubnetSubnetValid:Invalid subnet This occurs when an invalid pair of subnet and netmask has come from the CLI.
IP subnet VLANs IP Subnet Vlans: failed to save configuration This message appears when save configuration of subnet vlans failed.
IP subnet VLANs vlanIpSubnetCnfgrInitPhase1Process: Unable to create r/w lock for vlanIpSubnet This appears when a read/write lock creations fails.
IP subnet VLANs vlanIpSubnetCnfgrInitPhase2Process: Unable to register for VLAN change callback This appears when this component unable to register for vlan change notifications.
IP subnet VLANs vlanIpSubnetCnfgrFiniPhase1Process: could not delete avl semaphore This appears when a semaphore deletion of this component fails.
IP subnet VLANs vlanIpSubnetDtlVlanCreate: Failed This appears when a dtl call fails to add an entry into the table.
IP subnet VLANs vlanIpSubnetSubnetDeleteApply: Failed This appears when a dtl fails to delete an entry from the table.
IP subnet VLANs vlanIpSubnetVlanChangeCallback: Failed to add an Entry This appears when a dtl fails to add an entry for a vlan add notify event.
IP subnet VLANs vlanIpSubnetVlanChangeCallback: Failed to delete an Entry This appears when a dtl fails to delete an entry for an vlan delete notify event.
Click to expand in new window

Mac-based VLANs Log Messages

Component Message Cause
MAC based VLANs MAC VLANs: Failed to save configuration This message appears when save configuration of Mac vlans failed.
MAC based VLANs vlanMacCnfgrInitPhase1Process: Unable to create r/w lock for vlanMac This appears when a read/write lock creations fails.
MAC based VLANs Unable to register for VLAN change callback This appears when this component unable to register for vlan change notifications.
MAC based VLANs vlanMacCnfgrFiniPhase1Process: could not delete avl semaphore This appears when a semaphore deletion of this component fails.
MAC based VLANs vlanMacAddApply: Failed to add an entry This appears when a dtl call fails to add an entry into the table.
MAC based VLANs vlanMacDeleteApply: Unable to delete an Entry This appears when a dtl fails to delete an entry from the table.
MAC based VLANs vlanMacVlanChangeCallback: Failed to add an entry This appears when a dtl fails to add an entry for a vlan add notify event.
MAC based VLANs vlanMacVlanChangeCallback: Failed to delete an entry This appears when a dtl fails to delete an entry for an vlan delete notify event.
Click to expand in new window

802.1X Log Messages

Component Message Cause
802.1X function: Failed calling dot1xIssueCmd 802.1X message queue is full.
802.1X function: EAP message not received from server RADIUS server did not send required EAP message.
802.1X function: Out of System buffers 802.1X cannot process/transmit message due to lack of internal buffers.
802.1X function: could not set state to authorized/unauthorized, intf xxx DTL call failed setting authorization state of the port.
802.1X dot1xApplyConfigData: Unable to enable/disable dot1x in driver DTL call failed enabling/disabling 802.1X.
802.1X dot1xSendRespToServer: dot1xRadiusAccessRequestSend failed Failed sending message to RADIUS server.
802.1X dot1xRadiusAcceptProcess: error calling radiusAccountingStart, ifIndex = xxx Failed sending accounting start to RADIUS server.
802.1X function: failed sending terminate cause, intf xxx Failed sending accounting stop to RADIUS server.
Click to expand in new window

IGMP Snooping Log Messages

Component Message Cause
IGMP (Internet Group Management Protocol) Snooping function: osapiMessageSend failed IGMP Snooping message queue is full.
IGMP Snooping Failed to set global igmp snooping mode to xxx Failed to set global IGMP Snooping mode due to message queue being full.
IGMP Snooping Failed to set igmp snooping mode xxx for interface yyy Failed to set interface IGMP Snooping mode due to message queue being full.
IGMP Snooping Failed to set igmp mrouter mode xxx for interface yyy Failed to set interface multicast router mode due to IGMP Snooping message queue being full.
IGMP Snooping Failed to set igmp snooping mode xxx for vlan yyy Failed to set VLAN IGM Snooping mode due to message queue being full.
IGMP Snooping Failed to set igmp mrouter mode%d for interface xxx on Vlan yyy Failed to set VLAN multicast router mode due to IGMP Snooping message queue being full.
IGMP Snooping snoopCnfgrInitPhase1Process: Error allocating small buffers Could not allocate buffers for small IGMP packets.
IGMP Snooping snoopCnfgrInitPhase1Process: Error allocating large buffers Could not allocate buffers for large IGMP packets.
Click to expand in new window

