show mpls rsvp-te lsp

show mpls rsvp-te lsp {{[destination | origin] ipaddress} {fast-reroute} {detail} | summary}

Description

Displays complete or filtered information for all RSVP-TE LSPs.

Syntax Description

destination Displays only those LSPs that terminate at the specified IP address.
origin Displays only those LSPs that originate at the specified IP address.
ipaddress Specifies an IP address for an LSP origin or destination.
fast-reroute Limits the display to only those LSPs with fast reroute protection.
detail Displays the LSP information in verbose format.
summary Displays only the LSP summary statistics section of the normal display.

Default

N/A.

Usage Guidelines

If no options are specified, information for all RSVP-TE LSPs is displayed.

You can limit the display to ingress, transit, or egress LSPs with the following commands:

show mpls rsvp-te lsp [ingress {fast-reroute} | ingress_lsp_name | ingressingress_lsp_name | ingress [destination | origin]ipaddress] {[all-paths | detail] | summary | down-paths {detail}} show mpls rsvp-te lsp [egress | transit] {fast-reroute} {{lsp_name} {[destination | origin] ipaddress} {detail} | summary}

When label recording is enabled for an LSP, labels are displayed only for the ingress node (the egress label from the previous node always matches the ingress node label).

Example

The following command example displays information about all RSVP-TE LSPs:

# show mpls rsvp-te lsp
Ingress LSP Name Path Name        Destination     Next Hop I/F     UpTm Flags
---------------- ---------------- --------------- ---------------- ---- --------
frrlsp1tom2      any              11.100.100.50   m2vlan1            5m UEF---IV
lsptom2          pathtom2         11.100.100.50   m2vlan1            5m UES--OIV
tom5             any              11.100.100.55   m5vlan1            5m UEP---IV
Egress LSP Name  Source IP       Destination     Prev Hop I/F     UpTm
---------------- --------------- --------------- ---------------- ----
tom3             11.100.100.55   11.100.100.30   m5vlan1            5m
frrlsp1tom3      11.100.100.50   11.100.100.30   m2vlan1            5m
tom3             11.100.100.50   11.100.100.30   m2vlan1            5m
Transit LSP Name Source IP       Destination     Prev Hop I/F  Next Hop I/F  UpTm
---------------- --------------- --------------- ------------- ------------- ----
tom2             11.100.100.55   11.100.100.50   m5vlan1       m2vlan1         5m
frrlsp1tom5      11.100.100.50   11.100.100.55   m2vlan1       m5vlan1         5m
lsptom5          11.100.100.50   11.100.100.55   m2vlan1       m5vlan1         5m
Flags: (U) Up, (E) Enabled, (P) Primary LSP, (S) Secondary LSP,
(F) FRR Primary LSP  (R) Redundant Paths, (B) Bandwidth Requested,
(O) ERO Specified,   (I) IP Traffic Allowed, (V) VPN Traffic Allowed,
(v) VPN Assigned Traffic Allowed
Summary of RSVP-TE LSPs
Ingress LSPs (Enabled/Disabled)          : 3 (3/0)
Ingress LSPs with no configured path     : 0
Ingress LSP Paths (Up/Down)              : 3 (3/0)
Detour LSP Paths (Up/Down)               : 0 (0/0)
Transit LSPs                             : 3
Egress LSPs                              : 3

The next command example displays only the summary information for all RSVP-TE LSPs:

# show mpls rsvp-te lsp summary
Summary of RSVP-TE LSPs
Ingress LSPs (Enabled/Disabled)          : 3 (3/0)
Ingress LSPs with no configured path     : 0
Ingress LSP Paths (Up/Down)              : 3 (3/0)
Detour LSP Paths (Up/Down)               : 0 (0/0)
Transit LSPs                             : 3
Egress LSPs                              : 3

The following command example limits the display to RSVP-TE LSPs with fast reroute protection:

