The V-WLC controls and manages access points and other controllers (at NOC or as a site-controller) in the network. The traffic between the access points and the V-WLC is over the layer-3 MINT protocol.
To install the VX or VX-DEMO license on an existing V-WLC instance, use the license command. For more information, see the examples provided in this section.
Service Platforms — NX 95XX, NX 96XX
vx9000 <MAC>
vx9000 <MAC>
| vx9000 <MAC> | Configures a V-WLC and enters its configuration mode. The V-WLC configuration is the same as that of a normal controller. |
nx9500-6C8809(config)#vx9000 11-22-33-44-55-66 nx9500-6C8809(config-device-11-22-33-44-55-66)#? Device Mode commands: adopter-auto-provisioning-policy-lookup Use centralized auto-provisioning policy when adopted by another controller adoption Adoption configuration adoption-site Set system's adoption site adoption-mode Configure the adoption mode for the access-points in this RF-Domain alias Alias application-policy Application Poicy configuration area Set name of area where the system is located arp Address Resolution Protocol (ARP) auto-learn Auto learning autogen-uniqueid Autogenerate a unique id autoinstall Autoinstall settings bluetooth-detection Detect Bluetooth devices using the Bluetooth USB module - there will be interference on 2.4 Ghz radio in wlan mode bridge Ethernet bridge captive-portal Captive portal cdp Cisco Discovery Protocol channel-list Configure channel list to be advertised to wireless clients cluster Cluster configuration configuration-persistence Enable persistence of configuration across reloads (startup configfile) contact Configure the contact controller WLAN controller configuration country-code Configure the country of operation critical-resource Critical Resource crypto Encryption related commands database Database command device-upgrade Device firmware upgrade dot1x 802.1X dpi Enable Deep-Packet-Inspection (Application Assurance) dscp-mapping Configure IP DSCP to 802.1p priority mapping for untagged frames email-notification Email notification configuration enforce-version Check the firmware versions of devices before interoperating environmental-sensor Environmental Sensors Configuration events System event messages export Export a file file-sync File sync between controller and adoptees floor Set the floor within a area where the system is located geo-coordinates Configure geo coordinates for this device gre GRE protocol hostname Set system's network name http-analyze Specify HTTP-Analysis configuration interface Select an interface to configure ip Internet Protocol (IP) ipv6 Internet Protocol version 6 (IPv6) l2tpv3 L2tpv3 protocol l3e-lite-table L3e lite Table layout-coordinates Configure layout coordinates for this device led Turn LEDs on/off on the device led-timeout Configure the time for the led to turn off after the last radio state change legacy-auto-downgrade Enable device firmware to auto downgrade when other legacy devices are detected legacy-auto-update Auto upgrade of legacy devices license License management command lldp Link Layer Discovery Protocol load-balancing Configure load balancing parameter location Configure the location logging Modify message logging facilities mac-address-table MAC Address Table mac-auth 802.1X mac-name Configure MAC address to name mappings management-server Configure management server address memory-profile Memory profile to be used on the device meshpoint-device Configure meshpoint device parameters meshpoint-monitor-interval Configure meshpoint monitoring interval min-misconfiguration-recovery-time Check controller connectivity after configuration is received mint MiNT protocol mirror Mirroring misconfiguration-recovery-time Check controller connectivity after configuration is received mpact-server MPACT server configuration neighbor-inactivity-timeout Configure neighbor inactivity timeout neighbor-info-interval Configure neighbor information exchange interval no Negate a command or set its defaults noc Configure the noc related setting nsight NSight ntp Ntp server WORD offline-duration Set duration for which a device remains unadopted before it generates offline event override Override a command override-wlan Configure RF Domain level overrides for wlan power-config Configure power mode preferred-controller-group Controller group this system will prefer for adoption preferred-tunnel-controller Tunnel Controller Name this system will prefer for tunneling extended vlan traffic radius Configure device-level radius authentication parameters raid RAID remove-override Remove configuration item override from the device (so profile value takes effect) rf-domain-manager RF Domain Manager router Dynamic routing rsa-key Assign a RSA key to a service sensor-server AirDefense sensor server configuration slot PCI expansion Slot spanning-tree Spanning tree timezone Configure the timezone traffic-class-mapping Configure IPv6 traffic class to 802.1p priority mapping for untagged frames trustpoint Assign a trustpoint to a service tunnel-controller Tunnel Controller group this controller belongs to use Set setting to use vrrp VRRP configuration vrrp-state-check Publish interface via OSPF/BGP only if the interface VRRP state is not BACKUP wep-shared-key-auth Enable support for 802.11 WEP shared key authentication clrscr Clears the display screen commit Commit all changes made in this session do Run commands from Exec mode end End current mode and change to EXEC mode exit End current mode and down to previous mode help Description of the interactive help system revert Revert changes service Service Commands show Show running system information write Write running configuration to memory or terminal nx9500-6C8809(config-device-11-22-33-44-55-66)#
| no | Removes a VX 9000 wireless controller |