GARP/GVRP/GMRP Log Messages

Component Message Cause
GARP/GVRP/

GMRP

garpSpanState, garpIfStateChange, GarpIssueCmd, garpDot1sChangeCallBack, garpApiCnfgrCommand, garpLeaveAllTimerCallback, garpTimerCallback: QUEUE SEND FAILURE: The garpQueue is full, logs specifics of the message content like internal interface number, type of message, and so forth.
GARP/GVRP/

GMRP

GarpSendPDU: QUEUE SEND FAILURE The garpPduQueue is full, logs specific of the GPDU, internal interface number, vlan id, buffer handle, and so forth.
GARP/GVRP/

GMRP

garpMapIntfIsConfigurable, gmrpMapIntfIsConfigurable: Error accessing GARP/GMRP config data for interface %d in garpMapIntfIsConfigurable. A default configuration does not exist for this interface. Typically a case when a new interface is created and has no preconfiguration.
GARP/GVRP/

GMRP

garpTraceMsgQueueUsage: garpQueue usage has exceeded fifty/eighty/ninety percent Traces the build up of message queue. Helpful in determining the load on GARP.
GARP/GVRP/

GMRP

gid_destroy_port: Error Removing port %d registration for vlan-mac %d - %02X:%02X:%02X:%02X:%02X:%02X Mismatch between the gmd (gmrp database) and MFDB.
GARP/GVRP/

GMRP

gmd_create_entry: GMRP failure adding MFDB entry: vlan %d and address %s MFDB table is full.
Click to expand in new window

802.3ad Log Messages

Component Message Cause
802.3ad dot3adReceiveMachine: received default event %x Received a LAG (Link Aggregation Group) PDU and the RX state machine is ignoring this LAGPDU.
802.3ad dot3adNimEventCompletionCallback, dot3adNimEventCreateCompletionCallback: DOT3AD: notification failed for event(%d), intf(%d), reason(%d) The event sent to NIM was not completed successfully.
Click to expand in new window

FDB Log Message

Component Message Cause
FDB (forwarding database) fdbSetAddressAgingTimeOut: Failure setting fid %d address aging timeout to %d Unable to set the age time in the hardware.
Click to expand in new window

Double VLAN Tag Log Message

Component Message Cause
Double Vlan Tag dvlantagIntfIsConfigurable: Error accessing dvlantag config data for interface %d A default configuration does not exist for this interface. Typically a case when a new interface is created and has no preconfiguration.
Click to expand in new window

IPv6 Provisioning Log Message

Component Message Cause
IPV6 Provisioning ipv6ProvIntfIsConfigurable: Error accessing IPv6 Provisioning config data for interface %d A default configuration does not exist for this interface. Typically a case when a new interface is created and has no preconfiguration.
Click to expand in new window

MFDB Log Message

Component Message Cause
MFDB mfdbTreeEntryUpdate: entry does not exist Trying to update a non existing entry.
Click to expand in new window

802.1Q Log Messages

Component Message Cause
802.1Q dot1qIssueCmd: Unable to send message %d to dot1qMsgQueue for vlan %d - %d msgs in queue dot1qMsgQueue is full.
802.1Q dot1qVlanCreateProcess: Attempt to create a vlan with an invalid vlan id %d ;

