show ports configuration

show ports {mgmt | port_list | tag tag} configuration {no-refresh | refresh}

Description

Displays port configuration statistics, in real time or snapshot.

Syntax Description

mgmt

Specifies the management port.

port_list

Specifies one or more ports or slots and ports.

tag

Specifies an 802.1Q or 802.1ad tag value.

no-refresh

Specifies a static snapshot of data.

refresh Specifies a continous refresh of output.

Default

Real-time statistics.

Usage Guidelines

If you do not specify a port number, range of ports, or tag value, configuration statistics are displayed for all ports. If you specify the no-refresh parameter, the system displays a snapshot of the data at the time you issue the command.

The tag value may be associated with either a VMAN or a VLAN (Virtual LAN).

This status information may be useful for your technical support representative if you have a network problem.

This command displays port configuration, which includes:
  • Virtual router.

  • Port state.

  • Link state.

  • Autonegotiation information.

  • Link speed.

  • Duplex mode.

  • Flow control.

  • Load sharing information.

  • Link media information.
    Note

    Note

    On 10 Gbps ports, the Media Primary column displays NONE when no module is installed, and SR, LR, or ER depending on the module installed when there is one present. Combination ports display Autonegotiation, Link speed, and Duplex mode information only for the current primary medium.

Example

The following command displays the port configuration for all ports on a Summit family switch:

show ports configuration
Port Configuration Monitor                              Fri Apr 13 10:22:29 2007
Port     Virtual    Port  Link  Auto   Speed      Duplex   Flow  Load   Media
router     State State Neg  Cfg Actual Cfg Actual Cntrl Master Pri Red
================================================================================
1        VR-Default  E      R    ON  AUTO       AUTO                   NONE UTP
2        VR-Default  E      R    ON  AUTO       AUTO                   NONE UTP
3        VR-Default  E      R    ON  AUTO       AUTO                   NONE UTP
4        VR-Default  E      R    ON  AUTO       AUTO                   NONE UTP
5        VR-Default  E      R    ON  AUTO       AUTO                   NONE
6        VR-Default  E      R    ON  AUTO       AUTO                   NONE
7        VR-Default  E      R   OFF   100       FULL                   SX
8        VR-Default  E      R    ON  AUTO       AUTO                   NONE
9        VR-Default  E      R    ON  AUTO       AUTO                   NONE
10       VR-Default  E      R    ON  AUTO       AUTO                   NONE
11       VR-Default  E      R    ON  AUTO       AUTO                   NONE
12       VR-Default  E      R    ON  AUTO       AUTO                   NONE
13       VR-Default  E      R    ON  AUTO       AUTO                   NONE
14       VR-Default  E      R    ON  AUTO       AUTO                   NONE
15       VR-Default  E      R    ON  AUTO       AUTO                   NONE
================================================================================
 > indicates Port Display Name truncated past 8 characterspback type
Link State: A-Active, R-Ready, NP-Port Not Present, L-Loopback type
Port State: D-Disabled, E-Enabled, L-License Disabledant media type
Media: !-Unsupported, $-Unlicensed detail" for redundant media type
Media Red: * - use "show port info detail" for redundant media type
Flow Cntrl: Shows link partner's abilities. NONE if Auto Neg is OFF
0->Clear Counters  U->page up  D->page down ESC->exit

History

This command was first available in ExtremeXOS 10.1.

The Port not present and Media variables were added in ExtremeXOS 11.2.

The no-refresh variable was added in ExtremeXOS 11.3.

The tag value was added in ExtremeXOS 12.4.4.

This command was updated to include flags that indicate the summary status of a non-Extreme optical device in ExtremeXOS 15.4.

The refresh keyword was added in ExtremeXOS 16.1.

Flag (L) to show port disabled due to lack of port speed license (applies to ExtremeSwitching X870-96x-8c switches only).

Platform Availability

This command is available on the Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X440-G2, X620, X690, X870 series switches.