select-shutdown

This feature enables auto-shutdown of select 2.4 GHz radios, in dual-band networks, to maintain co-channel interference (CCI) levels within specified limits. When enabled, Smart-RF monitors CCI levels to ensure that the deployment average CCI remains within specified minimum and maximum CCI limits. If the deployment average CCI is found to exceed the maximum threshold value, 2.4 GHz radios, causing neighbor interference, are shut down one-by-one until the deployment average CCI falls below the maximum threshold value. The reverse process occurs when the deployment average CCI falls below the minimum threshold value. In this scenario, previously disabled radios are enabled one-by-one until the deployed average CCI reaches acceptable levels.

Use this command to enable select-shutdown and configure the maximum and minimum CCI thresholds.

Supported on the following devices:

Access Points: AP5010, AP310i/e, AP410i/e, AP505i, AP510i, AP510e, AP560i, AP6522, AP6562, AP7161, AP7502, AP7522, AP7532, AP7562, AP7602, AP7612, AP7622, AP763, AP7662, AP8163, AP8543, AP8533.
Service Platforms: NX5500, NX7500, NX9500, NX9600
Virtual Platforms: CX9000, VX9000

Syntax

select-shutdown {cci-high-threshold|cci-low-threshold|frequency|frequency-limiter}

select-shutdown {cci-high-threshold <-85--55>}

select-shutdown {cci-low-threshold <-100--55>}

select-shutdown {frequency <0-3600>}

select-shutdown {frequency-limiter <1-1000>}

Parameters

select-shutdown {cci-high-threshold <-85--55>|cci-low-threshold <-100--55>|frequency <0-3600>|frequency-limiter <1-1000>}


select-shutdown	Enables auto-shutdown of selected 2.4 GHz radios to maintain the deployment average CCI levels within a specified range
cci-high-threshold <-85--55>	Optional. Configures the maximum CCI threshold <-85--55> – Specify a value from -85 - -55 dBm. The default value is -80 dBm. Note: If not specified, the system uses the default value as the upper limit.
cci-low-threshold <-100--55>	Optional. Configures the minimum CCI threshold <-100--55> – Specify a value from -100 - -55 dBm. The default value is -100 dBm. Note: If not specified, the system uses the default value as the lower limit.
frequency <0-3600>	Configures the interval, in minutes, at which 2.4 GHz radios are selected for shut down. When the deployment average CCI exceeds the specified maximum threshold, Smart RF shuts down 2.4 GHz radios until the CCI reaches acceptable levels. Use this option, to configure the interval between successive radio shut down. <0-3600> – Specify the frequency from 0 - 3600 minutes. The default is 60 minutes.
frequency-limiter <1-1000>	Configures the minimum multiple of Interference Recovery frequency that the select-shutdown frequency can be set to <1-100> – Specify a value from 1 - 1000. The default value is 15.

Examples

nx9500-6C8809(config-smart-rf-policy-testSmartRF)#select-shutdown 
cci-high-threshold -55

nx9500-6C8809(config-smart-rf-policy-testSmartRF)#select-shutdown 
cci-low-threshold -95

nx9500-6C8809(config-smart-rf-policy-test)#show context
smart-rf-policy test
 group-by floor
 sensitivity custom
 assignable-power 2.4GHz max 20
 assignable-power 2.4GHz min 8
 channel-list 2.4GHz 1,12
 channel-width 5GHz auto
 channel-width 2.4GHz auto
 area test channel-list 2.4GHz 1,2,3
 avoidance-time dfs 300
 interference-recovery channel-switch-delta 2.4GHz 5
 neighbor-recovery power-threshold 5GHz -65
 neighbor-recovery power-threshold 2.4GHz -82
 select-shutdown cci-high-threshold -55
 select-shutdown cci-low-threshold -95
 coverage-hole-recovery snr-threshold 2.4GHz 35
nx9500-6C8809(config-smart-rf-policy-test)#

Related Commands


no (smart-rf-policy-config-mode-command)	Disables select-shutdown of 2.4 GHz radios and reverts the select-shutdown parameters (maximum and minimum CCI thresholds, frequency, and frequency-limiter) to default values.