Understanding the SSH2 Client Functions on the Switch

An Extreme Networks switch can function as an SSH2 client. This means you can connect from the switch to a remote device running an SSH2 server and send commands to that device. You can also use SCP2 to transfer files to and from the remote device.

Note

ExtremeXOS 15.7.1 upgraded from openssh-3.9p1 to openssh-6.5p1. ExtremeXOS 21.1 adds the openssl-fips-ecp-2.0.9 open source library. ExtremeXOS 22.5 upgraded from openssh-6.5p1 to openssh-7.5p1. ExtremeXOS 30.7 upgraded from openssh-7.5p1 to openssh-8.1p1

Support for following ciphers and macs are removed in ExtremeXOS 30.7, since these are not supported in openssh 8.1p1:

Ciphers: blowfish-cbc, cast128-cbc, arcfour, arcfour256, arcfour128
MACs: hmac-ripemd160-etm@openssh.com, hmac-ripemd160, hmac-ripemd160@openssh.com

Note

When upgrading to ExtremeXOS 30.7, if unsupported ciphers/MACs are:

Enabled in the saved configuration, the configuration is ignored during configuration load. The dirty bit is set and an error message appears:. <Erro:exsshd.LoadCfgCipherUnsuprt> <Erro:exsshd.LoadCfgMACUnsuprt>.
Disabled (by default or intentional) in the saved configuration, the configuration is ignored silently during configuration load. The dirty bit is set and an error messages do not appear.

You do not need to enable SSH2 or generate an authentication key to use the SSH2 and SCP2 commands from the ExtremeXOS CLI.

Note

User-created VRs are supported only on the platforms listed for this feature in the ExtremeXOS 32.2 Feature License Requirements document.

To send commands to a remote system using SSH2, use the following command:
ssh2 {cipher [cipher} {mac mac} {compression [on | off]} {port port} {user username} {vr vr_name} user@host {remote_command}

The remote commands can be any command acceptable by the remote system. You can specify the login user name as a separate argument or as part of the user@host specification. If the login user name for the remote system is the same as your user name on the switch, you can omit the username parameter entirely.

For example, to obtain a directory listing from a remote Linux system with IP address 10.10.0.2 using SSH2, enter the following command:ssh2 admin@10.10.0.2 ls
To initiate a file copy from a remote system to the switch using SCP2, use the following command:
scp2 {cipher cipher} {mac mac} {compression [on | off]} {port port} {vr vr_name} [ user@host:file local-file | local-file user@host:file ]
For example, to copy the configuration file test.cfg on host system1 to the switch, enter the following command:
```
scp2 admin@system1:test.cfg localtest.cfg
```
To initiate a file copy to a remote system from the switch using SCP2, use the following command:
scp2 {cipher cipher} {mac mac} {compression [on | off]} {port port} {vr vr_name} [ user@host:file local-file | local-file user@host:file ]
For example, to copy the configuration file engineering.cfg from the switch to host system1, enter the following command:
```
scp2 engineering.cfg admin@system1:engineering.cfg
```

Switching

Routing

Wireless

Management & Automation

Analytics & Visibility

Security & Access Control

Remote

Cloud

Security

Machine Learning

Campus Fabric

Data Center Fabric

Internet of Things

Wi-Fi 6

Primary & Secondary Education (K-12)

Retail

Service Providers

Federal Government

Manufacturing

Higher Education

Healthcare

Hospitality

State & Local Government

Sports & Public Venues

Support Portal

Knowledge Base

Documentation

End of Sale

Policies & Warranties

Training & Courses

Maintenance Services

Premier Services

Professional Services

Managed Services

Understanding the SSH2 Client Functions on the Switch