ENTERASYS-CONVERGENCE-END-POINT-MIB

Table/Group Supported Variables Comments
etsysConvEndPointGlobalConfigEnable

When set to enabled(1) this object activates the current Convergence End Point configuration. When set to disabled(2) this MIB SHALL be configurable, but MUST NOT be applied, all entries will be removed from the etsysConvEndPointConnMacTable and the etsysConvEndPointConnPortTable, and any policies that have been changed as a result of End Point detection will revert to their default states. Maintaining the value of this object across agent reboots is REQUIRED.

Read-write.

etsysConvEndPointGlobalConfigTable This table represents all Convergence End Point types supported by this entity, and provides a default policy profile for each Convergence End Point type.

Not-accessible.

etsysConvEndPointGlobalConfigEntry Defines the default policy to be applied when this type of Convergence End Point is detected or discovered.

Not-accessible.

etsysConvEndPointGlobalDefaultPolicyIndex The policy that should be applied for this type of Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If no such policy index exists, then no policy will be applied when this type of Convergence End Point is detected or discovered. The value zero is not a valid etsysPolicyProfileIndex, so zero indicates that no policy should be applied. Maintaining the value of this object across system reboots is REQUIRED.

Read-write.

etsysConvEndPointProtocolConfigTable This table provides control of Convergence End Point detection and discovery on a per interface and per Convergence End Point type basis. Maintaining the values of this table across system reboots is REQUIRED.

Not-accessbile.

etsysConvEndPointProtocolConfigEntry The current Convergence End Point detection and discovery status for an interface.

Not-accessible.

etsysConvEndPointProtocolEndPointType The Convergence End Point type.

Not-accessible.

etsysConvEndPointProtocolEnable When set to enabled(1), Convergence End Point detection and discovery will be enabled on this interface for the Convergence End Point type specified. When set to disabled(2), the Convergence End Points that have been discovered or detected on this interface of the type specified will be removed from the etsysConvEndPointConnMacTable and the etsysConvEndPointConnPortTable. After all of the End Points have been removed from an interface the policy on that interface will revert to its default state.

Read-write.

etsysConvEndPointGlobalConfigAccountEnable When enabled(1), RADIUS accounting start, interim and stop frames are sent to the configured RADIUS server(s). When disabled(2), accounting packets are not sent to the RADIUS server.

Read-write.

etsysConvEndPointConnMacTable This table provides information on each of the Convergence End Points that has been discovered or detected by this entity. Maintaining the value of this object across system reboots is NOT REQUIRED.

Not-accessible.

etsysConvEndPointConnMacEntry Information about an individual Convergence End Point.

Not-accessible.

etsysConvEndPointConnMacMacAddress The MAC address of this Convergence End Point.

Not-accessible.

etsysConvEndPointConnMacPortNumber The interface on which this Convergence End Point was detected or discovered.

Read-only.

etsysConvEndPointConnMacEndPointType The type of Convergence End Point described by this row.

Read-only.

etsysConvEndPointConnMacPolicyIndex The policy applied for this Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does not currently exist, or never did exist, then a zero MUST be returned.

Read-only.

etsysConvEndPointConnMacDiscoveryTime The time and date that this Convergence End Point was detected or discovered.

Read-only.

etsysConvEndPointConnMacFirmwareVersion This is the firmware version of the discovered Convergence End Point. If this information is not available via the detection protocol then a zero length string MUST be returned.

Read-only.

etsysConvEndPointConnMacInetAddressType The address type of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return 'unknown'

Read-only.

etsysConvEndPointConnMacInetAddress The address of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return a zero length string.

Read-only.

etsysConvEndPointConnPortTable This table provides a mapping from the entities interfaces to discovered Convergence End Points. Maintaining the value of this object across system reboots is NOT REQUIRED.

Not-accessible.

etsysConvEndPointConnPortEntry Information about an individual Convergence End Point.

Not-accessible.

etsysConvEndPointConnPortMacAddress The MAC address of the discovered or detected Convergence End Point.