# show mpls rsvp-te lsp fast-reroute
Ingress LSP Name Path Name        Destination     Next Hop I/F     UpTm Flags
---------------- ---------------- --------------- ---------------- ---- --------
frrlsp1tom2      any              11.100.100.50   m2vlan1            5m UEF---IV
Egress LSP Name  Source IP       Destination     Prev Hop I/F     UpTm
---------------- --------------- --------------- ---------------- ----
tom3             11.100.100.55   11.100.100.30   m5vlan1            5m
frrlsp1tom3      11.100.100.50   11.100.100.30   m2vlan1            5m
tom3             11.100.100.50   11.100.100.30   m2vlan1            5m
Transit LSP Name Source IP       Destination     Prev Hop I/F  Next Hop I/F  UpTm
---------------- --------------- --------------- ------------- ------------- ----
tom2             11.100.100.55   11.100.100.50   m5vlan1       m2vlan1         5m
frrlsp1tom5      11.100.100.50   11.100.100.55   m2vlan1       m5vlan1         5m
lsptom5          11.100.100.50   11.100.100.55   m2vlan1       m5vlan1         5m
Flags: (U) Up, (E) Enabled, (P) Primary LSP, (S) Secondary LSP,
(F) FRR Primary LSP  (R) Redundant Paths, (B) Bandwidth Requested,
(O) ERO Specified,   (I) IP Traffic Allowed, (V) VPN Traffic Allowed,
(v) VPN Assigned Traffic Allowed
Summary of RSVP-TE LSPs
Ingress FRR LSPs (Enabled/Disabled)        : 1 (1/0)
Ingress FRR LSPs with no configured path   : 0
Ingress FRR LSP Paths (Up/Down)            : 1 (1/0)
Detour LSP Paths (Up/Down)                 : 0 (0/0)
Transit FRR LSPs                           : 3
Egress FRR LSPs                            : 3

The following command example displays detailed information for all RSVP-TE LSPs:

# show mpls rs lsp det

Ingress LSP Name: lsp_to_baha
    Destination  : 11.100.100.4           Admin Status : Enabled
    IP Traffic   : Allow                  #VPLS Cfgd   : 0
    VPN Traffic  : Allow                  #VPLS In-Use : 0

    Path Name: path1
        Oper Status     : Enabled         UpTime              : 0d:0h:4m:49s
        Profile Name    : default        
        Peak Rate       : 0     Kbps      Max Burst Size      : 0 Kb
        Committed Rate  : 0     Kbps      Setup/Hold Priority : 7/0
        Record Route    : Enabled   
        MTU             : Use Local I/F
        Tunnel ID       : 1               Ext Tunnel ID       : 11.100.100.1
        LSP ID          : 0               State Changes       : 1
        LSP Type        : Primary         Bandwidth Cfgd      : False
        Activity        : Active         
        Failures        : 0               Retries-since last failure : 0
        Retries-Total   : 0              
        Configured ERO  : Order  IP Address/Mask     Type    Inc/Exc
                            100  9.50.1.2/32         strict  include
        Advertised Label: n/a                  Received Label : 0x00434
        Rx Packets      : n/a                  Tx Packets     : --
        Rx Bytes        : n/a                  Tx Bytes       : --
        Next Hop I/F    : 9.50.1.1 - j1-j2vlan1
        Next Hop Addr   : 9.50.1.2
        Record Route    : Indx  IP Address       Label
                        :    1  9.50.1.2         0x00434                        
                        :    2  9.54.1.4         0x00434                        

    Path Name: path2
        Oper Status     : Enabled         UpTime              : 0d:0h:4m:49s
        Profile Name    : default        
        Peak Rate       : 0     Kbps      Max Burst Size      : 0 Kb
        Committed Rate  : 0     Kbps      Setup/Hold Priority : 7/0
        Record Route    : Enabled   
        MTU             : Use Local I/F
        Tunnel ID       : 2               Ext Tunnel ID       : 11.100.100.1
        LSP ID          : 0               State Changes       : 1
        LSP Type        : Secondary       Bandwidth Cfgd      : False
        Activity        : Standby        
        Failures        : 0               Retries-since last failure : 0
        Retries-Total   : 0              
        Configured ERO  : Order  IP Address/Mask     Type    Inc/Exc
                            100  9.50.1.2/32         n/a     exclude
        Advertised Label: n/a                  Received Label : 0x00435
        Rx Packets      : n/a                  Tx Packets     : --
        Rx Bytes        : n/a                  Tx Bytes       : --
        Next Hop I/F    : 9.52.1.1 - j1-j4vlan1
        Next Hop Addr   : 9.52.1.4
        Record Route    : Indx  IP Address       Label
                        :    1  9.52.1.4         0x00435                    

History

This command was first available in ExtremeXOS 11.6.

This command and its output were modified, and the summary option was added in ExtremeXOS 12.0.

The fast-reroute feature was first available in ExtremeXOS 12.1.

This command and its output were modified in ExtremeXOS 12.2.2.

The output was modified to include the include/exclude information in ExtremeXOS 15.7.1.

Platform Availability

This command is available only on the platforms that support MPLS as described in the ExtremeXOS 32.2 Feature License Requirements document.