VLAN %d not in range,

This accommodates for reserved vlan IDs: 4094 - x.
802.1Q dot1qMapIntfIsConfigurable: Error accessing DOT1Q config data for interface %d in dot1qMapIntfIsConfigurable. A default configuration does not exist for this interface. Typically a case when a new interface is created and has no preconfiguration.
802.1Q dot1qVlanDeleteProcess: Deleting the default VLAN Typically encountered during clear Vlan and clear config.
802.1Q dot1qVlanMemberSetModify, dot1qVlanTaggedMemberSetModify: Dynamic entry %d can only be modified after it is converted to static If this vlan is a learnt via GVRP then we cannot modify its member set via management.
802.1Q dtl failure when adding ports to vlan id %d - portMask = %s Failed to add the ports to VLAN entry in hardware.
802.1Q dtl failure when deleting ports from vlan id %d - portMask = %s Failed to delete the ports for a VLAN entry from the hardware.
802.1Q dtl failure when adding ports to tagged list for vlan id %d - portMask = %s Failed to add the port to the tagged list in hardware.
802.1Q dtl failure when deleting ports from tagged list for vlan id %d - portMask = %s" Failed to delete the port to the tagged list from the hardware.
802.1Q dot1qTask: unsuccessful return code on receive from dot1qMsgQueue: %08x" Failed to receive the dot1q message from dot1q message queue.
802.1Q Unable to apply VLAN creation request for VLAN ID %d, Database reached MAX VLAN count! Failed to create VLAN ID, VLAN Database reached maximum values.
802.1Q Attempt to create a vlan (%d) that already exists Creation of the existing Dynamic VLAN ID from the CLI.
802.1Q DTL call to create VLAN %d failed with rc %d" Failed to create VLAN ID in hardware.
802.1Q Problem unrolling data for VLAN %d Failed to delete VLAN from the VLAN database after failure of VLAN hardware creation.
802.1Q VLan %d does not exist Failed to delete VLAN entry.
802.1Q VLan %d requestor type %d does not exist Failed to delete dynamic VLAN ID if the given requestor is not valid.
802.1Q Can not delete the VLAN, Some unknown component has taken the ownership! Failed to delete, as some unknown component has taken the ownership.
802.1Q Not valid permission to delete the VLAN %d requestor %d Failed to delete the VLAN ID as the given requestor and VLAN entry status are not same.
802.1Q VLAN Delete Call failed in driver for vlan %d Failed to delete VLAN ID from the hardware.
802.1Q Problem deleting data for VLAN %d Failed to delete VLAN ID from the VLAN database.
802.1Q Dynamic entry %d can only be modified after it is converted to static Failed to modify the VLAN group filter
802.1Q Cannot find vlan %d to convert it to static Failed to convert Dynamic VLAN to static VLAN. VLAN ID not exists.
802.1Q Only Dynamically created VLANs can be converted Error while trying to convert the static created VLAN ID to static.
802.1Q Cannot modify tagging of interface %s to non existence vlan %d" Error for a given interface sets the tagging property for all the VLANs in the vlan mask.
802.1Q Error in updating data for VLAN %d in VLAN database Failed to add VLAN entry into VLAN database.
802.1Q DTL call to create VLAN %d failed with rc %d Failed to add VLAN entry in hardware.
802.1Q Not valid permission to delete the VLAN %d Failed to delete static VLAN ID. Invalid requestor.
802.1Q Attempt to set access vlan with an invalid vlan id %d Invalid VLAN ID.
802.1Q Attempt to set access vlan with (%d) that does not exist VLAN ID not exists.
802.1Q VLAN create currently underway for VLAN ID %d Creating a VLAN which is already under process of creation.
802.1Q VLAN ID %d is already exists as static VLAN Trying to create already existing static VLAN ID.
802.1Q Cannot put a message on dot1q msg Queue, Returns:%d Failed to send Dot1q message on Dot1q message Queue.
802.1Q Invalid dot1q Interface: %s Failed to add VLAN to a member of port.
802.1Q Cannot set membership for user interface %s on management vlan %d Failed to add VLAN to a member of port.
802.1Q Incorrect tagmode for vlan tagging. tagmode: %d Interface: %s Incorrect tagmode for VLAN tagging.
802.1Q Cannot set tagging for interface %d on non existent VLAN %d" The VLAN ID does not exist.
802.1Q Cannot set tagging for interface %d which is not a member of VLAN %d Failure in Setting the tagging configuration for a interface on a range of VLAN.
802.1Q VLAN create currently underway for VLAN ID %d" Trying to create the VLAN ID which is already under process of creation.
802.1Q VLAN ID %d already exists Trying to create the VLAN ID which is already exists.
802.1Q Failed to delete, Default VLAN %d cannot be deleted Trying to delete Default VLAN ID.
802.1Q Failed to delete, VLAN ID %d is not a static VLAN Trying to delete Dynamic VLAN ID from CLI.
802.1Q Requestor %d attempted to release internal VLAN %d: owned by %d -
Click to expand in new window

802.1S Log Messages

Component Message Cause
802.1S dot1sIssueCmd: Dot1s Msg Queue is full!!!!Event: %u, on interface: %u, for instance: %u The message Queue is full.
802.1S dot1sStateMachineRxBpdu(): Rcvd BPDU Discarded The current conditions, like port is not enabled or we are currently not finished processing another BPDU on the same interface, does not allow us to process this BPDU.
802.1S dot1sBpduTransmit(): could not get a buffer Out of system buffers.
Click to expand in new window

Port Mac Locking Log Message

Component Message Cause
Port Mac Locking pmlMapIntfIsConfigurable: Error accessing PML config data for interface %d in pmlMapIntfIsConfigurable. A default configuration does not exist for this interface. Typically a case when a new interface is created and has no preconfiguration.
Click to expand in new window

Protocol-based VLANs Log Messages

Component Message Cause
Protocol Based VLANs pbVlanCnfgrInitPhase2Process: Unable to register NIM callback Appears when nimRegisterIntfChange fails to register pbVlan for link state changes.
Protocol Based VLANs pbVlanCnfgrInitPhase2Process: Unable to register pbVlan callback with VLANs Appears when VLANRegisterForChange fails to register pbVlan for VLAN changes.
Protocol Based VLANs pbVlanCnfgrInitPhase2Process: Unable to register pbVlan callback with nvStore Appears when nvStoreRegister fails to register save and restore functions for configuration save.