Simple Ring Configuration Example

The following example shows how to set up a simple Extended Edge Switching ring configuration (see CB with Simple Ring Topology).
Click to expand in new window
CB with Simple Ring Topology
  1. Attach BPEs.
  2. On the CB, enable VPEX mode:
    X465.1 # enable vpex
    X465.1 # reboot
    Are you sure you want to reboot the switch? (y/N) Yes
    Slot-1 VPEX X465.1 #
    Note

    Note

    After reboot, command prompt changes to show that you are in VPEX mode.
  3. Configure slot identifiers associated with the first-tier BPEs in cascades 1 and 2:
    Slot-1 VPEX X465.1 # configure vpex port 1:10 slot 110
    WARNING: This command will remove VLAN membership from the
             port 1:10.
             Do you want to continue? (y/N)Yes
    
    Slot-1 VPEX X465.2 # configure vpex port 1:20 slot 120
    WARNING: This command will remove VLAN membership from the
             port 1:20.
             Do you want to continue? (y/N)Yes
    
    Slot-1 VPEX X465.3 # show slot
    Slots    Type                 Configured           State       Ports   Flags
    --------------------------------------------------------------------------------
    Slot-1   X465        X465        Operational   64    M
    Slot-110 V400-48p-10GE4                            Operational   52
    Slot-120 V400-48p-10GE4                            Operational   52
    Flags : M - Backplane link to Master is Active
            B - Backplane link to Backup is also Active
            D - Slot Disabled
            I - Insufficient Power (refer to "show power budget")
    
    Slot-1 VPEX X465.9 # show vpex
    Virtual Port Extender: Enabled
    Cascade
    Port     Slot
    =============
    1:10     110
    1:20     120
    Note

    Note

    Observe that the show slot command shows the CB as slot 1 with the two BPEs as slots 110 and 120.
    Note

    Note

    Observe that the show vpex command shows that ports 1:10 and 1:20 are the cascade ports connecting to the BPEs.
  4. Configure slot identifiers associated with the second-tier BPEs in cascades 1 and 2:
    Slot-1 VPEX X465.1 # configure vpex port 110:49 slot 130
    WARNING: This command will remove VLAN membership from the
             port 110:49.
             Do you want to continue? (y/N)Yes
    
    Slot-1 VPEX X465.2 # configure vpex port 120:49 slot 140
    WARNING: This command will remove VLAN membership from the
             port 120:49.
             Do you want to continue? (y/N)Yes
    
    Slot-1 VPEX X465.3 # show slot
    Slots    Type                 Configured           State       Ports   Flags
    --------------------------------------------------------------------------------
    Slot-1   X465        X465        Operational   64    M
    Slot-110 V400-48p-10GE4                            Operational   52
    Slot-120 V400-48p-10GE4                            Operational   52
    Slot-130 V400-48p-10GE4                            Operational   52
    Slot-140 V400-48p-10GE4                            Operational   52
    Flags : M - Backplane link to Master is Active
            B - Backplane link to Backup is also Active
            D - Slot Disabled
            I - Insufficient Power (refer to "show power budget")
    
    Slot-1 VPEX X465.9 # show vpex
    Virtual Port Extender: Enabled
    Cascade
    Port     Slot
    =============
    1:10     110
    1:20     120
    110:49   130
    120:49   140
    Note

    Note

    Observe that the show slot command shows the CB as slot 1 with the four BPEs as slots 110, 120, 130, and 140.
    Note

    Note

    Observe that the show vpex command shows that ports 1:10, 1:20, 110:49, and 120:49 are the cascade ports connecting to the BPEs.
  5. Connect the end of cascade 1 to cascade 2 to form the ring:
    <Noti:VPEX.Ring.Dtect> Slot-1: Ring detected between ports 140:49 and 130:49