ACL Filters Behavior Differences

The implementation of ACL filters is similar in all VOSS switches but there are some differences as summarized in the following tables.

Note

The InVSN Filter shares the port-based groups in the following table.

Table 1. Hardware filter engine resources
VSP 4450 Series	VSP 4900 Series VSP 7200 Series VSP 8200 Series VSP 8400 Series	5420 Series 5520 Series VSP 7400 Series	VSP 8600 Series	XA1400 Series
If you enable Application Telemetry, IPv6 security filter commands and configurations are blocked and not available.	If you enable Application Telemetry, IPv6 security filter commands and configurations are blocked and not available.	If you enable Application Telemetry, IPv6 security filter commands and configurations are supported.	If you enable Application Telemetry, IPv6 security filter commands and configurations are supported.	Application Telemetry and IPv6 filters are not supported
All switches use a filter group as memory to store filter rules. The number of filter groups used can differ:
The switch supports four separate ingress filter groups: port-based Security ACEs port-based QoS ACEs VLAN-based Security ACEs VLAN-based QoS ACEs	The switch supports two ingress filter groups, where each group is shared by two filter types: port-based and VLAN-based Security ACEs port-based and VLAN-based QoS ACEs	The switch supports two ingress filter groups, where each group is shared by two filter types: port-based and VLAN-based Security ACEs port-based and VLAN-based QoS ACEs	The switch supports the following ingress filter group: port-based and VLAN-based ACEs	The switch supports one ingress filter group with two filter types: port-based and VLAN-based Security ACEs port-based and VLAN-based QoS ACEs
For each ingress packet, a parallel search is performed on each of the four filter groups.	For each ingress packet, a parallel search is performed on each of the two filter groups.	For each ingress packet, a parallel search is performed on each of the two filter groups.	For each ingress packet, a search is performed on the filter group.	For each ingress packet, a search is performed on the filter group.

Table 2. Incoming packet behavior
Filter	VSP 4450 Series	VSP 4900 Series VSP 7200 Series VSP 8200 Series VSP 8400 Series	5420 Series 5520 Series VSP 7400 Series	VSP 8600 Series	XA1400 Series
Can match both port-based and VLAN-based ACL/ACE	Regardless of the type of matching ACEs (Security or QoS), the action of either the highest priority matching ACE or the default action will be performed.	Port-based ACLs have precedence over VLAN-based ACLs. If the matching ACEs are of the same type (both Security or both QoS), then the VLAN-based ACL/ACE is ignored.	Port-based ACLs have precedence over VLAN-based ACLs. If the matching ACEs are of the same type (both Security or both QoS), then the VLAN-based ACL/ACE is ignored.	Port-based ACLs have precedence over VLAN-based ACLs. If a packet matches both a Port-based and a VLAN-based ACL, then the VLAN-based ACL is ignored.	Port-based ACLs have precedence over VLAN-based ACLs. If a packet matches both a Port-based and a VLAN-based ACL, then the VLAN-based ACL is ignored. Security ACEs have precedence over QoS ACEs. If packets match a Security and a QoS ACE, only the Security action is applied, the QoS action is ignored

Table 3. Action behavior
Filter	VSP 4450 Series	VSP 7200 Series VSP 8200 Series	VSP 4900 Series 5420 Series 5520 Series VSP 7400 Series VSP 8400 Series	VSP 8600 Series	XA1400 Series
ACE ID ranges supported	Security ACEs: 1–1000 QoS ACEs: 1001–2000 (IPv4 filters only)	Security ACEs: 1–1000 QoS ACEs: 1001–2000 (IPv4 filters only)	IPv4 filters: Security ACEs: 1–1000 QoS ACEs: 1001–2000 IPv6 filters: ACEs: 1–2000 support both security and QoS actions	ACEs: 1-1000 support both security and QoS actions.	Security ACEs: 1–1000 QoS ACEs: 1001–2000 (IPv4 filters only)
redirect-next-hop support	Supported in both the Global Routing Table and VRF contexts.	Supported in both the Global Routing Table and VRF contexts.	Supported in both the Global Routing Table and VRF contexts.	Supported in the Global Routing Table only.	Supported in both the Global Routing Table and VRF contexts.

Table 4. Egress filtering behavior
VSP 4450 Series	VSP 4900 Series VSP 7200 Series VSP 8200 Series VSP 8400 Series	5420 Series 5520 Series VSP 7400 Series	VSP 8600 Series	XA1400 Series
Configuring an ACE with the ARP operation qualifier is supported for OutPort ACLs.	Configuring an ACE with the ARP operation qualifier is supported for OutPort ACLs.	Configuring an ACE with the ARP operation qualifier is not supported for OutPort ACLs.	Configuring an ACE with the ARP operation qualifier is supported for OutPort ACLs.	Configuring an ACE with the ARP operation qualifier is supported for OutPort ACLs The Egress filters do not apply to the mirrored packets.

Table 5. ACL statistics behavior
VSP 4450 Series	VSP 4900 Series VSP 7200 Series VSP 8200 Series VSP 8400 Series	5420 Series 5520 Series VSP 7400 Series	VSP 8600 Series	XA1400 Series
Supports Viewing ACL Statistics by the ACE type Security and QoS.	Supports Viewing ACL Statistics by the ACE type Security and QoS.	Supports Viewing ACL Statistics by the ACE type Security and QoS.	Supports Viewing ACL Statistics by the ACE type QoS.	Supports Viewing ACL Statistics by the ACE type Security and QoS.

For QoS scaling and filter scaling information, see VSP 8600 Release Notes.