This command displays configuration settings associated with the switch's network interface. The network interface is the logical interface used for in-band connectivity with the switch via any of the switch's front panel ports. The configuration parameters associated with the switch's network interface do not affect the configuration of the front panel ports through which traffic is switched or routed. The network interface is always considered to be up, whether any member ports are up; therefore, the show network command will always show Interface Status as Up.
| Format | show network |
| Modes |
|
| Interface Status | The network interface status; it is always considered to be “up”. |
| IP Address | The IP address of the interface. The factory default value is 0.0.0.0. |
| Subnet Mask | The IP subnet mask for this interface. The factory default value is 0.0.0.0. |
| Default Gateway | The default gateway for this IP interface. The factory default value is 0.0.0.0. |
| IPv6 Administrative Mode | Whether enabled or disabled. |
| IPv6 Address/Length | The IPv6 address and length. |
| IPv6 Default Router | The IPv6 default router address. |
| Burned In MAC Address | The burned in MAC address used for in-band connectivity. |
| Locally Administered MAC Address | If desired, a locally administered MAC address can be configured for in-band connectivity. To take effect, 'MAC Address Type' must be set to 'Locally Administered'. Enter the address as twelve hexadecimal digits (6 bytes) with a colon between each byte. Bit 1 of byte 0 must be set to a 1 and bit 0 to a 0, that is, byte 0 should have the following mask 'xxxx xx10'. The MAC address used by this bridge when it must be referred to in a unique fashion. We recommend that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with dot1dStpPriority a unique Bridge Identifier is formed which is used in the Spanning Tree Protocol. |
| MAC Address Type | The MAC address which should be used for in-band connectivity. The choices are the burned in or the Locally Administered address. The factory default is to use the burned in MAC address. |
| Configured IPv4 Protocol | The IPv4 network protocol being used. The options are bootp | dhcp | none. |
| Configured IPv6 Protocol | The IPv6 network protocol being used. The options are dhcp | none. |
| DHCPv6 Client DUID | The DHCPv6 client‘s unique client identifier. This row is displayed only when the configured IPv6 protocol is dhcp. |
| IPv6 Autoconfig Mode | Whether IPv6 Stateless address autoconfiguration is enabled or disabled. |
| DHCP Client Identifier | The client identifier is displayed in the output of the command only if DHCP (Dynamic Host Configuration Protocol) is enabled with the client-id option on the network port. See network protocol dhcp. |
The following example shows CLI display output for the network port.
(admin) #show network Interface Status............................... Up IP Address..................................... 10.250.3.1 Subnet Mask.................................... 255.255.255.0 Default Gateway................................ 10.250.3.3 IPv6 Administrative Mode....................... Enabled IPv6 Prefix is ................................ fe80::210:18ff:fe82:64c/64 IPv6 Prefix is ................................ 2003::1/128 IPv6 Default Router is ........................ fe80::204:76ff:fe73:423a Burned In MAC Address.......................... 00:10:18:82:06:4C Locally Administered MAC address............... 00:00:00:00:00:00 MAC Address Type............................... Burned In Configured IPv4 Protocol ...................... None Configured IPv6 Protocol ...................... DHCP DHCPv6 Client DUID ............................ 00:03:00:06:00:10:18:82:06:4C IPv6 Autoconfig Mode........................... Disabled Management VLAN ID............................. 1 DHCP Client Identifier......................... 0fastpath-0010.1882.160B-vl1
Print
this page
Email this topic
Feedback
View PDF
Download EPUB