Read-only.

etsysCEPConnMacTable This table provides information on each of the Convergence End Points that has been discovered or detected by this entity. Maintaining the value of this object across system reboots is NOT REQUIRED.

Not-accessible.

etsysCEPConnMacEntry Information about an individual Convergence End Point (CEP).

Not-accessible.

etsysCEPConnMacEndPointType The type of Convergence End Point described by this row.

Read-only.

etsysCEPConnMacPolicyIndex The type of Convergence End Point described by this row.

Read-only.

etsysCEPConnMacPolicyIndex The policy applied for this Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does not currently exist, or never did exist, then a zero MUST be returned.

Read-only.

etsysCEPConnMacDiscoveryTime The time and date that this Convergence End Point was detected or discovered.

Read-only.

etsysCEPConnMacFirmwareVersion This is the firmware version of the discovered Convergence End Point. If this information is not available via the detection protocol then a zero length string MUST be returned.

Read-only.

etsysCEPConnMacInetAddressType The address type of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return 'unknown'.

Read-only.

etsysCEPConnMacInetAddress The address of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return a zero length string.

Read-only.

etsysConvEndPointDetectionMaxEntries This value represents the maximum number of entries allowed in the etsysConvEndPointDetectionTable.

Read-only.

etsysConvEndPointDetectionTable A table that describes the IP address and IP port based Convergence End Point detection parameters. Packets on interfaces that are configured to detect End Points, via the etsysConvEndPointProtocolConfigTable, that are defined in this table are inspected to determine if a Convergence End Point exists on that interface. Rules applying to Convergence End Point types that are configured for detection are evaluated according to the following:
  1. If etsysConvEndPointDetectionProtocol does not have any bits set, this indicates that the port based detection should not be performed, proceed to step 2. Otherwise the value in etsysConvEndPointDetectionProtocol is evaluated against the protocol field in the IP header, if it is of a, or the, type specified then the destination port must be between the values of etsysConvEndPointDetectionPortLow and etsysConvEndPointDetectionPortHigh, inclusive.
  2. If the etsysConvEndPointDetectionAddr is null, this indicates that no detection address check should be performed, consider the End Point detected. Otherwise the value the of etsysConvEndPointDetectionAddr will be masked with the value of etsysConvEndPointDetectionAddrMask, via a bitwise AND operation, and this value will be compared with the destination IP address that has also been masked with the value of etsysConvEndPointDetectionAddrMask, via a bitwise AND operation, if they are equal then consider the End Point detected.

If there are no rows in this table that are in the active state then the following pseudo entries describe the behavior of the IP based Convergence End Point detection.

EndPointType siemens

Protocol { { udp, tcp } }

PortLow 4060

PortHigh 4060

AddrType unknown

Addr ' '

AddrMaskType unknown

AddrMask ''

EndPointType h323

Protocol { { udp, tcp } }

PortLow 1718

PortHigh 1720

AddrType ipv4

Addr '224.0.1.41'

AddrMaskType ipv4

AddrMask '255.255.255.255'

EndPointType sip

Protocol { { udp, tcp } }

PortLow 5060

PortHigh 5060

AddrType ipv4

Addr '224.0.1.75'

AddrMaskType ipv4

AddrMask '255.255.255.255'

EndPointType h323

Protocol { { udp, tcp } }

PortLow 1718

PortHigh 1720

AddrType unknown

Addr ''

AddrMaskType unknown

AddrMask ''

EndPointType sip

Protocol { { udp, tcp } }

PortLow 5060

PortHigh 5060

AddrType unknown

Addr ''

AddrMaskType unknown

AddrMask ''

If one or more entries in this table are active the active entries will define the IP based detection behavior in its entirety. Maintaining entries in this table across system reboots is REQUIRED for entries with an etsysConvEndPointDetectionRowStatus value of active(1).

Not-accessible.

etsysConvEndPointDetectionEntry